Antik EX-5108 User manual

USER MANUAL
EX-5108
8-Way H.264 HD/SD Encoder

01 Notice
03 Before Using the Device
04 1 Overview
04 2 Features
05 3 Technical Specifications
06 4 Ordering Information
07 5 Block Diagram
07 5.1 TS/IP “Full Duplex” mode (EX-5108)
07 5.2 TS/IP “Multiple Output” mode (EX-5108)08
08 6 Front panel and rear panel instructions
08 6.1 Front panel
09 6.2 Rear panel
10 7 Control with Front Panel
10 7.1 Overview of the Menu
10 7.2 Description of menu
11 7.2.1 Status
12 7.2.2 Configuration
17 7.2.3 System
18 8 Control with Web Server
18 8.1 Status
19 8.2 Encoder
21 8.3 TS/IP
25 8.4 MUX
27 8.5 System
29 9 Installation
Contents

1
www.antiktech.com
Notices
COPYRIGHT (Copyright © 2014 Beijing Jaeger Communication Electronic Technology Co., Ltd.)
Not to be copied, used or translated in part or whole without Beijing Jaeger prior consent in writing
except approval of ownership of copyright and copyright law.
WARRANTY
This warranty does not cover parts which may become defective due to misuse of the information
contained in this manual.
Read this manual carefully and make sure you understand the instructions provided. For your safety,
be aware of the following precautions.
WARNING! IMPORTATNT SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
WARNING
•To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
•To avoid explosion danger, do not dispose of batteries in an open fire.
CE MARK FOR EUROPEAN HARMONISED STANDARDS
The CE mark which is attached to these products means it conforms to EMC Directive
(89/336/EEC) and Low Voltage Directive (73/23/EEC).
IMPORTANT INFORMATION
Please retain the original packaging, should it be necessary at some stage to return the device.
Disposal of Old Electrical and Electronic Equipment (Applicable in the European Union and
other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be
treated as household waste. Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate
waste handling of this product. The recycling of materials will help to conserve natural
resources. For more detailed information about recycling of this product, please contact
your local Civic Office, your household waste disposal service, or the shop where you
purchased the product.

2
www.antiktech.com
COPYRIGHTS
Television programs, movies, video tapes, discs, and other materials may be copyrighted.
Unauthorized recording of copyrighted material may be against the copyright laws in your region.
Also, use of this product with cable television transmissions may require authorization from the
cable television operator or transmitter/owner.
VENTILATION
•Do not expose the product to high temperatures, such as placing it on top of other product that
produce heat or in places exposed to direct sunlight or spot lights.
•The ventilation slots on top of the product must be left uncovered to allow proper airflow into the
device.
•Do not stand the product on soft furnishings or carpets.
•Do not stack electronic equipment on top of the product.
•Do not place the product in a location subject to extreme changes in temperature. The
temperature gradient should be less than 10 degrees C/hour.
•Place the product in a location with adequate ventilation to prevent the build-up of heat inside the
product. The minimum ventilation space around the device should be 7 cm. The ventilation should
not be impeded by covering the ventilation openings with items, such as newspapers, table cloth,
curtains, etc.
POWER SOURCES
•The product is not disconnected from the AC power source (mains) as long as it is connected to
the power outlet or wall socket, even if the product is turned off.
•If the product will not be used for a long period of time, disconnect it from the AC power outlet or
wall socket.

3
www.antiktech.com
Before Using the Device
Thank you for purchasing the EX-5108 8-Way H.264 HD/SD Encoder. This User Manual is written
for operators/users of the EX-5108 to assist in installation and operation. Please read this user
manual carefully before installation and use of the device.
FOR YOUR SAFETY
This equipment is provided with a protective earthing ground incorporated in the power cord. The
main plug shall only be inserted in a socket outlet provided with a protective earth contact. Any
interruption of the protective conductor, inside or outside the device, is likely to make the device
dangerous. Do not remove the covers of this equipment. Hazardous voltages are present within this
equipment and may be exposed if the covers are removed. Only Beijing Jaeger trained and
approved service engineers are permitted to service this equipment.
The supplied AC power cable must be used to power the device. If the power cord becomes
damaged it must be replaced. No operator serviceable parts inside. Refer servicing to Beijing Jaeger
trained and approved service engineers. For the correct and safe use of the device, it is essential
that both operating and servicing personnel follow generally accepted safety procedures in addition
to the safety precautions specified in this manual. Whenever it is likely that safety protection is
impaired, the device must be made in-operative and secured against unintended operation. The
appropriate servicing authority must be informed. For example, safety is likely to be impaired if the
device fails to perform the intended measurements or shows visible damage.
WARNINGS
•The mounting environment should be relatively dust free, free of excessive vibration and the
ambient temperature between 0C° to 40C°. Relative humidity of 20% to 80% (non-condensed) is
recommended.
•Avoid direct contact with water.
•Never place the equipment in direct sunlight.
•The outside of the equipment may be cleaned using a lightly dampened cloth. Do not use any
cleaning liquids containing alcohol, methylated spirit or ammonia etc.
•For continued protection against fire hazard, replace line fused only with same type.
•Air intake for cooling is achieved via holes at the side of the device and the fans inside. The air
flow should not be obstructed. Therefore, the device has to be placed on a flat surface, leaving
some space at the sides of the device.
•When in operation, the internal temperature should not exceed the limit of 70C°.

4
www.antiktech.com
EX-5108Series 8-Way H.264 HD/SD Encoder
1 Overview
EX-5108 is a series of high density real-time H.264 HD/SD Encoders that can support up to eight High
Definition (HD)A/V signals compressing and encoding simultaneously. These A/V signals can be fed into
the device via 8x HDMI or 8x SDI input ports as different factory options. The encoded streams can be
then remultiplexed and output over its GbE IP and ASI ports. All models support Time Base Correction
(TBC) to ensure the audio and video synchronization, the features necessary for the professional TV
signal flow. The series provide two TS/IP operation modes. The first is “Full Duplex”, which allows one
MPTS or SPTS inputted over 1 multicast/unicast to make up a new MPTS with local encoders, then
sends out the new one over 1 multicast/unicast. In the second mode “Multiple output” which delivers up
to 9 streams over IP. There are 8 un-stuffed SPTS (lower bit rate but less PCR accurate than normal
SPTS, from local encoders) and 1 MPTS (from internal reMultiplexer) over the IP with different Unicast or
Multicast IP addresses. EX-5108 allows user to configure, monitoring and manage over the informative
front panel and keypad, or Web interface, or SNMP based management software from 3rd party. This
Encoder family presents brilliant picture quality, high density design, high stability system architecture,
and the hot-swappable power supply.
2 Features
Compile with H.264/AVC H[email protected]
MPEG1 Layer II, MPEG2 AAC-LC, MPEG4 AAC-LC audio compression (see ordering information)
8-way real time encoder with re-multiplexed integrated
Built-in re-Mux accepts up to 10 SPTS/MPTS (8 from local encoders, 2 from external input over IP and
ASI)
1 ASI input (for daisy chain) & Redundant ASI output
Full duplex Gigabit TS over IP I/O (under Full duplex operation mode)
Up to 9 multicast/unicast output (under Multiple-channle operation mode)
VBR and CBR encoding mode
Free resolution downscale at same frame rate
SNMP & HTTP WEB
Redundant Power Supplies
19” x 1 U EIA standard chassis

5
www.antiktech.com
3 Technical Specifications
Video input & compression
Number of input ports
HDMI x 8 or HD-SDI x 8
Compression Standard
H.264/AVC H[email protected]
Video Sampling Format
4:2:0, 8-bit, YCbCr
Video Encoding Bit Rate
2~30Mbps for each channel
Video Resolution &
Recommended Bit Rate
1080p（1920×1080）@ 59.94 Hz，50 Hz：SMPTE296M: 6~30Mb/s
1080i（1920×1080）@25Hz,29.97Hz,30Hz:SMPTE274M: 6~24Mb/s
1080i（1440×1080）@25Hz,29.97Hz,30Hz:SMPTE274M: 5~24Mb/s
720p（1280×720）@50Hz,59.94Hz,60Hz:SMPTE296M: 4~24Mb/s
480i（720×480）@29.97Hz:SMPTE656M: 2~10Mb/s
576i（720×576）@25Hz: SMPTE656M: 2~10Mb/s
Other Video Resolution
Free resolution downscale at same frame rate
Aspect Ratio
4:3/16:9 Selectable
Audio Input & compression
Input
HDMI or SDI Embedded audio
Audio Compression
MPEG1 Layer II, (MPEG2 AAC-LC, MPEG4 AAC-LC option for EX-5108)
Sampling Rate
48KHz
Compression Bit Rate
32~192Kbps(Mono), 64~384Kbps(Stereo), 128~512Kbps(AAC LC)
DVB-ASI Input
Interface
BNC Female, 75Ω
Maximum Input Bit rate
100 Mb/s
Data Transfer type
Byte
Packet Length
188 or 204 Bytes
Signal Level
200 ~ 880mVp-p
DVB-ASI Output
Interface
BNC Female, 75Ω
Max. Effective Data Rate
120 Mb/s
Data Transfer type
Byte
Packet Length
188 or 204 Bytes
Signal Level
800±80mV
Gigabit TS_over_IP (Full Duplex Mode)
Standard
IEEE 802.3, 10/100/1000 Base-T, Full Duplex
Number of Multi/Unicast
x 9
Max. Effective Bit Rate
80Mb/s
Data Protocol
UDP or RTP, SPTS or MPTS
Control Protocol
ICMP, ARP, IGMPv2

6
www.antiktech.com
Gigabit TS_over_IP Output (Multi-Channel IPTV Mode)
Standard
IEEE 802.3, 10/100/1000 Base-T,
Max. Effective Bit Rate
200Mb/s
Data Protocol
UDP or RTP, SPTS or MPTS
Control Protocol
ICMP, ARP, IGMPv2
Rear Panel
ASI In
1 x BNC Female, 75Ω
HD-SDI In
8 x BNC Female, 75Ω (EX-5108)
HDMI In
8 x HDMI Male, 75Ω (EX-5108 )
ASI Out
2×BNC Female, 75Ω(1 Backup)
Front Panel
Control
1×RJ-45, 10/100 Base-T
TS/IP
1× IP (GbE), RJ-45, 10/100/1000 Base-T
Display
2 x 20 LCD Display
Others
Power Supply
AC90~260V 50/60Hz
Operating Temperature
0 ~ 45℃
Storage Temperature
-10 ~ 60℃
Operation Humidity
10 ~ 90%, (Non-condensed)
4 Ordering Information
Model
Function
EX-5108 -H
EX-5108 -H
EX-5108 -S
EX-5108 -S
Input
HDMI
x 8
x 8
HD-SDI (BNC)
x 8
x 8
ASI (BNC)
●
●
●
●
TS/IP (under full
duplex mode)
●
●
●
●
Output
ASI (mirrored)
x 2
x 2
x 2
x 2
TS/IP (GbE)
●
●
●
●
AAC-LC Audio Support
●
●
Alarm
●
●
●
●
Control
●
●
●
●
RS-232
●
●
●
●

7
www.antiktech.com
5 Block Diagram (with different applications)
5.1 TS/IP “Full Duplex”mode (EX-5108 -H/–S)

8
www.antiktech.com
A3
A4
5.2 TS/IP “Multiple Output”mode (EX-5108 -H/S)
6 Front panel and rear panel instructions
6.1 Front panel
A1 Status LEDs Power: green when power is on, red when one of the power supply unit
malfunction
Warning: red when function faulty
Alarm: red when function critical
A5
A7
A6
A2
A1

9
www.antiktech.com
B1
B2
B3
B3
B4
B5
B1
B2
B3
B3
B4
B5
B6
B6
A2 Encoder Status Encoder 1~8 working status, green light indicates the corresponding
encoder module is under working, red when the corresponding encoder
module malfunction or stop or input is invalid
A3 VFD Panel
A4 Keypad 6 keys for local control
A5 USB Used to upgrade software version of this device
A6 Management Ethernet (10/100 LAN) control port
A7 TS/IP TS over IP I/O port
6.2 Rear panel of EX-5108
EX-5108 -S
EX-5108 -H
B1 ASI IN ASI input interface
B2 ASI OUT 2 ASI output interface (output in mirror)
B3 Digital Audio Video IN SDI/HDMI input interface
B4 RS232 Reserved for factory use
B5 Alarm Alarm relay interface
B6 Power Socket AC Power Input

10
www.antiktech.com
7 Control with Front Panel
With the keypad and display panel on the front panel, user can configure the device locally.
7.1 Overview of the Menu
Power on the device and wait for initialization complete, the Local IP address will be displayed on the VFD
panel. Press〔ENTER〕to get into the main menu.
(1) Status: show the status of the device
(2) Configuration: Configure and monitor parameters of encoding/transcoding
(3) System: Configure the local settings of the device
7.2 Description of menu
The main menu items can be selected with the keypad. By pressing the [Enter], the user navigates to the
sub-menus, which are selected in the same manner.
Main Menu
Status
Configuration
System
Input
Bit
Rate
Input
Format
Format
Refresh
TS/IP
Status
(Full
Duplex/
Multiple
Output)
Encoder
Remux
TS/IP
(Mode:
Multiple
Output/
Full
Duplex)

11
www.antiktech.com
7.2.1 Status
Sub-Menu
Sub-menu
Parameter
Description
Factory Default Value
Input Bit Rate
Encoder 1 Bit Rate
Display encoder 1 bit rate
Encoder 2 Bit Rate
Display encoder 2 bit rate
Encoder 3 Bit Rate
Display encoder 3 bit rate
Encoder 4 Bit Rate
Display encoder 4 bit rate
Encoder 5 Bit Rate
Display encoder 5 bit rate
Encoder 6 Bit Rate
Display encoder 6 bit rate
Encoder 7 Bit Rate
Display encoder 7 bit rate
Encoder 8 Bit Rate
Display encoder 8 bit rate
ASI Input Bit rate
Display the input ASI signal bit rate
TS/IP Input Bit Rate
Display the TSoverIP input bit rate
Input Format
Video 1 Input Format
Display the video format of input port 1
Video 2 Input Format
Display the video format of input port 2
Video 3 Input Format
Display the video format of input port 3
Video 4 Input Format
Display the video format of input port 4
Video 5 Input Format
Display the video format of input port 5
Video 6 Input Format
Display the video format of input port 6
Video 7 Input Format
Display the video format of input port 7
Video 8 Input Format
Display the video format of input port 8
Format
Refresh
Yes/No
Select to refresh the input video format
TS/IP Status
(Full Duplex)
Link Status
Display IP link status:10M/100M/1000M
IP Out Status
Display IP out UDP packet/s
Display IP out column FEC packet/s
Display IP out row FEC packet/s
IP In Status
Display IP in lock status and lock bitrate
Display IP in protocol
Display IP in mode of column FEC and row FEC
Display IP in packets per UDP frame
Display IP in received TS frames
Display IP in fixed RTP frames
TS/IP Status
(Multiple
Output)
Link Status
Display IP link Status:
10M/100M/1000M/Disconnect

12
www.antiktech.com
7.2.2 Configuration
Sub-Menu
Sub-menu
Parameter
Description
Factory Default Value
Encoder
Encoder
Encoder Select
Encoder Select:
Encoder 1: the encoder 1 is active for configuration
Encoder 2: the encoder 2 is active for configuration
Encoder 3: the encoder 3 is active for configuration
Encoder 4: the encoder 4 is active for configuration
Encoder 5: the encoder 5 is active for configuration
Encoder 6: the encoder 6 is active for configuration
Encoder 7: the encoder 7 is active for configuration
Encoder 8: the encoder 8 is active for configuration
Video Settings
Video Rate Ctl:
CBR: set constant bit rate mode
VBR: set variable bit rate mode
Input Video Format:
1920x1080i 29.97 / 1920x1080i 25 / 1440x1080i
29.97 / 1440x1080i 25 / 1280x720p 59.94 /
1280x720p 50 / 720x480i 29.97 / 720x576i 25 /
1920x1080p 59.94 / 1920x1080p 50
Video Bit Rate:
300~45000Kb/s: set the video bit rate
Aspect Ratio:
4:3: set video aspect ratio to 4:3
16:9: set video aspect ratio to 16:9
Video Rate Ctl: VBR
Input Video Format:
1920x1080i 29.97
Video Bit Rate: 3000Kb/s
Aspect Ratio: 4:3

13
www.antiktech.com
Encoder
Audio Settings
Audio Format:
MPEG1 Layer2: set the audio compression format
MPEG-1 Layer II
MPEG2 AAC-LC, MPEG4 AAC-LC can be selected
on EX-5108 series only
Audio Bit Rate: 32k bps /48k bps /56k bps /64k bps
/80k bps /96k bps /112k bps128k bps /160k bps /192k
bps /224k bps /256k bps /320k bps /384k bps
Audio Channel Mode:
Stereo: set stereo mode
Mono: set mono mode. NOTE: only Left audio
channel will be encoded
Audio Level:
+12dB~-17dB: set the gain of output volume
Mute: mute the output audio
Audio SDI EMB: (the menu is displayed on
EX-5108 -S only)
EMB1/EMB2/EMB3/EMB4: select the group of
embedded audio from input SDI signal
Audio Format: MPEG1
Layer2
Audio Bit Rate: 128 Kbps
Audio Channel Mode:
Stereo
Audio1 Level: 0dB
Audio SDI EMB:EMB1
Encoder Bit Rate
Encoder Bit Rate: 600~48000Kbps. set the output bit
rate of the selected encoder.
Note: Encoder bit rate must greater than the sum of
video bit rate + audio bit rate + PSI (150Kbps) +
buffering (100Kbps) + encoder error (150Kbps)
Encoder Bit Rate:
5000Kb/s
Advanced Settings
PMT PID: set PMT PID, valid range from 32 to 8190
decimal
Output PMT PID: 43
Video PID: set Video PID, valid range from 32 to
8190 decimal
Output Video PID: 4001
Audio PID: set audio PID, valid range from 32 to
8190 decimal
Output AudioPID:4002
PCR PID: set PCR PID, valid range from 32 to 8190
decimal
Output PCR PID:8004
Service PID: set Service PID, valid from 32 to 8190
decimal
Output Service PID:4000
Service Name: set the service name
Output Service Name:
Encoder Video
Scale:
Disable: video resolution is the same as input
Scale: Disable

14
www.antiktech.com
Enable: rescale the video resolution of the output
manually
Scale Vertical: set the resolution in vertical
576
Scale Horizontal: set the resolution in horizon
720
Null Filter:
On: filter away the null packages
Off: the service is stuffed with null packages
Note Null packet is essential for DVB applications,
don't remove them.
Null Filter: On
Encode Start out
Encode Start :
Enter=Yes: the settings will be applied to the selected
encoder, and start it to encode.
Exit=No: cancel the settings to the selected encoder,
which will keep the previous status
Remux
Remux
Program List
Program List: select the programs to remux. Click on
Enter to select, double click to cancel. (The
program(s) will be marked with an asterisk (*) once be
selected)
Encoder 1: select the SPTS from encoder 1
Encoder 2: select the SPTS from encoder 2
Encoder 3: select the SPTS from encoder 3
Encoder 4: select the SPTS from encoder 4
Encoder 5: select the SPTS from encoder 5
Encoder 6: select the SPTS from encoder 6
Encoder 7: select the SPTS from encoder 7
Encoder 8: select the SPTS from encoder 8
ASI Input: select the program(s) inputted via ASI
input port.
IP Input: select the program(s) inputted via IP input
port. (Note: this sub-menu is displayed only when the
IP I/O is configured as full-duplex mode.)
Bit Rate
Output Bit Rate: key in the bit rate of the newly
generated MPTS, valid range from 100~216000 Kb/s
Output Bit Rate:
38015Kb/s
Packet Size
188 Byte / 204 Byte
188 Byte
TS ID
TS ID: key in the TSID of the newly generated MPTS,
valid range from 0 to 65535 decimal
TS ID:00008
Remove CA
ON: remove the CA descriptors that are carried within
the inputted TS over ASI or IP
OFF: keep the CA descriptors
OFF

15
www.antiktech.com
Insert EIT
ON: insert EIT into the output stream, EIT data may
come from ASI or IP input port
OFF: don’t insert EIT into the output stream.
OFF
Output Program
Display the program list of the remux
TS/IP(Gigabit
Mode: Multiple
Output)
Channel 1~8
(the streaming
comes from Encoder
1~8
correspondingly.)
Uni/Multi IP Address: set the uni/multicast IP
address for the IP output 1~8
Uni/Multi UDP Port: set the port number, valid range
from 1~65535
Target MAC Address:
set the destination port number MAC Address
Gigabit Out Switch: ON/OFF: to switch on/off the
current channel
Uni/Multi IP Address:
238.069.070.001
Uni/Multi UDP Port:
01234
Target MAC Address:
00:00:24:56:12:67
Gigabit Out Switch: ON
Channel 9
(the streaming
comes from the
built-in Remux or
ASI input.)
Uni/Multi IP Address: set the uni/multicast IP
address for the IP output channel 9
Uni/Multi UDP Port: set the port number, valid range
from 1~65535
Target MAC Address:
set the destination port number MAC Address
Gigabit Out Switch: ON/OFF: to switch on/off the
current channel
MUX/ASI Out: set the source for IP output channel
9
Uni/Multi IP Address:
238.069.070.001
Uni/Multi UDP Port:
01234
Target MAC Address:
00:00:24:56:12:67
Gigabit Out Switch: ON
MUX/ASI Out: ASI
Gigabit Local
Gigabit Address: set the IP address of the IP port
IP Board IP
Address:10.10.80.60
Gigabit Subnet Mask: set the net mask of the IP port
IP Board Net
Mask:255.255.255.0
Gigabit Gateway: set the gateway of the IP port
IP Board
Gateway:10.10.80.1
Gigabit MAC Address: display the MAC address of
the IP port
IP Board MAC Address:
Protocol:
UDP: set UDP protocol to IP output
RTP: set RTP protocol to IP output
Protocol: UDP
TS Pkts Per UDP: set the number of TS packets that
can be carried by each UDP packet, valid range from
1~7
TS Pkts Per UDP: 7
Time To Live: set TTL to the output IP packets, valid
range from 1~255
Time To Live: 255
Type Of Service: Min Delay/Max Reliability/Max
Throughput/Min Monetary Cost/Normal
Type Of Service: Min
Delay

16
www.antiktech.com
Gateway MAC Address: set the MAC address of the
gateway under which the device is connected
Gateway MAC Address:
ff:ff:ff:ff:ff:ff
TS/IP
(Gigabit
Mode: Full
Duplex)
Gigabit Output
Gigabit Out Switch: Enable/Disable
Gigabit Out Switch: ON
Protocol:
UDP: set UDP protocol to IP output
RTP: set RTP protocol to IP output
Protocol: UDP
TS Pkts Per UDP: set the number of TS packets that
can be carried by each UDP packet, valid range from
1~7
TS Pkts Per UDP: 7
Time To Live: set TTL to the output IP packets, valid
range from 1~255
Time To Live: 1~255
Type Of Service: Min Delay/Max Reliability/Max
Throughput/Min Monetary Cost/Normal
Type Of Service: Min
Delay
Uni/Multi IP Address: set the destination IP address
Uni/Multi Address:
238.069.070.001
Uni/Multi UDP Port: set the destination port number,
valid range from 1~65535
Uni/Multi UDP Port:
01234
ProMPEG FEC Switch: Enable/Disable
ProMPEG FEC Switch:
Disable
ProMPEG FEC Mode:
1D,5x5/1D,5x20/1D,10x10/2D,5x5/2D,5x20/2D,10x10
ProMPEG FEC Mode :
1D,5x5
FEC Alignment:
Annex A/Annex B
FEC Alignment:
Annex A
Gigabit Local
Gigabit Address: set the IP address of the IP port
Gigabit Adress:
010.010.080.060
Gigabit Subnet Mask: set the net mask of the IP port
Gigabit Subnet Mask:
255.255.255.000
Gigabit MAC Address: display the MAC address of
the IP port
Gigabit Gateway: set the gateway of the IP port
Gigabit IP Gateway:
010.010.080.001
Gateway MAC Address: set the MAC address of the
gateway under which the device is connected
Gateway MAC Address:
ff:ff:ff:ff:ff:ff:ff
Gigabit Input
Uni/Multi Address: set the uni/multicast target
address of the IP input
Uni/Multi
Addres:238.069.070.002
Uni/Multi UDP Port: set the target port number of the
uni/multicast IP input, valid range from 1~65535
Uni/Multi UDP Port:
01234

17
www.antiktech.com
Gigabit Input
TS Clock Recovery:
Auto: it is suggested to set Auto when there is
accurate PCR carried by the inputted TS/IP
Fixed Rate: when fixed rate is selected, user has to
configure a bit rate to regenerate the TS clock. The
configured fixed bit rate has to be a little bit higher
than the bit rate of the inputted TS/IP.
TS Clock Recovery: Auto
7.3 System
System
Network Setting
IP Address: set the IP address of the device, valid
range from 0.0.0.0~255.255.255.255
IP Address: 10.10.70.48
Subnet Mask: set the net mask of the device, valid
range from 0.0.0.0~ 255.255.255.255
Net Mask: 255.255.255.0
Gateway: set the gateway of the device, valid range
from 0.0.0.0~255.255.255.255
Gateway: 10.10.70.1
MAC Address: to display the MAC address
Remote Setting
Trap IP Address: set the IP address of the SNMP
Trap server, valid range from
0.0.0.0~255.255.255.255
Trap IP Address:
10.10.70.25
Device Label
Device Label: user allows to rename the device,
press Enter and key in the name of the device, then
press Enter to confirm the setting or press Exit to
cancel.
Software Version
Software Version: display the software version
Factory Default
Factory Default:
Enter = Yes: press Enter to recall the factory default
settings.
Exit = No: press Exit to cancel
Note: the IP address of
the device is not reset to
the factory setting!
Machine Type
MAC Address: to Modify the MAC address
S/N: display the serial number of the device
Gigabit MAC Address: to Modify the Gigabit MAC
address
Detail Version: Display the detail version of
MCU,FPGA,LINUX OS
WEB Login ID
Edit Login ID: press Enter and key in the login ID
for WEB management
Default Login ID: root
WEB Login Password
Edit Login Password: press Enter and key in the
password for WEB management
Default Login Password:
12345

18
www.antiktech.com
System
Gigabit Mode
Gigabit Mode:
Gigabit Mode: Multiple
Output
Multiple Output: the IP I/O is configured as multiple
uni/multicast output mode, which delivers up to 10
streams over IP. There are 8 stuffed or un-stuffed
SPTS (lower bit rate but less PCR accurate than
normal SPTS, from local encoders) and two MPTS
from built-in remultiplexer and ASI input over the IP
with different Unicast or Multicast IP addresses.
Full Duplex: the IP I/O is configured as full duplex
mode, which allows only one MPTS or SPTS over IP
input and output in uni/multicast at the same time.
8. Control with Web Server
EX-5108 has an integrated web server. This web server allows the configuration and status requests with a
standard web browser. To operate a EX-5108, first make sure the Ethernet control port is well connected in
the network and could be pinged by the host PC, and then enter the IP address of the EX-5108 into the
browser, there will be a pop-up showed asking for login user and password. After login the device can be
operated. The default user name and password are respectively “root”and “12345”. The username and
password can be changed by user via front panel or via submenu under the system page. If the username and
password are forgotten, user have to set a new one via front panel.
8.1 Status
Via the status page, user can have an overview of the current status of the connected EX-5108.