Kessil A360W User manual

1. DO NOT use a power supply that is outside the
specifications. This is a fire hazard and may lead
to unit failure.
2. DO NOT use outdoors. This unit is intended for
indoor use only.
3. DO NOT expose unit to an extremely humid
environment or submerse unit in water. This may
lead to unit failure.
4. DO NOT place working illuminator in close contact
with any objects. This may cause objects to heat
up and the unit to overheat.
5. KEEP lens (H) away from sharp objects. Sharp
objects may break the lens and lead to unit failure.
6. DO NOT cover or place objects on the power
supply. Power supply should not be contained in
an airtight space.
SAFETY INSTRUCTIONS
INSTALLATION GUIDE
1. Remove contents from package.
2. Screw the hanging bolt (C) into the center hole.*
3. Hang the A360N / A360W 1 to 2 ft. above the object
to be illuminated.**
4. Connect power cord (A) to the specified DC power
supply (J).
5. Plug the power supply into an outlet with the correct
specifications (see product specifications for more
information).
6. Adjust the Light Intensity Control (I) and the Spectral
Tuning Control (D) to the desired setting. When set
fully to the left, the light is very close to Kessil Sky
Blue.The middle setting is very close to Kessil
Ocean Blue. Fully to the right is close to actinic blue.
7. The jacks beneath the controls can be connected to
an external 0~10V controller. Please consult your
controller’s owners manual for more information.
*The A360N / A360W may also be hung by mounting two metal
hooks (diameter of at least 2.5 mm and thread count of at least 6)
through its brackets (F).
** The A360N / A360W should only be installed on wood, acoustic
tile or other similar ceilings.
** For sufficient airflow, the intake and venting holes (E,G)
should be at least 12 in. from surrounding obstructions.
Kessil Lighting
A DiCon Brand
1689 Regatta Blvd, Richmond, CA 94804
[phone]
www.kessil.com
OWNER’S MANUAL
LED ILLUMINATOR
A360N
A360W
LED Aquarium Light
PRODUCT SPECIFICATIONS
Power Consumption
Input Voltage
Illuminator
90W MAX
19 VDC
Listed Power Supply
Input
Output 19 VDC, 4.74 A
100 - 240 VAC, 47 - 63 Hz, 1.5 A MAX
A 360N / A 360W
Kessil takes another leap forward in the Spectral Revolution
with the A360N / A360W Tuna Blue LED aquarium light.
Incorporating the latest 90W Dense Matrix LED platform,
A360 features a penetrating, tunable light that provides a
beautiful shimmer effect, boosts coral growth and color,
and can easily be tuned to emit a range of spectrums from
Sky Blue to Actinic Blend and every shade in-between.
PARTS DIAGRAM DC Power Supply
J
Power Cord
A
Hanging Bolt
C
External Controller Port (2)
K
Air Intake Holes
E
Bracket
F
Venting Holes
G
Spectral Tuning Control
D
Light Intensity Control
I
Lens
H
Gold Metal Hook
B

LED Aquarium Lighting
Problem
Light doesn’t
turn ON
Unit is
flickering
Make sure the unit is connected to the power
supply and the power supply is plugged into
an outlet with the correct specifications.
Make sure the power supply has the right
specifications.
Make sure the unit has not overheated by
operating at a room temperature above
100°F/40°C.
Make sure electrical power is available to the
AC outlet being used.
Make sure the power supply has the right
specifications.
Make sure the device is operating within the
specified operating temperature range. If unit
overheats, it will automatically shut down.
Make sure the fan is operating properly.
TROUBLESHOOTING GUIDE
Cause / Solution
Please make sure to perform maintenance before doing any
troubleshooting.
MAINTENANCE
1.Keep the air intake holes (E), venting holes (G), and fan
clear of dust. To clean the fan, unplug the unit and insert
the tip of a CO2dust blower (or similar dust blower) in one
of the venting holes (G) on the unit's outer shell. Hold and
spray. You can also gently vacuum out the light through
the venting holes.
2.Keep the lens (H) clean. If the lens becomes contaminated
with water, dust, or other particles, unplug the unit and
clean the lens with isopropyl alcohol. Wet a cotton swab or
a napkin in isopropyl alcohol, gently wipe the surface of
the lens, and let it dry.
P/N : 5870027
CONTROLLING MULTIPLE A360 LIGHTS
Multiple A360N and A360W lights can be controlled by either a single
external 0~10V controller or manually.
CABLES
Available cables (each sold separately):
• Control Cable (Please consult www.kessil.com for list of
available cables and compatible controllers)
• Unit Link Cable (6' male/male with 3.5mm stereo plug)
• Control Extension Cable (6' male/female with 3.5mm
stereo plug to 3.5mm stereo jack)
STARTING A CHAIN
Connect two or more lights with the Kessil Unit Link Cable,
as shown above.
CONTROL METHODS
There are two ways to control a chain of lights:
• With an external controller;
• Without external controller (Tuning Controls on first light
control all other lights in chain).
Should a longer cable be needed, the Kessil Control Extension
Cable may be used.
Each light has its own independent power supply. Any number
of lights can be daisy chained together without degradation of
signal. However, in longer chains a slight delay in response
may occur.
Tuning Controls are disabled when device senses input
cable.
Output
Unit Link Cable
Input
To next light Input from Controller
Spectral Tuning Control Light Intensity Control
Scan this code on your smart-
phone to learn more about Kessil
Visit Us
Kessil Lighting
A DiCon Brand
1689 Regatta Blvd, Richmond, CA 94804
[phone]
www.kessil.com