AnyTone BT01 User manual

A1.221121
www.anytone.net

BT01
User Guide
Bluetooth Microphone

Precautions
Please read the following regulations carefully before using this
product. The following regulations will help you understand and
fulfill your obligations in the warranty terms.
1. Without permission, please do not try to disassemble or modify
the BT01 Bluetooth Microphone. The handling of the Bluetooth
Microphone by non-professionals may cause damage.
2. Please don't put the Bluetooth Microphone in a dusty or damp
place.
3. Please abide by the walkie-talkie usage rate of 1 minute
for transmission and 4 minutes for reception. Long-term
transmission or continuous use in high-power mode will cause
the AT-D578UV mobile radio to heat up.
4. Please charge the BT01 Bluetooth Microphone before using it.
5. Do NOT insert a micro SD card into the SD-card slot. BT01
microphone doesn't support the SD card use.
Thank you for purchasing the Anytone BT01 Bluetooth Microphone .
This product uses a dedicated master-slave Bluetooth module
to realize wireless talk and wireless operation settings for all
functions of the AT-D578UV DMR mobile radio. Combined with
the noise reduction function, it can effectively reduce background
noise and ambient noise to achieve high-definition intercom.

When you receive the BT01 microphone, please access the AT-
D578UV Menu-Setting-Device Info to check the version first,
make sure the radio is upgraded to the latest version to get the
BT-01 microphone working correctly. Reset must be done to the
radio after the firmware upgrade.
Latest firmware is available for download on https://www.anytone.
net/download page.
APPLICABLE MODELS
BT MODE CABLE MODE
AT-D578UV/
AT-D578UVIII
No GPS, No BT
AT-D578UV PRO/
AT-D578UVIII PRO
With GPS and BT
AT-D578UV PLUS/
AT-D578UVIII PLUS
With GPS and BT
Model
Name Firmware SCT3258 BT module Software
APRS+BT
board
AT-D578UV/
AT-D578UVIII
No GPS, No BT
D578UV Ver1.17
or higher
V2.01.07BF
or higher N/A N/A
AT-D578UV PRO/
AT-D578UVIII PRO
With GPS and BT
D578UV Ver1.17
or higher
V2.01.07BF
or higher
ET12_AQQX_
V10043
or higher
N/A
AT-D578UV PLUS/
AT-D578UVIII PLUS
With GPS and BT
D578UVII Ver2.04
or higher
V2.01.07BF
or higher
ET12_AQQX_
V10043
or higher
V1.06
or higher

CONTENTS
1.Accessories ..................................................................... 1
1.1 Supplied Accessories ................................................................ 1
1.2 Optional Accessories ................................................................. 1
2.Charge The Battery ......................................................... 1
3. Getting Started................................................................ 2
Indicator Instructions ....................................................................... 2
4. Basic Operation.............................................................. 3
4.1 Power ON .................................................................................. 3
4.2 BT MODE connect to AT-D578UV ........................................... 3
4.3 CABLE MODE connect to AT-D578UV .................................... 4
4.4 Power Off ................................................................................... 4
4.5 Adjust The Volume .................................................................... 4
4.6 Set Up VFO Frequency ............................................................. 5
4.7 Select a Channel ....................................................................... 5
4.8 Select a Zone ............................................................................ 6
4.9 Make a Call ................................................................................ 6
4.10 Receive a Call ......................................................................... 6
4.11 Noise Reduction function ......................................................... 6
4.12 Menu Operation ....................................................................... 7
4.13 Programmed Key ..................................................................... 8
5.Technical Specications............................................... 12
EU DECLARATION OF CONFORMITY ............................ 13

1
1.Accessories
2.Charge The Battery
Charging Instructions
1. Insert the USB plug of the charging cable into the power
adapter.
2. Plug the power adapter into the AC power outlet.
3. Insert the other end of the charging cable into the charging/
upgrade interface of the radio.
4. The red charging indicator of the BT01 Bluetooth Microphone is on.
5. When the red charging indicator of the BT01 Bluetooth
microphone goes out, the charging is completed.
Belt Clip
WWZZ-0005
4m Cable
SMX-0037
User's Manual
Adaptor 5V/1A
KGDY-0106
Cigarette lighter charger
(output 5V/1A, input 12V-48V)
CC-0026
USB-C charge cable
QT-0046
»USB Adaptor and Cigarette light charger must be 5V voltage
and ≥1A current output.
1.1-Standard Accessories
1.2-Optional Accessories

2
3.Getting Started
Indicator Instructions
Indicator Color Status
Left light red Transmit
Right light red Charge the battery
Right light green Receive
Right light red blinking Battery voltage is low
PTT
P2
P1
P3 MIC
Headset Jack
USB charge/
Firmware upgrade
Speaker
RJ45 connector
Indicator
UP POW DN

3
»In BT mode, DO NOT attach the 4meter cable to connect the
radio and BT01 microphone, it might cause strange behaviour.
4.Basic Operation
4.1-Power ON
Press the top [POW] button on microphone, the right green indicator
light on, later the screen displays "Select Port", press or to
choose the connect mode:
BT MODE: Connect the BT01 microphone to AT-D578UV mobile
radio through Bluetooth.
CABLE MODE: Connect the BT01 microphone to AT-D578UV
mobile radio through 4m cable.
Click on "confirm" to select the connect mode.
4.2-BT MODE connect to AT-D578UV
After select "BT MODE " on microphone, it will display BT NAME and
"NO DEVICE CONNECTED" when no radio is connected. In this
state, the BT pairing shall be done on AT-D578UV.
a. Enter into AT-D578UV radio Menu Bluetooth BT On/Off, set
it ON.
b.Switch to AT-D578UV radio Menu Bluetooth BT Pairing,
select "Seek BT".
c.AT-D578UV radio displays "Seeking BT", it will take some time
to do the pairing.
d.AT-D578UV radio displays "ALL DATA CHECKING", the display
content of the AT-D578UV radio will be mapped to the Bluetooth
microphone.
e.AT-D578UV radio displays "EXTERNAL BT MODE" on the
screen, the pairing is done. BT icon is showed on the BT01
display to indicate it is at BT mode.

4
»Once the BT pairing is done, the BT microphone will
automatically connect to AT-D578UV radio after reboot.
»In BT mode, the cross band repeater function is not available,
as the audio path is occupied by the BT function.
»In CPS Optional Setting BT BT shutdown RF, if you
set this function ON. AT-D578UV radio will be powered off/on
automatically when BT microphone is off/on.
4.3-CABLE MODE connect to AT-D578UV
After select "CABLE MODE" on microphone, it will display "NO
DEVICE CONNECTED" when no radio is connected.
Use the 4m cable to connect the microphone to radio, AT-D578UV
displays "ALL DATA CHECKING", the display content of the AT-
D578UV radio will be mapped to the Bluetooth microphone.
AT-D578UV radio displays "EXTERNAL CABLE MODE" on the
screen, BT01 microphone is able to access the radio menu and do
communications now.
In Cable mode, the BT01 microphone is being charged when the
channel is free.
4.4-Power Off
Press and hold the top [POW] button on microphone to turn off the
microphone.
4.5-Adjust The Volume
In standby state, press the top [POW] button to switch the [CH-]/[CH+]
button for volume adjust use.
When screen shows "UpDn Key: Vol Set " , press [CH-] to reduce
the volume, press [CH+] to increase the volume.
The [VOL] or [CH] icon shows the current setting.
BT01 microphone is able to access the radio menu and do
communications now.

5
»If the volume is adjusted to the maximum and you still consider
it is not loud enough.
»In BT MODE, you can enter into Menu ->Bluetooth->RfBT SPK
Gain to adjust the Bluetooth gain level and increase the volume.
»The RfBT SPK Gain will return to default level 3 after reboot
the radio, as the level 3 has best effect.
4.7-Select a Channel
Press the assigned [VFO/MR] key to switch the radio into channel
mode, and then press the top [POW] button to switch the [CH-]/[CH+]
button for channel adjust use.
In BT mode, if you press the [CH-]/[CH+] button rapidly to switch
the channel, the BT01 display reacts more slowly than the button
press. It is recommended to input the channel number by keypad on
microphone to access the channel rapidly, for example, input 0,0,9,9
a total of 4digits will switch to channel 99. In case the input channel
number is not in the current zone, the microphone will emit “du”
beep and stay at the current channel.
4.6-Set Up VFO Frequency
In Menu->Setting->Radio Set->Key Func, assign a key function to
[VFO/MR].
Press the assigned [VFO/MR] key to switch the radio into VFO
frequency mode, and then press the or key to change the
frequency in MHz steps. The frequency steps shall be set in CPS
Optional Setting Other Frequency step or in radio menu.
And it allows input the frequency by keypad on microphone to
change the frequency rapidly, for example, input 4,5,0,1,2,5,0,0 or
4,5,0,1,2,5,# to obtain 450.125MHz.
»Normally you shall input 8 digits to change the frequency, in
case the end of the frequency is 0, you can press # key to
confirm the valid frequency instead of input several 0.

6
And in BT mode, when BT microphone is receiving signal, the
channel switch speed is slow, it is difficult to improve due to the
limitation of bluetooth communication.
4.8-Select a Zone
Press the assigned [VFO/MR] key to switch the radio into channel
mode first.
Operation 1: Press the or key to change the zone.
Operation 2: Go to Menu Zone, select a zone from the zone list.
Operation 3: In Menu Setting Radio Set Key Func, assign a
key function to [Zone Select]. Press the assigned [Zone Select] key,
and input the zone number and confirm.
4.9-Make a Call
Press and hold the [PTT] button to start a call at the current channel,
the left red indicator lights on and the radio is transmitting. Release
the [PTT] button to stop the transmitting.
4.10-Receive a Call
When the radio receives a call, the right green indicator lights on and
the radio is receiving.
4.11-Noise Reduction function
Enable the noise reduction function can reduce background noise
and ambient noise effectively, and make calls between users clearer.
Noise reduction works basing on the noise intensity, when the noise
is strong, noise reduction reduces more noise and the audio has
more distortion.
When the noise is slight, noise reduction reduces less noise and the
audio has less distortion, it may not noticeable for noise reduce.
And set the noise reduce level higher, the noise will be reduced
more and the audio has more distortion.

7
4.12-Menu Operation
The menu operation on BT microphone is mapped from AT-
D578UV radio, the functions are fully same as AT-D578UV radio.
Bluetooth menu function as below.
BT Menu Sub menu Description
BT
Pairing -- Disconnects to the radio.
BT
Names -- The BT name of BT01 microphone.
Paired
Names -- The BT name of BT device connected to the AT- D578UV radio.
BT Hold
Time
OFF
The BT01 microphone disconnects to the radio at
once when signal drops. It takes time to rebuild the
connection when new signal come in.
1-30S
The BT01 microphone stays connecting to the radio
within the set time after signal drops, after the set
time dispired, the BT device will disconnect to the
radio.It takes time to rebuild the connection when
new signal come in.
innite
The BT01 microphone stays connecting to the radio
after singal drops.It will pick up the signal at once
when new signal come in.
BT RX
Delay 30ms-5.5s
The radio will ignore the RX signal if the duration of
the signal does not exceed the set time. It helps to
prevent the interfere signal being heard.
You can set suitable noise reduce level to get acceptable noise and
audio effect.
Go to Menu Settings Radio Set Voice Func Noise
Reduce(RX), set the noise reduce level for receiving use,
recommend setting is level 3. Noise reduce for analog RX only.
Go to Menu Settings Radio Set Voice Func Noise
Reduce(TX), set the noise reduce level for transmit use,
recommend setting is level 3. Noise reduce for both analog TX and
digital TX.

8
BT + int
spk
Off The audio comes out from the speaker on BT01
microphone.
On The audio comes out from the speaker on AT-
D578UV radio.
RfBT Mic
Gain Level 1-5 Adjust the transmit audio level on AT-D578UV radio.
RfBT
SPK
Gain
Level 1-5 Adjust the receive audio level on AT-D578UV radio.
H-BT Mic
Gain Level 1-5 Adjust the transmit audio level on BT01 microphone.
BT Pin
Code -- Allows entry of BT Pin Code During Pairing. Majorly for the use of pairing to Car Audio System.
BT PTT
Pair
PTT Pair Pair the small BP-02 BT PTT button.
PTT Hold
ON:Click on BP-02 PTT button, the radio starts
transmitting, click on the BP-02 PTT button again to
end transmitting.
OFF: Hold pressing BP-02 PTT button to transmit,
release the button to end transmitting.
PTT Name The BT name of BP-02 PTT button.
PTT Sleep
Innity: The BP-02 PTT button will not go into
dormant mode.
1-4min : The BP-02 PTT button will go into dormant
mode in the set time.It requires to hold pressing the
BP-02 PTT button to activate it when it is in dormant
mode.
PTT
BatVolt Shows the BP-02 PTT button battery level.
4.13-Programmed Key
It is possible to set different functions for [P1], [P2], [P3] side keys
on microphone.
Method 1: In radio Menu Settings Radio Set Key Func
Method 2: In PC software Public Optional Setting BT
Bluetooth handset.

9
OFF No Function
Volt Check the current battery capacity voltage
Tx Power Switch the power between super high, high, middle
and low power.
TalkAround Switch between Talk Around and Repeater mode
Reverse Turn on/off the frequency reverse function.
Digi Encrypt Choose the digital encryption group for digital
channel
Call
In Analog mode, send the DTMF/5TONE/2TONE
encode. This function is only valid for analog
channel.
VFO / MR Switch between VFO mode and memory channel
mode.
Scan Scan on/off
AM air/FM Turn on/off AM air band receive or FM radio receive
Alarm Long press the key to start alarm, short press again
to exit the alarm.
Record Switch Enable/disable the recording function
Record Start/stop recording. When stop recording, the radio
will remind repeat or send the record.
Messages In digital mode, press to enter into SMS messages
Dial Start the manually dial
GPS Info Check the GPS position information
Monitor Monitor the weak signal or the signal with
unmatched ID.
Each [P1], [P2], [P3] key allows to assign different functions for
short press, long1 press and long2 press.
Short : Function takes effect after click on the button.
Long1: Function takes effect after "du" beep, it needs approx 1.5s
for the press.
Long2: Hold pressing the button until function takes effect, it needs
approx 3s for the press.

10
Main CH Switch Choose channel A or channel B as the main channel
Hot Key 1~6 Selects Hot Keys 1-6 Note: Hot key setup details on
next page
Work Alone Turn on/off the work alone function.
Nuisance
Delete
During scanning, press the key to skip the unwanted
channel
Digi Monitor In DMR mode, press the key to turn on/off digital
monitor
Sub CH On/Off Turn on/ off the sub channel
Priority Zone Switch to Priority Zone
Program Scan
Press the key to start the scan in VFO channel scan
start and end frequency must be programmed in
CPS.
Enhanced
Sound
In digital channel, switch the microphone tone to
normal or enhanced mode.
LastCall Reply In digital channel, press the key to access the last
call and press PTT to call back.
Switch ChType Switch the channel type(Analog, Digital, Ana+Dgi,
Dgi+Ana)
Ranging
When the radio receives a call and the suspension
time is on, press the key programmed as "Ranging"
to obtain the caller's position and distance. (Both
party need GPS positioned, or will receive only GPS
information)
Roaming
In standby, press the key programmed as "Roaming"
to search and lock on the repeater with strongest
signal. (Note: After lock on a repeater, the radio
will return to last frequency only after channel or
frequency is changed. The repeater frequency list
must pre- programmed in CPS.)
CH Ranging
In standby, if the call contact type for a channel
is "Single call" , press the key programmed as "
Channel Ranging" to turn on this function. The radio
will automatically start ranging function when turn to
this channel.

11
Max VOL Set
In standby, press the key programmed as" Max
Volume", will enable users to set the maximum RX
volume.
Slot Set Choose Slot for current channel, this function is only
valid in repeater mode.
Aprs Type Choose analog or digital Aprs Type for current
channel.
Zone Select
In standby, press the programmed "Zone Select"
key, it will allow you input the zone number and then
press conrm key will switch to the zone.
Roaming Set Enter into Roaming menu quickly
APRS Set Enter into APRS menu quickly
Zone Up Switch the zone upwardly
Zone Dn Switch the zone downwardly
Speaker Mode Set the voice come out from speaker on microphone
or radio.
Ch.Name Switch between channel name display and
frequency display for the current channel
GPS On/Off Enable / disable the GPS.
CDT Scan
Enable / disable the CTCSS/DCS scanning for
the analog channel.When the radio nds matched
CTCSS/DCS for current channel, it will open the
speaker and start receiving.
Only the analog channels with CTCSS/DCS
signalling is able to start the CDT scanning.
TBST Send Send the TBST Tone
Aprs Send Manually transmit the APRS at the current channel.
Ana APRS Info Fast access to the anglog APRS info menu
GPS Roaming Enable/disable the GPS roaming function
NoiseReduc(R) Set the noise reduce level for receiving audio
NoiseReduc(T) Set the noise reduce level for transmitting audio

12
5.Technical Specifications
GENERAL
BT version BT version V5.0 +EDR
Protocol HFP; HSP; A2DP; AVRCP; SPP
Transmit Distance 10 Meters
Maximum Transmission
Power Class2, 4dbm
Sensitivity -80dBm
Audio performance SBC Decoding
Speaker 1W/8R
LED Green/Red
LCD screen 2.2inch
Charge 5V Type C USB
Battery capacity/Votage 1800mAh 3.7V
Interface 3.5mm
Dimension (H*W*D) 109x62x28mm
Weight 147g
Working Temperature -20°C ~ 55°C

13
EU Declaration of Conformity
In accordance with EU Directives and Regulations
Qixiang Electron Science& Technology Co., Ltd
ADD: Qixiang Building, Tangxi Industrial Zone, Luojiang, Quanzhou, Fujian, 362011 China
as the manufacturer, hereby declares under our sole responsibility that
product(s): Bluetooth Microphone
Model name: BT01, BT02, BT03, BT04, BT05, BT06
is in conformity with the essential requirements of the Radio Equipment Directive 2014/53/EU:
Radio ETSI EN 300 328 V2.2.2 (2019-07)
Article 3.2
EMC ETSI EN 301 489-1 V2.2.3 (2019-11)
Article 3.1(b) DRAFT ETSI EN 301 489-17 V3.2.5 (2022-08)
Safety EN IEC 62368-1:2020+A11:2020
Article 3.1(a)
Health EN 50663:2017
Article 3.1(a) EN 62479:2010
The notified body Bay Area Compliance Labs Corp.(BACL) (EU Identification Number: 1313)
performed a conformity assessment according to Annex III, Module B.
Signed on behalf of Qixiang Electron Science& Technology Co., Ltd
(Signature of authorized person)
Name: Ken Xu
Title: General Manager
Date: 2022-11-15