Anttron TMX160HD User manual

TMX160HD
HD encoder - DVB-T/C out
USER MANUAL VERSION 1.0

USER MANUAL
TMX160HD
PAGE 2
ANTTRON ©2020
1 - Safety considerations
1.1 CONNECTING TO THE MAINS SUPPLY
This product has to be connected to the mains supply. If there is the slightest doubt concerning the
type of connection available on the installation, please contact your supplier of electricity. Before car-
rying out maintenance operation or modification of the installation, the modulator has to be discon-
nected. Remark : only use the supplied power adaptor.
1.2 OVERVOLTAGE
An overvoltage on the mains supply,can cause shortcircuits or fire. Never overload the power lines.
1.3 LIQUIDS
This module should be protected from splashes. Please assure yourself that no containers containing
liquids are placed on this module. Also be aware of other persons splashing liquids on the module.
1.4 CLEANING
Disconnect the module before cleaning. Use only a humid cloth without solvant.
1.5 VENTILATION
In order to assure an adequate air circulation and to prevent overheating, the ventilation holes should
not be obstructed. The module may not be installed in a hermetically sealed environment. Other elec-
tronic products or heat producing items may not be placed upon or near the module.
1.6 ACCESSORIES
The use of accessories not manufactured by the manufacturer can cause damage to the module.
1.7 INSTALLATION OF THE MODULE
The module must be installed in a place well protected from direct sunlight. All measures have to be
taken to avoid installation in humid or sunny place.Do not install near heating elements or other devic-
es producing heat. Assure yourself that the module is placed at least 10 cm from other equipment with
is susceptible to electromagnetic radiation. Do not install the module on instable items. A fall can cause
physical or material damage.
2 - Technical specifications
Video input Input HDMI
Resolu on modes 480p -576p -720p - 1080i - 1080P
Compression H.264 – bitrate 5-15 Mb/s
Audio input Input HDMI
Sample Rate HDMI (32kHz / 44.1 kHz / 48 kHz)
Compression AAC-LC / MPEG1-L2– bitrate 128-384 Kb/s
DVB Processing Table inser on PAT, PMT, SDT, NIT
Confi gura on Channel/network name, SID, LCN, TSID, ONID, NID, versions, audio, video PIDs…
DVB-T output Output frequency / level 170-230 MHz + 470-862 MHz / > 82 dBμV
Constella on - FEC QPSK/16QAM/64QAM - 1/2, 2/3, 3/4, 5/6, 7/8
Guard interval 1/4, 1/8, 1/16, 1/32
Mode - MER 2K/8K - 34 dB
DVB-C output Output frequency/level 47-862 MHz / > 82 dBμV
Constella on - MER QAM16,32,64,128,256 / MER > 40 dB
Symbol rate up to 7000 kB/s
Power + consump on DC 2.1 mm connector +5V - 10 Wa s
Dimensions + weight LxWxH 150x130x35mm - 0.45 kg
EAN code TMX160HD 5420037691616

USER MANUAL
PAGE 3
ANTTRON ©2020
TMX160HD
3 - Description of the different elements
A1 Alphanumeric display
T1 SELECT button
T2 (UP) button
T3 (DOWN) button
C1 Power supply input (5V/2A)
C2 USB input (for programming the TMX160HD by PC)
C3 RF input
C4 RF output
C5 HDMI input
T1 T2
T3
A1
C1 C2 C3 C4C5
4 - Installation and quick menu
4.1 - Installation
Connect the audio and video source using a HDMI cable. Connect the RF input cable (if present)
and the RF output cable. If the RF input is not used, please connect a 75 ohm terminating resistor
to it. Once the modulator installed and the cables connected, please proceed connecting the power
supply to the modulator.
4.2 - Powering up and quick menu
Plug in the connector of the power supply. The display will show a red dot in the left uppercorner.
Once the modulator has booted correctly the display will show : St
With the buttons UP and DOWN, you can toggle between St(standard DVBT or DVBC) ch (chan-
nel) ,AT (attenuation) and ID (program id) .
Once selected the right option, press and hold the select button.
In standard mode the display will show the actually selected DVB standard (t or c). With the select
button pressed used up down keys to change the standard.
In channel mode, the display will show you the actual output channel. For instance 21
With the select button pressed use the up and down buttons to change the output channel.

USER MANUAL
PAGE 4
ANTTRON ©2020
In attenuation mode, with the select button pressed, the display will show the actual level of at-
tenuation at the the output for instance 00 . Keep the select button pressed and use the up or
down buttons to change this value (00 - 15).
In the last mode the program ID can be changed.
The selected values are automatically saved in the memory of the TMX160HD.
Once these settings made, the display on the TMX160HD will return to its standby state. The dis-
play shows one or two dots. One dot to indicate that power is applied to the unit. The second dot
to the right indicating that a HDMI source is connected to the unit.
4.3 - Return to factory settings.
To return to factory settings, power down the modulator. Now, with the UP button pressed, put the
power again to the modulator. Keep the UP button pressed ands wait until the mesage r5 appears
on the display. The modulator has returned to its factory settings.
TMX160HD
n
n
n
n
n
n
n
ni
ni
ni
ni
ni
n
n
i
i
i
n
n
i
i
i
i
i
i
n
n
i
i
t
t
t
t
t
t
t
t
t
t
t
t.
t
t
t
t
t
t
t
t.
t
t
t
t
t
t
t.
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t.
.
.
t
t
t
t
t
t
t
t
t
.
t
t
t
t
t
t
t.
.
t.
t
t
t
t
t
t
t.
.
t.
t
t
t
t.
.
t.
t.
.
t
t
t
t
t
t.
t
t
t
t.
t
t
t
t
t
t
.
t
t
t
t
t
t
t
t
t
.
.
t
t
t
t
t
t
t.
t
t
t
t
t
.
t.
.
.
t
.
t
t
t
t
.
.
t
t
t
.
.
.
.
.
t
t
t
.
t.
.
t
t
5 - Advanced settings using a PC
More, advanced settings of the TMX160HD can be changed using a PC.
First, please install the software TMHDIFace on your PC. You can download this software from our
internet site anttron.com
After installation of this software, connect the TMX160HD using a USB cable (not included) to your per-
sonal computer. Then launch the program TMHDIface.
On the display of the TMX160HD the message ()appears, indicating that the programming is now per-
formed through your PC. The following window appears on your screen.
Now, further parameters can be edited in the TMX160HD.