Annovi Reverberi Blue Clean 935 - 945 User manual

FR
EN
DE
IT
ES
PT
EL
NL
DA
NO
FI
SV
CS
PL
SL
SK
LT
BG
RU
HU
RO
TR
HR
LV
ET
cod. 90656 - EZ
UK
935 - 945

2
FR Lire ce manuel avant l’installation/utilisation du nettoyeur en faisant très attention aux INSTRUCTIONS POUR LA SÉCURITÉ
EN Read this manual through carefully before installing/using the cleaner, paying special attention to the SAFETY
INSTRUCTIONS
DE Lesen Sie dieses Handbuch vor der Installation und dem Gebrauch des Hochdruckreinigers aufmerksam durch und achten
Sie besonders auf die SICHERHEITSANWEISUNGEN
IT Leggere questo manuale prima dell’installazione/uso dell’idropulitrice, prestando particolare attenzione alle ISTRUZIONI
PER LA SICUREZZA
ES Leer este manual antes de la instalación/uso de la hidrolimpiadora, prestando particular atención a las INSTRUCCIONES
SOBRE SEGURIDAD
PT Leia este manual antes de instalar/usar a lavadora a alta pressão, prestando muita atenção nas INSTRUÇÕES PARA A
SEGURANÇA
EL Διαβάστε το παρόν εγχειρίδιο πριν από την εγκατάσταση/χρηση του μηχανήματος πλύσης, με ιδιαίτερη προσοχή στις
ΟΔΗΓΙΕΣ ΓΙΑ ΤΗΝ ΑΣΦΑΛΕΙΑ
NL Lees vóór de installatie/het gebruik van de hogedrukreiniger deze handleiding goed door en in het bijzonder de
VEILIGHEIDSVOORSCHRIFTEN
DA Læs denne vejledning inden installation og brug af højtryksrenseren og vær særligt opmærksom på SIKKERHEDSREGLERNE
NO Les denne håndboken før installasjon og bruk av høytrykksspyleren og vær spesielt oppmerksom på SIKKERHETSREGLENE
FI Lue tämä käyttöopas ennen painepesurin asennusta/käyttöä. Kiinnitä erityistä huomiota TURVAOHJEISIIN
SV Läs igenom bruksanvisningen före installation och användning av högtryckstvätten. Lägg speciellt märke till
SÄKERHETSBESTÄMMELSERNA
CS Před instalací nebo používáním tohoto čističe si pečlivě přečtěte tuto příručku. Zvýšenou pozornost věnujte části
BEZPEČNOSTNÍ POKYNY
PL Przed przystąpieniem do instalacji bądź użycia myjki należy dokładnie przeczytać niniejszy podręcznik, zwracając
szczególną uwagę na treść części dotyczącej INSTRUKCJI BEZPIECZEŃSTWA
SL Pozorno preberite ta navodila pred namestitvijo/uporabo čistilnika, pri čemer posebno pozornost namenite VARNOSTNIM
NAVODILOM
SK Pred inštaláciou/používaním čističa si pozorne prečítajte tento návod a buďte obzvlášť opatrní pri čítaní BEZPEČNOSTNÝCH
POKYNOV
LT Prieš sumontuodami ir naudodami įrenginį atidžiai perskaitykite šią naudojimo instrukciją, ypatingą dėmesį atkreipdami
į SAUGOS INSTRUKCIJAS
BG Прочетете това ръководство внимателно, преди да инсталирате/използвате машината за почистване,
като обърнете особено внимание на ИНСТРУКЦИИТЕ ЗА БЕЗОПАСНОСТ
RU Прочитайте данное руководство перед установкой моечной машины, обращая особенное внимание на
ИНСТРУКЦИИ ПО БЕЗОПАСНОСТИ
HU A tisztítóberendezés üzembehelyezése/használata előtt olvassa át gondosan ezt a leírást, különös figyelmet szentelve a
BIZTONSÁGI ELŐÍRÁSOK című résznek
RO Citiţi acest manual în întregime cu atenţie înainte de a instala/utiliza aparatul de curăţat, acordând o atenţie mărită
INSTRUCŢIUNILOR DE SIGURANŢĂ
TR Hidro temizleyiciyi kurmadan/kullanmadan önce, EMNİYET BİLGİLERİ’NE özellikle dikkat göstererek, işbu kılavuzu
okuyunuz
HR Prije montiranja/korištenja čistača pažljivo pročitajte ovaj priručnik i posebnu pozornost posvetite SIGURNOSNIM
MJERAMA
LV Pirms tīrīšanas ierīces uzstādīšanas/izmantošanas izlasiet šo rokasgrāmatu, īpaši vērīgi lasiet DROŠĪBAS NOTEIKUMUS
ET Lugege see kasutusjuhend enne survepesuri töökorda seadmist/kasutamist hoolega läbi, pöörates erilist tähelepanu
OHUTUSNÕUETELE
UK Перед тим, як встановлювати/використовувати пристрій для миття, уважно прочитайте цей посібник,
звертаючи особливу увагу на ІНСТРУКЦІЇ З БЕЗПЕКИ

3
1
A2
A3
A1
D
B5
C1
C5
B1
B2
B3
E1E2
B2
C2

4
2
1 2
43
6 7
8 9 10
5
CH 17
Ø13

5
3
4
psi
bar
0
max
F
H
I
D
1
2
I
O
D
2
I
1
L1
L2
L3
G
E

6
I
5
Volt
400 4 x 1,5 mm24 x 2,5 mm2
1 ÷ 25 m 25 ÷ 50 m
L
TSS
3
5 4
2 1
A2
A1
M 3~
T3 T2 T1
5
R
3 1
S
T
L3 L2 L1
3~ 400 [V]

10 English
EN
1
GENERAL INFORMATION FIG.1
1.1 Use of the manual
This manual forms an integral part of the appliance and should be
kept for future reference. Please read it carefully before installing/
using the unit. If the appliance is sold, the Seller must pass on this
manual to the new owner along with the appliance.
1.2 Delivery
The appliance is delivered partially assembled in a cardboard box.
The supply package is illustrated in fig.1.
1.2.1 Documentation supplied with the appliance
A1 Use and maintenance manual
A2 Safety instructions
A3 Declaration of conformity
1.3 Disposing of packaging
The packaging materials are not environmental pollutants but must
still be recycled or disposed of in compliance with the relevant
legislation in the country of use.
1.4 Safety signs
Comply with the instructions provided by the safety signs fitted to
the appliance.
Check that they are present and legible; otherwise, fit replacements
in the original positions.
E1 sign – Indicates that the appliance must not be disposed of as
municipal waste; it may be handed in to the dealer on purchase of a
new appliance. The appliance's electrical and electronic parts must
not be reused for improper uses since they contain substances
which constitute health hazards.
1.4.1 Symbols
E2 symbol – Indicates that the appliance is intended for
professional use, i.e. for experienced people informed
about the relative technical, regulatory and legislative
aspects and capable of performing the operations neces-
sary for the use and maintenance of the appliance.
E3 symbol – Indicates that the appliance is intended for
non-professional (domestic) use.
2
TECHNICAL INFORMATION FIG.1
2.1 Envisaged use
This appliance has been designed for individual use for the cleaning
of vehicles, machines, boats, masonry, etc, to remove stubborn dirt
using clean water and biodegradable chemical detergents.
Vehicle engines may be washed only if the dirty water is disposed of
as per regulations in force.
- Intake water temperature: see data plate on the appliance.
- Intake water pressure: below 10 bar.
- Operating ambient temperature over 0°C in accordance with
standard EN 60335-2-79/A1 only for domestic model (see sym-
bol E3).
2.2 Operator
The symbol on the front cover identifies the appliance’s intended
operator (professional or non-professional).
2.3 Improper use
Use by unskilled persons or those who have not read and under-
stood the instructions in the manual is forbidden.
The introduction of inflammable, explosive and toxic liquids into the
appliance is prohibited.
Use of the appliance in a potentially inflammable or explosive
atmosphere is forbidden.
The use of non-original spare parts and any other spare parts not
specifically intended for the model in question is prohibited.
All modifications to the appliance are prohibited. Any modifications
made to the appliance shall render the Declaration of Conformity
null and void and relieve the manufacturer of all liability under civil
and criminal law.
2.4 Main components
B1 Adjustable spray nozzle
B2 Lance
B3 Gun with safety catch
B4 Power supply cable with plug
B5 High pressure hose
B6 Detergent tank (on models with this feature)
2.4.1 Accessories (where applicable – see fig.1).
C1 Nozzle cleaning tool
C2 Rotating nozzle kit
C3 Handle
C4 Brush
C5 Hose reel
2.5 Safety devices
Caution - Danger!
Do not tamper with or adjust the safety valve set-
ting.
- Safety valve and pressure limiting valve.
The safety valve is also a pressure limiting valve. When the gun
trigger is released, the valve opens and the water recirculates
through the pump inlet.
- Safety catch (D): prevents accidental spraying of water.
3
INSTALLATION FIG.2
3.1 Assembly
Caution - Danger!
All installation and assembly operations must be
performed with the appliance disconnected from the mains
power supply.
The assembly sequence is illustrated in fig.2.
3.2 Assembling the rotating nozzle
(For models with this feature)
The rotating nozzle kit delivers greater washing power.
3.3 Electrical connection
Caution - Danger!
Check that the electrical supply voltage and frequen-
cy (V-Hz) correspond to those specified on the appliance
data plate (fig.2). The appliance should only be connected
to a mains power supply equipped with an adequate earth
connection and a differential security breaker (30 mA)
to cut off the electricity supply in the instance of a short
circuit.
3.3.1 Use of extension cables
Use cables featuring “IPX5” protection level.
The cross-section of the extension cable should be pro-
portionate to its length; the longer it is, the greater its
cross-section should be. See table I.
3.4 Water supply connection
Caution - Danger!
Only clean or filtered water should be used for intake.
The delivery of the water intake tap should be equal to that
of pump capacity.
Place the appliance as close to the water supply system as possible.
3.4.1 Connection points
l Water outlet (OUTLET)
n Water inlet with filter (INLET)
3.4.2 Connection to the mains water supply
The appliance can be connected directly to the mains
drinking water supply only if the supply hose is fitted with
a backflow preventer valve as per current regulations in
force. Make sure that the hose is at least Ø 13 mm and
that it is reinforced.

11English
EN
4
ADJUSTMENT INFORMATION FIG.3
4.1 Adjusting the spray nozzle (for models with this feature)
Water flow is adjusted by regulating the nozzle (E).
4.2 Adjusting the detergent (on models with this feature)
Detergent flow is adjusted using the regulator (F).
4.3 Adjusting the detergent pressure
Set the adjustable nozzle on " " to deliver detergent at the correct
pressure (on models with this feature).
4.4 Adjusting the pressure (on models with this feature)
The regulator (G) is used to adjust the working pressure. The pres-
sure is shown on the pressure gauge (where fitted).
5
INFORMATION ON USE OF THE APPLIANCE FIG.4
5.1 Controls
- Starter device (H).
Set the starter switch on (ON/1) to:
a) start the motor (in models without TSS device);
b) set the motor ready to start (in models with TSS device).
If there is a pilot light on the starter device, it should light up.
If the “low/high” settings are available, use them as follows:
Low : low pressure washing
High : high pressure washing
Set the starter device switch on (OFF/0) to shut down the applian-
ce.
If there is a pilot light on the starter device, it should go out.
- Water jet control lever (I).
Caution - Danger!
During operation the appliance must be positioned
as shown in fig. 4 on a sturdy, stable surface.
5.2 Start-up
Caution - Danger!
Before starting up the appliance check that the water
supply hose is connected properly; use of the appliance
without water will damage it; do not cover the ventilation
grilles when the appliance is in use.
On three-phase models for professional use, at first use start the
appliance for a very short time to check that the motor is running
in the correct direction. If the motor fan is turning anti-clockwise,
exchange two of the three phase wires (L1, L2, L3) in the electrical
plug.
1) Turn on the water supply tap fully.
2) Release the safety catch (D).
3) Depress the gun trigger for a few seconds and start up the appli-
ance using the starter device (ON/1).
TSS models - In TSS models with automatic delivery flow cut-off
system:
- when the gun trigger is released the dynamic pressure automati-
cally cuts out the motor (see fig.4);
- when the gun trigger is depressed the automatic drop in pres-
sure starts the motor and the pressure is restored after a very
slight delay;
- if the TSS is to function correctly all gun releasing and depress-
ing operations must be performed at intervals of less than 4-5
seconds.
To prevent damage to the appliance, when running do not
stop the water jet for more than 10 minutes at a time.
5.3 Stopping the appliance
1) Set the starter device switch on (OFF/0).
2) Depress the gun trigger and discharge the residual pressure
inside the hoses.
3) Engage the gun safety catch (D).
5.4 Restarting
1) Release the safety catch (D).
2) Depress the gun trigger and discharge the residual air inside
the hoses.
3) Set the starter device on (ON/1).
5.5 Storage
1) Switch the appliance off (OFF/0).
2) Remove the plug from the socket.
3) Turn off the water supply tap.
4) Discharge the residual pressure from the gun until all the water
has come out of the nozzle.
5) Drain the detergent tank.
6) Engage the gun safety catch (D).
5.6 Refilling and using detergent
When using detergent, the adjustable nozzle must be set on
" " (on models with this feature).
Fill the tank with highly degradable detergent.
5.7 Recommended cleaning procedure
Dissolve dirt by applying the detergent mixed with water to the
surface while still dry.
When dealing with vertical surfaces work from the bottom upwards.
Leave the detergent to act for 1-2 minutes but do not allow the
surface to dry. Starting from the bottom, use the high pressure jet
at a minimum distance of 30 cm. Do not allow the rinse water to run
onto unwashed surfaces.
6
MAINTENANCE FIG.5
Any maintenance operations not covered by this chapter should be
carried out by an Authorized Sales and Service Centre.
Caution - Danger!
Always disconnect the plug from the power socket
before carrying out any work on the appliance.
6.1 Cleaning the nozzle
1) Disconnect the lance from the nozzle.
2) Remove any dirt deposits from the nozzle hole using the tool
(C1).
6.2 Cleaning the filter
Clean the suction filter (L) and the detergent filter after every 50
hours of operation.
6.3 Unjamming the motor (on models with this feature)
In case of lengthy stoppages, limescale sediments may cause the
motor to seize. To unjam the motor, turn the drive shaft with a
tool (M).
6.4 End-of-season storage
Treat the appliance with non-corrosive, non-toxic antifreeze before
storing it away for winter.

12 English
EN
7
TROUBLESHOOTING
Problem Possible causes Remedy
Pump does not reach working
pressure
Nozzle worn Replace nozzle
Water filter fouled Clean filter (fig.5)
Water supply pressure low Turn on water supply tap fully
Air being sucked into system Check tightness of hose fittings
Air in pump
Switch off the appliance and keep depressing and releas-
ing the gun trigger until the water comes out in a steady
flow. Switch the appliance back on again.
Adjustable nozzle not positioned correctly Turn the adjustable nozzle (E) (+) (fig.3)
Pressure drops during use
Water intake from external tank Connect appliance to the mains water supply
Intake water too hot Reduce temperature
Nozzle clogged Clean nozzle (fig.5)
Motor “sounds” but fails to start
Insufficient power supply Check that the voltage of the mains power supply line is
the same as that on the plate (fig.2)
Voltage loss due to use of extension cable Check characteristics of extension cable
Appliance not used for a long period of time Contact your nearest Authorized Service Centre
Problems with TSS device Contact your nearest Authorized Service Centre
Motor fails to start
No electrical power Check that the plug is firmly in the socket and that the
mains voltage supply is present (*)
Problems with TSS device Contact your nearest Authorized Service Centre
Appliance not used for a long period of time Using the tool (L) unjam the motor from the hole at the
rear of the appliance (in models with this feature) (fig.5)
Water leakage Seals worn Have the seals replaced at your nearest Authorized
Service Centre
Appliance noisy Water too hot Reduce temperature (see technical data
Oil leakage Seals worn Contact your nearest Authorized Service Centre
TSS versions only: motor starts
even with gun trigger is released
Nozzle clogged Clean nozzle (fig.5)
High pressure system or pump hydraulic circuit not
watertight Contact your nearest Authorized Service Centre
TSS versions only: no water deliv-
ery when gun trigger is depressed
(with supply hose connected)
Nozzle clogged Clean nozzle (fig.5)
If the motor starts and does not restart during operation, wait 2-3 minutes before repeating the start-up procedure (overload cutout has been tripped).
If the problem recurs more than once, contact your nearest Authorized Service Centre.

87
DÉCLARATION DE CONFORMITÉ FR
Nous déclarons, en assumant la pleine responsabilité
de cette déclaration, que le produit est conforme aux
normes suivantes et aux documents correspondants
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
Selon les prescriptions des directives:
98/37/CE
2006/95/CE, 2002/95/CE, 2002/96/CE, 89/336/CE, 2000/14/CE
Date : 02/02/2007
MODENA (I)
Stefano Reverberi
Managing Director
PROHLÁŠENÍ O SHODĚ CS
Prohlašujeme na vlastní odpovědnost,
že tento výrobek je ve shodě s následujícími
normami nebo standardizovanými dokumenty
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
v souladu s předpisy:
98/37/ES
2006/95/ES, 2002/95/ES, 2002/96/ES, 89/336/ES, 2000/14/ES
Datum: 02.02.2007
MODENA (I)
Stefano Reverberi
Generální ředitel
OVERENSSTEMMELSESERKLÆRING
NO
Vi erklærer på eget ansvar at dette
produktet er i overensstemmelse med
følgende normer eller standarder:
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
i henhold til bestemmelsene i direktivene:
98/37/EC
2006/95/EC, 2002/95/EC, 2002/96/EC, 89/336/EC, 2000/14/EC
Dato: 02.02.2007
Modena (I)
Stefano Reverberi
Daglig leder
ΔΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ EL
Δηλώνουμε, αναλαμβάνοντας πλήρη ευθύνη αυτής
της δήλωσης, ότι το προϊόν συμμορφώνεται με τους
παρακάτω κανονισμούς και τα αντίστοιχα έγγραφα
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
με βάση τις προδιαγραφές των Οδηγιών:
98/37/EK
2006/95/EK, 2002/95/EK, 2002/96/EK, 89/336/EK, 2000/14/EK
Ημερομηνία: 02/02/2007
Μόντενα (I)
Stefano Reverberi
Managing Director
DICHIARAZIONE DI CONFORMITÀ IT
Dichiariamo, assumendo la piena responsabilità
di tale dichiarazione, che il prodotto è conforme
alle seguenti normative e ai relativi documenti
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
in base alle prescrizioni delle direttive:
98/37/CE
2006/95/CE, 2002/95/CE, 2002/96/CE, 89/336/CE, 2000/14/CE
Data: 02/02/2007
MODENA (I)
Stefano Reverberi
Managing Director
DECLARATION OF CONFORMITY EN
We declare under our sole responsibility that this
product is in conformity with the following
standards or standardized documents
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
In accordance with the regulations:
98/37/EC
2006/95/EC, 2002/95/EC, 2002/96/EC, 89/336/EC, 2000/14/EC
Date: 02/02/2007
MODENA (I)
Stefano Reverberi
Managing Director
DEKLARACJA ZGODNOŚCI PL
Deklarujemy z pełną odpowiedzialnością,
że wyrób ten jest zgodny z następującymi
normami i dokumentacją normalizacyjną
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
zgodnie z przepisami:
98/37/WE
2006/95/WE, 2002/95/WE, 2002/96/WE,89/336/WE,2000/14/WE
Data: 02/02/2007
MODENA (I)
Stefano Reverberi
Dyrektor zarządzający
STANDARDIENMUKAISUUSTODISTUS
FI
Todistamme ottaen täyden vastuun,
että tuote on seuraavien standardien
ja vastaavien asiakirjojen mukainen
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
seuraavien direktiivien mukaan:
98/37/EY
2006/95/EY, 2002/95/EY, 2002/96/EY, 89/336/EY, 2000/14/EY
Pvm: 02.02.2007
Modena (I)
Stefano Reverberi
Toimitusjohtaja
EG-VERKLARINGVAN OVEREENSTEMMING
NL
Bij dezen verklaren wij onder volledige eigen
verantwoordelijkheid dat het product
overeenstemt met het volgende normenstelsel
en de bijbehorende documenten
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
op grond van de voorschriften van de volgende richtlijnen:
98/37/EG
2006/95/EG, 2002/95/EG, 2002/96/EG, 89/336/EG, 2000/14/EG
Datum: 02/02/2007
MODENA (I)
Stefano Reverberi
Managing Director
DECLARACIÓN DE CONFORMIDAD ES
Declaramos, asumiéndonos la plena responsabilidad al
respecto, que el producto cumple con lo establecido por
las siguientes normativas y relativos documentos:
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
sobre la base de lo dispuesto por las directivas:
98/37/CE
2006/95/CE, 2002/95/CE, 2002/96/CE, 89/336/CE, 2000/14/CE
Fecha: 02/02/2007
MÓDENA (I)
Stefano Reverberi
Managing Director
KONFORMITÄTSERKLÄRUNG DE
Wir erklären in alleiniger Verantwortung,
dass das Produkt den folgenden Normen
und normativen Dokumenten entspricht:
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
gemäß den Bestimmungen der Richtlinien:
98/37/EG
2006/95/EG, 2002/95/EG, 2002/96/EG, 89/336/EG, 2000/14/EG
Datum: 02.02.2007
MODENA (I)
Stefano Reverberi
Managing Director
IZJAVA O SKLADNOSTI SL
Na lastno izključno odgovornost izjavljamo,
da je izdelek v skladu z naslednjimi standardi
ali standardiziranimi dokumenti
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
v skladu s predpisi:
98/37/ES
2006/95/ES, 2002/95/ES, 2002/96/ES, 89/336/ES, 2000/14/ES
Datum: 02/02/2007
MODENA (I)
Stefano Reverberi
Direktor
FÖRSÄKRAN OM CE-ÖVERENSSTÄMMELSE
SV
Vi försäkrar på eget ansvar att denna produkt
är i överensstämmelse med följande lagar
eller standarder:
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
enligt kraven i direktiven:
98/37/EG
2006/95/EG, 2002/95/EG, 2002/96/EG, 89/336/EG, 2000/14/EG
Datum: 2007-02-02
Modena (I)
Stefano Reverberi
Verkställande direktör
KONFORMITETSERKLÆRING DA
Vi erklærer under almindeligt ansvar,
at dette produkt er i overensstemmelse
med følgende normer eller standarder:
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
i henhold til bestemmelserne i direktiverne:
98/37/EF
2006/95/EF, 2002/95/EF, 2002/96/EF, 89/336/EF, 2000/14/EF
Dato: 02.02.2007
Modena (I)
Stefano Reverberi
Adm. direktør
DECLARAÇÃO DE CONFORMIDADE PT
Declaramos, assumindo a plena responsabilidade por
tal declaração, que o produto está em conformidade
com as seguintes normas e relativos documentos
EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
com base nas prescrições das directivas:
98/37/CE
2006/95/CE, 2002/95/CE, 2002/96/CE, 89/336/CE, 2000/14/CE
Data: 02/02/2007
MODENA (I)
Stefano Reverberi
Managing Director