Analog Devices EV-PRG-MW1001ARDZ User manual

EV-PRG-MW1001ARDZ User Guide
UG-1664
One Technology Way •P. O. Box 9106 •Norwood, MA 02062-9106, U.S.A. •Tel: [phone] •Fax: [phone] •www.analog.com
EV-PRG-MW1001ARDZ Quick Start Guide
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 5
FEATURES
ADMW1001 programming device
Interfaces with MeasureWare Lab programming software
DEVELOPMENT KIT CONTENTS
EV-PRG-MW1001ARDZ
EQUIPMENT NEEDED
PC running Windows® 10
ST-Nucleo development board (ST-NUCLEO-F411RE)
SOFTWARE NEEDED
MeasureWare Lab software
EV-PRG-MW1001ARDZ PHOTOGRAPH
21863-001
Figure 1.
GENERAL DESCRIPTION
The EV-PRG-MW1001ARDZ is a firmware programming
board for the ADMW1001 device. The EV-PRG-MW1001ARDZ
contains a flip cap socket for rapid programming of small volumes
of the ADMW1001. MeasureWare Lab software controls a hot
swapping sequence to allow insertion and removal of the
ADMW1001 ICs before and after the programming procedure.
The latest version of firmware is available on the MeasureWare
Lab page, and enables new features and sensors connectivity.
For large volume programming of the ADMW1001, contact
Analog Devices, Inc.
For full specifications on the ADMW1001, see the ADMW1001
data sheet, which must be consulted in conjunction with this
user guide when using the EV-PRG-MW1001ARDZ.
Downloaded from Arrow.com.

UG-1664 EV-PRG-MW1001ARDZ User Guide
Rev. 0 | Page 2 of 5
TABLE OF CONTENTS
Features .............................................................................................. 1
Development Kit Contents.............................................................. 1
Equipment Needed........................................................................... 1
Software Needed............................................................................... 1
EV-PRG-MW1001ARDZ Photograph .......................................... 1
General Description ......................................................................... 1
Revision History ................................................................................2
EV-PRG-MW1001ARDZ Quick Start............................................3
Evaluation Board Software...............................................................4
Software Installation .....................................................................4
REVISION HISTORY
11/2019—Revision 0: Initial Version
Downloaded from Arrow.com.Downloaded from Arrow.com.

EV-PRG-MW1001ARDZ User Guide UG-1664
Rev. 0 | Page 3 of 5
EV-PRG-MW1001ARDZ QUICK START
To pro g r am t he ADMW1001 IC with the EV-PRG-
MW1001ARDZ, take the following steps:
1. Install the MeasureWare Lab software as outlined in the
Software Installation section.
2. Connect the ST-NUCLEO-F411RE to the EV-PRG-
MW1001ARDZ using the Arduino headers. The
ST-NUCLEO-F411RE connects to the PC via the USB
cable provided in the ST-NUCLEO-F411RE kit.
3. The MeasureWare Lab software automatically recognizes
that the EV-PRG_MW1001ARDZ is connected and a
programming window appears.
4. Place an ADMW1001 inside socket X1 on the EV-
PRG_MW1001ARDZ and click Program in the
MeasureWare Lab software. Do not remove the
ADMW1001 IC until the software has completed
programming. Programming takes approximately 30 seconds.
5. When prompted, remove the ADMW1001 IC.
6. Choose the option to reprogram or exit the MeasureWare
Lab software.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

UG-1664 EV-PRG-MW1001ARDZ User Guide
Rev. 0 | Page 4 of 5
EVALUATION BOARD SOFTWARE
SOFTWARE INSTALLATION
The EV-PRG-MW1001ARDZ requires MeasureWare Lab
software to program the latest firmware to the ADMW1001 IC.
The MeasureWare Lab software can be downloaded from the
executable file available on the MeasureWare Lab webpage.
Double-click the MeasureWareLab.exe file and follow the on
screen instructions to install this file on the PC.
21863-002
Figure 2. MeasureWare Lab Software Installation
Follow the on screen instructions to install the ST-Nucleo driver
pack. This driver pack ensures that the USB on the PC is able to
communicate with the host microcontroller through a USB to
universal asynchronous receiver/transmitter (UART) converter.
When the software is installed, navigate to Start > Programs >
Analog Devices > MeasureWare_Lab to execute the software
program.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

EV-PRG-MW1001ARDZ User Guide UG-1664
Rev. 0 | Page 5 of 5
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITEDTO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2019 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG21863-0-11/19(0)
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.