AnyDATA APE-540C User manual

APE-540C
(User Manual)
SW-APE-540C-UG-V0.3E
March 10, 2009

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™2/40
AnyDATA CDMA Module Series Reference Design Specification
Copyright © 2009 AnyDATA Corporation. All Rights Reserved.
Any part of this document may not be distributed, communicated, reproduced or transmitted in any form
or by any means, electronic or mechanical or otherwise, for any purpose, without the permission of
AnyDATA Corporation.
This document can be subjected to revision without further notice.
RF Exposure Warning:
The radiated output power of this device is below the FCC radio frequency exposure limits.
Nevertheless, the device should be used in such a manner that the potential for human contact
during normal operation is minimized. In order to avoid the possibility of exceeding the FCC
radio frequency exposure limit, human proximity to the antenna should not be less than 20cm.
§ 15.21 Information to user.
No changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Contact Address
AnyDATA.NET, Inc.(Korea)
DaeGo Bldg, 1591-10
Kwanyang-dong, dongan-gu,
Anyang City, Kyunggi-do Korea.
http://www.anydata.co.kr
E-mail: [email protected]
Rep:[phone]
Fax:[phone]

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™3/40
Contents
AnyDATA.NET CDMA Systems.................................................................................................................. 4
User Instruction.......................................................................................................................................... 5
Illustrate Instructions .................................................................................................................................. 6
LED............................................................................................................................................................ 7
Connecting Express Card to PC ................................................................................................................ 8
■Inserting/Removing Express Card ....................................................................................................... 8
System Requirements.............................................................................................................................. 11
■Check the operating condition ............................................................................................................11
Easy Wireless Net Installation and Uninstallation (In Windows 2000) ...................................................... 12
Easy Wireless Net Installation and Uninstallation (In Windows XP) ......................................................... 14
■Installing Easy Wireless Net and Driver............................................................................................. 14
■Uninstalling Easy Wireless Net and Driver ........................................................................................ 18
Easy Wireless Net Installation and Uninstallation (In Windows Vista) ...................................................... 20
■Installing Easy Wireless Net and Driver............................................................................................. 20
■Uninstalling Easy Wireless Net and Driver ........................................................................................ 24
Using Easy Wireless Net.......................................................................................................................... 26
■Main application interface.................................................................................................................. 26
■Connecting / Disconnecting the Internet ............................................................................................ 28
■Sending and Receiving SMS ............................................................................................................. 29
■Writing New Message .................................................................................................................... 30
■Viewing sent message ................................................................................................................... 32
■Viewing received or saved message..............................................................................................33
■Phonebook ........................................................................................................................................ 34
■Setting Environment .......................................................................................................................... 35
■[ About ] ......................................................................................................................................... 35
■[ Basic ].......................................................................................................................................... 36
■[ RUIM Card ]................................................................................................................................. 37
■[ Advance]...................................................................................................................................... 38
■[ User ] ........................................................................................................................................... 39
CDMA Q&A .............................................................................................................................................. 40

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™4/40
AnyDATA.NET CDMA Systems
Thank You for Purchasing the "Express Card".
APE-540C is slim-line Express Card with Plug & Play solution offering the most user-friendly wireless
Express Card available on 3G network.
With AnyDATA’s proven performance and reliability in EVDO (Rev. A) technology, it ensures high-
speed data connection at 1.8Mbps uplink and 3.1Mbps downlink
APE-540C is the next generation of wireless data card designed by AnyDATA to be compatible with
CDMA 850MHz networks supporting the higher data rates of up to 3.1Mbps using EVDO (Rev. A)
technology.

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™5/40
User Instruction
■Packet data communication fees
Contrary to the voice communication fees, you may pay the fees by actual data usage. Please
ask the service provider or A/S center for more detail.
<Note>
- Please be careful that data service rates may become high when performing communication
with large amount of data such as browsing the homepage and downloading data.
- Please check carefully, the data service rates for the International Roaming Data differ from
domestic data service rates.
■User authentication as Network Access
You may be required to enter User ID and Password to access the Internet. In this case, ask the
service provider or A/S center if you don’t know the ID and password.

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™6/40
Illustrate Instructions
Upper bottom
LED
Connector
Antenna
RUIM

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™7/40
LED
LED Action
Power
IDLE
BUSY

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™8/40
Connecting Express Card to PC
■Inserting/Removing Express Card
When you install the Express Card to PC for the first time, you need to have the driver installed first.
<Note>
- Check if the PC has the Express Slot.
- The Express Slot may be located differently from PC to PC.
■Inserting Method
1. Turn on the PC.
2. Insert the Express Card to the Express Slot of PC with LED facing down.

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™9/40
■Method 1: Removing the Express Card by pushing the button as indicated
1. Check the Express Card is disconnected.
<Note>
- Exit the Express Card utility if it is in use.
-
2. Push the Express Card softly as indicated, then it will be ready to remove easily.
3. Hold the sides of the Antenna and pull it out.

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™10/40
■Method 2: Removing Express Card by pushing it to the direction as indicated
1. Check the Express Card is disconnected.
<Note>
- Exit the Express Card utility if it is in use.
2. Push the Express Card softly as indicated, then it will be ready to remove easily.
3. Hold the sides of the Antenna and pull it out.

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™11/40
System Requirements
■Check the operating condition
Install and operate the program under the following operational environments:
Item Requirement
Laptop Laptop with Express Card / 34 slot compatible
OS Windows 2000 (SP4)
Windows XP (SP3)
Windows VISTA (SP1)
Memory 128Mb or more
Hard disk 50Mb or more available space
Display 800 x 600 dots or more recommended

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™12/40
Easy Wireless Net Installation and Uninstallation (In Windows 2000)
<Note>
- Express Card doesn’t support Plug & Play in Windows 2000 and installation should be executed
manually as described below.
Follow the steps to use Express Card for Windows 2000.
1. Install the Express Card to PC and verity if it is recognized properly as CD-ROM.
2. Open “My Computer”.
3. Click “AnyDATA” CD-ROM.
1) Double-click the “AnyDATA (H:)” or right-click and select “Open”.

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™13/40
4. Double-click the “StartCD.Exe”
<Note>
- Follow the step as indicated page 14, “Installing Easy Wireless Net and Driver” and page 18,
“Uninstalling Easy Wireless Net and Driver”.

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™14/40
Easy Wireless Net Installation and Uninstallation (In Windows XP)
■Installing Easy Wireless Net and Driver
1. Connect the modem to your PC with Express Card.
If the driver has not been installed in your PC yet, Modem package installer will install the driver
automatically. Otherwise if it still has not been installed, put the install CD in CD-ROM and run
StartCD.exe manually.
2. Select the desire language as shown below. Press button to proceed. By pressing
button, the installation of Easy Wireless Net Program will stop.
3. You can install Easy Wireless Net Program and modem driver by choosing the installing option.

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™15/40
4. Next window displays asking proper path for installing the program.
Default path is <C:\Program Files\Easy Wireless Net>

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™16/40
5. Press button for ending the program installation.
6. The computer needs to restart after the driver installation completed.
To restart the computer later, select “I want to manually reboot later”.
<Note>
- It is recommended to select “Reboot now”.
The device may not function properly if you select “I want to manually reboot later”

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™17/40
<Note>
- Connect the modem and PC`s Modem Slot, and check if the driver is installed properly in
<Device Manager>. See the followings to the location of <Device Manager>
[Start ▶Control Panel ▶System ▶Hardware Tab ▶Device Manager]
As shown in below with red boxed that shows <AnyDATA CDMA Express Card> and
<AnyDATA CDMA USB Serial 1/2 Device>, the driver has been successfully installed.

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™18/40
■Uninstalling Easy Wireless Net and Driver
1. [Start ▶Programs ▶Easy Wireless Net ▶Uninstall]
2. By pressing Uninstall button, EWN program will be uninstalled.

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™19/40
3. Click “Yes” to remove the modem driver.
4. Click “Yes”. Following screen will appear twice.
5. The computer must restart after the driver is uninstalled.

Manual for APE-540C
AnyTime AnyPlace AnyWireless Data Solutions™20/40
Easy Wireless Net Installation and Uninstallation (In Windows Vista)
■Installing Easy Wireless Net and Driver
1. Connect the modem to your PC with using Express Card.
If the driver has not been installed in your PC yet, Modem package installer will install the driver
automatically. Otherwise if it still has not been installed, put the install CD in CD-ROM and run
StartCD.exe manually.
2. Press button to proceed. By pressing button, the installation of Easy
Wireless Net Program will stop.
3. You can install Easy Wireless Net Program and modem driver by choosing the installing option.