Ancona Comfort 8 User manual

Comfort 8 Wall Hardwire
Installation and Operations Manual
11/29/2017MAAN0512-0001-01

ALLEN KEY
FLAT HEAD SCREWDRIVERS
STARHEAD SCREWDRIVERS
PENCIL
DRILL & BIT
LEVEL
MEASURING TAPE
Long Screw
4 pcs
4 pcs
Fig . 1
REQUIRED TOOLS
PARTS FOR WALL-MOUNTED HARDWIRE INSTALLATION
4 pcs Ø8 mm
all Post
4 pcs
ELECTRICAL REQUIREMENTS: 120V, 130W, 60Hz, 1.1A
i
Allen Key (large)
1pc
j
l
Allen Key (small)
1pc
Large Set Screw
4pcs
Metal
Metal Wall Leg
Set Screw
4pcs
Plate
1pc
4 pcs
iWall Plate Screws
2 pcs
PRODUCT DIMENSIONS
800 mm (31 1/2)" 63.5 mm (2 1/5")
167.5 mm (6 1/2")

INSTALLATION
Step 1: Verifying installation parts (Fig.1)
-)1.giFeeS(.remrawlewotruoyhtiwdeilppuserewnoitallatsnignitnuomrofstrapllaerusnE
-If any are missing, please contact us.
)2.giF(sgelllawlatemgnillatsnI:2petS
-Locate the following parts:
ogeLlllaWlateM:d
oe: Large Screw to set post in main body (this part may already be installed inside the Metal Wall Leg)
o)geLllaWlateMehtedisnidellatsniebydaerlayamtrapsiht(tresnIcitsalP:f
o)6.giFeeS()geLllaWlateMehtedisnidellatsniebydaerlayamtrapsiht(wercSteS:g
-Position parts correctly:
o)dgeLllaWlateMedisnidenoitisopsi)ftresnIcitsalP
oSet Screw g) is inserted in Metal Wall Leg d) (See Fig.6)
oIf the Metal Post b) is inserted into the Metal Wall Leg d) remove it
-Install Metal Wall Leg d)
o Position Metal Wall Leg d) onto the towel warmer where the Large Screws e) can be inserted
oInsert Large Screw e) and screw Metal Wall Leg d)into main body using appropriate sized Allen key
oRepeat for all four (4) Metal Wall Legs
1. Install in accordance with n onal and local
codes
2. Do not install in the shower, sauna or any wet
lo ons
3. Make sure towel warmer is properly secured
to the wall before use.
24”
Fig. 2
oLarge Screw e) is positioned inside the Plastic Insert f)

INSTALLATION (cont.)
Step 3: Marking holes for wall mount posts (Fig. 3)
-Take towel warmer with four (4) Metal Wall Legs mounted, as per Step 2
-Position against the wall where you will want to install the towel warmer
-gelsihtkramoslanacuoyosseerged09tanidenrutoslasigeLeriWdraHehterusnE
-Use light pencil to mark legs on the wall (you may want to erase the pencil mark following
installation completion, so make sure you mark lightly)
Step 4: Installing wall posts (Fig.4)
-If installing on dry wall with no rear beam support (e.g. wood studs):
o3petSrepsallawehtnodekramselcric)4(ruofehtfohcaeforetnecehtnielohallirD
o)adedivorpgulPcitsalPehttresniothguoneegralsielohdellirdehterusnE
oseloh)4(ruofehtfohcaeotnigulPcitsalPehtwercs/tresnI
oecalpnitesot)cwercSnitupdnagulPcitsalPfopotno)btsoPllaWnoitisoP
-If installing on surface with rear support, e.g. wood studs (no need for Plastic Plug a)
oPre-drill small hole in the center of each circle as per step 3
oPosition Wall Post b) on top of pre-drilled hole and put in Screwc) to set in place
Step 5: Installing hard wire leg (Fig.5)
-Create a hole in the wall to let the Hard Wire Leg go through (approx. 2” x 3 3/4”)
-The leg will be covered by Plate h) so the hole should be large enough to allow space for
electrical connection and leg to go through but not too large so that the plate can cover it fully
- Electrical wiring must be done by qualified professionals and in accordance with all applicable
codes and standards, including fire-rated constructions (refer to Electrical Requirements on Page 1)
Step 6: Mounting main body onto wall (Fig.6)
-Take main body and position each of the four (4) legs on top of the Wall Posts b)
-Once inserted use appropriate sized Allen key to tighten each Set Screw g)
-etelpmocebwondluohsnoitallatsniehT
Step 7: Test the towel warmer
-Remove protective white caps, they are located at the end of each of the vertical bars
-Turn the switch on to start towel warmer; the On-Off switch is located at the end of one of the
posts
-The towel warmer should reach its pre-set temperature in approximately 15 minutes
-This towel warmer is designed to operate continuously and can be left on all the times. To save
electricity it can be turned off when not in use.
Fig. 4 Fig. 6
Fig. 3
h
Fig. 5

Operation and Maintenance Instructions
•After installation, connect the electric power and turn on the switch. The indicator light will show red and
the towel warmer will start to work.
•Turn off the switch when the towel warmer is not in use. The indicator light will turn dark and the towel
warmer will stop working.
•Clean the towel warmer with a soft dry towel. Do not clean with abrasive cleaning powder.
PROPERLY HANG
TOWELS.
DO NOT OVERLAP
TOWELS.
CAUTION - Overlapping towels may increase towel warmer temperatures.
•Towel warmers are designed for heating towels and bathrobes and should not be used for other purposes.
The manufacturer or reseller assumes no liability if the device is used in combination with equipment or
accessories not sold by the manufacturer.
•Never stand, sit or climb on the unit.
•This towel warmer operates at high temperatures that can cause burns. Do not touch surfaces of the towel warmer
while the warmer is in operation. The unit is designed to warm up towel and may become very hot.
•Do not allow unsupervised children in the vicinity of the towel warmer; and warn children of hot surfaces. An adult
must supervise when the device is used by or near children.
•Unplug the unit and ensure that the electrical circuit breaker is off the main panel before wiring, carrying
out a repair or servicing your heated towel warmer.
•Do not place your towel warmer inside a shower, sauna or plunge into the water.
•To ensure continued protection against risk of electric shock, plug the unit into a properly grounded outlet.
•Approved for domestic use only. Do not use outdoors.
Information : [email protected] or 1-800-350-4562
HIGH OPERATING TEMPERATURE!