ansio VENUS Parts list manual

ANSIO 1320 (M21v01)
1
PTC CERAMIC TOWER HEATER
VENUS
Instruction and Operating Manual
THANK YOU
We thank you for purchasing our product.We understand that this purchase represents
your trust in us. We are grateful for this and assure you that we aspire to deliver the
best value to you in return. We are proud of our creation and take every precaution to
avoid problems. Despite this, sometimes a product might reach you with a defect. If
this happens, our responsive customerservices team will be able to assist you towards
a quick resolution. So, do not hesitate to contact us regarding any aspect of your
purchase.
This product is only suitable for well insulated spaces or occasional use.
NOTE: Always place the Venus Heater in a vertical position as shown.

ANSIO 1320 (M21v01)
2
This heater is for residential use only.
It is not intended to be used in commercial, industrial or agricultural settings.
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL,
OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT
YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION.
FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN
PERSONAL INJURY AND/OR PROPERTY DAMAGE!
IMPORTANT SAFEGUARDS
1. WARNING: IN ORDER TO AVOID OVERHEATING, DO
NOT COVER THE HEATER.
2. Before using always check and ensure that the supply cord
is not damaged.
3. If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
4. This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instructions concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
5. The heater must not be located immediately below a socket-
outlet.
6. Do not use this heater in the immediate surroundings of a
bath, a shower or a swimming pool.
7. CAUTION —Some parts of this product can become
very hot and cause burns. Particular attention has to be
given where children and vulnerable people are
present.

ANSIO 1320 (M21v01)
3
ADDITIONAL SAFETY INFORMATION
•To reduce the risk of fire, electrical shock or personal injury, always follow these
important safety instructions and warnings.
•Faulty wall outlet connections may cause the wall outlet to overheat. Be
sure that heater plug fits tightly into outlet before each use. During use,
check to make certain the heater plug is not overheating. If necessary, have
a qualified electrician check and/or replace the wall outlet. In case of
overheating or any other malfunctioning of the heater, please contact us
for further assistance.
•Some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present.
•To reduce the risk of fire, electric shock and personal injury, DO NOT attempt to
remove, replace, repair or tamper with the originally supplied plug.
•ALWAYS turn OFF and unplug the power cord when servicing, cleaning or
moving the heater.
•DO NOT run the power cord under carpeting. Do not cover cord with throw rugs,
runners, or similar coverings. Do not route cord under furniture or appliances.
Arrange the power cord away from traffic area and where it will not be tripped
over.
•DO NOT depend on the on/off switch as the sole means of disconnecting power
when servicing or moving the heater. Always unplug the power cord. Always turn
off and unplug heater before leaving the area. Never leave children unattended
when the heater is on or plugged in.
•DO NOT block or tamper the heater in any manner while it is in operation.
•DO NOT insert fingers or foreign objects to enter any ventilation as it may cause
an electric shock, fire and can damage the heater.
•DO NOT use this heater in the immediate surroundings of a bath, a shower, a
swimming pool, etc.
•DO NOT place the heater on soft surfaces like a bed as the openings may
become blocked. Always place the heater in a flat, even surface.
•DO NOT use the heater outdoors.
•Keep combustible materials, such as bedding, pillows, furniture, papers, clothes
and curtains at least 5 feet (1.5 m) away from the heater.
•DO NOT use this heater in areas where flammable liquids or vapours are used,
stored or are present, including paints, gasoline, varnishes, floor refinishing
products or solvents.
•Make certain that the room is equipped with a working smoke detector.
WARNING

ANSIO 1320 (M21v01)
4
TECHNICAL SPECIFICATIONS
MAX POWER: 2000W
VOLTAGE: 220-240V / 50 Hz
GUARANTEE
This product comes with standard 1 Year Warranty against all manufacturing defects.
In addition, register your purchase at www.ansio.co.uk within 15 days, and you
can get an additional one year FREE Extended Warranty. Terms and conditions
apply. Visit our website for more info.
This guarantee is invalid if the product is found to have been abused or tampered
with in any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be
returned to us without prior permission.
This guarantee does not affect your statutory rights.
This appliance is intended for household use only and NOT for commercial or
industrial use.
COMPONENTS OF THE HEATER

ANSIO 1320 (M21v01)
5
NOTE
There may be traces of smoke or odour arising from the heating coil when the heater
is first operated. This is expected and will quickly fade away and will not re-occur. If
the smoke or bad odour persists, do not use the heater and contact us for assistance.
BEFORE USING THE HEATER
1. Check if the power cord is in good condition.
2. Ensure that the heater is connected to an appropriate power socket in accordance
with the local regulations.
3. Always place the heater on a flat surface. The tip over feature will turn the heater
off if the heater is placed on an uneven surface or if the heater is accidentally
knocked off.
OPERATING INSTRUCTIONS
1. Insert the plug into the power socket and turn the switch ON.
2. The power selection knob will by default be in the OFF position at the centre.
3. From the OFF position, turn the power selection knob clockwise tochoose between
one of the following modes:
LO Power Mode:
The heater operates at 1200 W without oscillation.
HI Power Mode:
The heater operates at 2000 W without oscillation.
4. From the OFF position, turn the power selection
knob counter- clockwise to choose between one of
the following modes.
LO & OSC Mode
The heater operates at 1200 W with oscillation.
HI & OSC Mode
The heater operates at 2000 W with oscillation.
5. Turn the Temperature Control Knob to adjust the heating to the required level.
Note: The temperature control knob acts as a thermostat. In the event of
overheating, the heater will be turned OFF automatically.

ANSIO 1320 (M21v01)
6
SAFETY PROTECTION FEATURES
1. Overheat protection feature: When the temperature of the heater is too high, the
thermostat will automatically turn the heater OFF. When the heater cools down
completely, it can be used normally. Improper usage of the heater, dusty
environment etc. can cause this. The heater needs to be cooled down completely
and can be re-used as normal.
2. Accidental Tip-Over protection feature: When the heater is accidentally tipped
over, the safety tip-over protection feature will automatically cut the power off.
When the heater is placed in an upright position on an even surface, it can then be
used normally.
3. Anti-frost function: When the machine is on, turn the Temperature Control knob
to the “MIN” position, and whenever the room temperature drops to 0-5ºC, the
heater will automatically turn on. When the room temperature is over 5ºC, the fan
heater will automatically turn off.
PILOT LIGHT
The heater has a pilot light which illuminates whenever the heater is plugged in and
turned ON. The light will continue to glow even if the safety feature turns OFF the
heater in the event of overheating. This helps you to be aware that the heater is still
in operation and is controlling the room temperature.
CLEANING AND MAINTENANCE
Before attempting to clean this heater, always ensure that the power plug is
removed, and the heater is cooled down completely.
1. Accumulated dust must be removed from the heater with a soft cloth. Wipe the
exterior surface of the heater with a cloth moistened (not dripping wet) with a
solution of mild detergent and water. Dry the heater thoroughly with a soft dry cloth
before operating it.
2. Store heater in a clean and dry place when not in use.
3. Do not scrap the surface of the heater with sharp tools. This is to avoid the surface
getting rusty by damaging the paint coating.
4. The fan motor is lubricated by the factory and will require no further lubrication.
5. No other user maintenance is required or recommended.
NOTE: Portable electric heaters are designed to be a supplementary heating source.
They are not intended to be the main source of heating.

ANSIO 1320 (M21v01)
7
TROUBLESHOOTING
Problem
Possible Cause
Solution
When the power
is turned ON, the
heater does not
work
The plug may not be
inserted well.
Check whether the plug is
properly inserted into the
receptacle. Alternatively,
ensure that the power
receptacle is fully
functional or try another
plug socket.
When the power
is turned ON, the
heater does not
work
Power selector knob is in
the OFF position
Check if the power
selector knob is in the
OFF position. Turn it
clockwise/ anti-clockwise
to a desired setting for the
heater to turn ON. Adjust
the temperature control
knob to the required
heating level.
The heater
suddenly stops
working
The temperature exceeds
the threshold of the
thermal cut-off; hence the
heater is turned OFF
automatically.
Cool the heater down
completely before re-use.
The heater
suddenly stops
working
The heater is tipped over
and the safety tip-over
protection feature has
turned the heater OFF.
Place the heater upright in
an even surface and
restart the heater.
The heater shuts
off repeatedly or
gets over heated
or any other
malfunctioning of
the heater
Dust accumulation inside
the heater
Clean the heater. Refer to
“Cleaning and
maintenance” section.

ANSIO 1320 (M21v01)
8
WASTE DISPOSAL
●This item must not be disposed of with household waste. Please
recycle where facilities exist. In the interests of health, safety and the
environment, please check with your Local Authority for recycling
advice.
●By ensuring that you dispose of your old electrical and electronic
equipment according to The European Directive 2012/19/EU on Waste Electrical
and Electronic Equipment (WEEE), you are helping to preserve our natural
resources. Registration Number: WEE/MM6674AA. For your nearest disposal
facility, visit www.recycle-more.co.uk
This manual suits for next models
1
Table of contents
Other ansio Heater manuals