Analog way Pulse LE User manual

The Pulse LE front panel is comprised of several sections, each carefully labelled and self
explanatory, corresponding to all of the machine’s versatile functions.
The STANDBY button (1) will allow users to turn the device on and off once the main outlet switch
(14) is turned on. The menu screen (2), and Control section (3), menu scroll knob (4) will give users
access to the Pulse LE menu. The Layer Selection section (5) will allow users to select which source
the Pulse LE will work on, while the PIP (7), and Background Live (9) buttons, determine which of
the 10 available input sources will be used in that layer. The FREEZE button (8) allows users to take
a snapshot of the displayed image, and the TAKE button (11) will display your Preview Screen to
the Main outputs (20).The EFFECT button (10) and the PRESET button (6) are both shortcuts to the
Pulse LE menu Presets page.
The rear panel of the Pulse will let you connect all your input sources and outputs to your device.
Plug universal analog sources (17), DVI-I sources (18) and HD-SDI sources (19) to your Pulse LE.
Connect audio inputs and outputs (21 and 22), and a remote controller to the IP/LAN connector (16).
Plug displays to the Main and Preview outputs (20).
QUICK START
What’s in the box
Pulse LE Overview
Thank you for choosing Analog Way and the Pulse LE. By following these simple steps, you should
be able to setup and use your powerfull scaler/switcher within minutes. Discover the Pulse LE
extensive capabilities and intuitive interface while conguring your rst show, and unleash your
creativity for a new experience in show and event management by Analog Way.
Pulse LE - PLS200
1 x Pulse LE seamless scaler/switcher
1 x Power supply cord
2 x DVI male to HD15 female and DVI female cable
1 x HD15 to 5 BNC cable
1 x Ethernet crossover cable
1 x Set of 3 audio 5 pin screw terminals
1 x RCS CD-ROM (PC only)
1 x User manual CD-ROM (Mac and PC)
1 x Quick Start guide
4 x M4x12mm screws
WARNING!
If required, front handles of the device can be dismantled,
but with caution.
The original screws removed must not be reintroduced to
their location without handles in place.
Substantial damages can occur, including risk of electric
shock from the mains voltage.
Only M4x12mm screws can be used.
(They are supplied with the unit)

Setting up the Pulse LE LE
WORKING WITH THE PULSE LE
Connect all sources (PC, video camera, streaming server, DVD player...) to the appropriate input
connectors at the rear of the unit (see “The Pulse LE rear panel” p.22 of the User Manual).
Connect your main output to the video projector for audience viewing, and your preview output to
a monitor for preview purposes (see “Connecting the Pulse LE”, p.21 of the User Manual). Turn all
input and output devices on.
Connect the supplied AC power cord to the unit, then connect the other end of the cord to a grounded
AC outlet. Power up the Pulse LE by pressing the I/0 button at the rear of the unit, and wait for
the menu to run its startup sequence. The unit is on and ready to function when the System Menu
appears on your VFD screen.
The following setup is an example of a typical Pulse LE conguration for an event or roadshow, but
can of course be modied according to your specic needs:

The Pulse LE offers several different layer types to work with:
- PIP: a PIP allow you to resize, position and add borders and
transition effects to layers.
1/ In the Layer Selection section, press the PIP button. On the
preview screen, the layer will appear as a color rectangle, and
“00” will be indicated in the layer rectangle.
2/ In the Input Selection section, press the source button (1-10)
of the source you wish to affect to the selected PIP. On your
preview screen, the source will appear in the layer rectangle,
and PIP will be indicated in the layer rectangle.
3/ Press the PIP button, then rotate the scroll knob to
access desired layer attributes (size, position, zoom, border,
transparency...) and press the corresponding ENTER button in
the Layer sub-menu to enter and adjust layer attributes.
1/ In the menu section, press the EXIT/MENU button and select
Input in the menu by rotating the selection knob and press the
ENTER button to enter the Input sub-menu.
2/ Select Auto Setting and press enter to automatically congure
the inputs plugged into the Pulse LE. The device will set all
input resolutions and frequencies to match the input sources
plugged to the device.
3/ Alternatively, you can congure all inputs of the Pulse LE
individually, by navigating to the Input menu and setting each
input accordingly.
Once your inputs have all been congured, the output settings
of the Pulse LE must be set according to the machines plugged
on your Pulse LE Main and Preview outputs (video projector,
preview monitor...).
1/ In the menu section, press the EXIT/MENU button and select
Output in the menu by rotating the selection knob. Enter the
Output sub-menu and select the output type, resolution and
frequency, so that they match the viewing hardware plugged
into the unit.
2/ Press the ENTER button to enter each of the desired output
parameters.
Your Pulse LE is now set up and ready to work with.
Pulse LE layers
Input & Output conguration

Whether catering to complex event setups, or putting together
intricate shows, your Pulse LE will deliver exciting transitions
and like you could expect from a dedicated mixer.
1/ In the Layer Selection section, press the PIP button. The
button will start blinking. On your Preview screen, PIP1 will
appear as a color rectangle. The parameters of the layer will
automatically appear on your Pulse LE VFD menu screen.
2/ In the Layer menu, make the position, size, border and
transparency settings you like, then select Opening Effect in the
layer options, press the ENTER button and select Type. Select
an opening effect and press the ENTER button. Navigate to
Duration in the Opening Effect sub-menu, and set the duration
of your effect by rotating the selection knob and pressing
ENTER.
3/ Set a closing effect for your PIP by navigating to the Closing
Effect menu, then press TAKE to view the transition effect on
your Main output.
Making a transition
Going further with the Pulse LE
You should now have all the basic skills needed to start operating
the Pulse LE. We recommend reading the User Manual
supplied with the Pulse LE on the CD-ROM, and encourage
you to play with the unit’s extensive functionalities, there is
no better way to familiarize yourself with your new shows and
events tool. The Menu Tree of the Pulse LE (p.30 of the User
Manual), was designed to be printed for easy reference of all
of the machine’s numerous functions. We recommend keeping
a copy of this handy when you start working with the Pulse LE.
Though particular attention has been brought to the enclosed
User Manual to bring you a thorough and easy to follow guide
for your Pulse LE, further detail and more documentation can
also be found on our website : www.analogway.com.
4/ By pressing the source button again, the Image sub-menu
appears on your menu VFD screen. Rotate the scroll knob
to access the desired source attributes (aspect in/out, color,
centering, blanking adjust...) and press the ENTER button in
the Image sub-menu to enter and adjust source attributes.
5/ Press TAKE to view the results on your main screen.
- LIVE BACKGROUND: To work with a live background, simply
press the BACKGROUND LIVE button, then select a live input
source from the Input Selection section of the Pulse LE. The
background will appear on your Preview. Simply press the
TAKE button to view the results on your Main output.
Version: 3.0 - 06/01/2010
Code: 140108