Anzzi BA-LMDFX018AL User manual

ITEM: BA-LMDFX018AL
FRONT & BACK LIGHTING LED MIRROR
INSTALLATION & OPERATION MANUAL
V1.0
01/26/2023

BA-LMDFX018AL Dia 24"
1
PRODUCT SIZE CHART
MOUNTING DIMENSIONS
1.18" [30mm]
3.74" [95mm]
12.8" [325mm]
24" [610 mm]

Please read carefully and save these instructio
For the style of LED Mirror shown below
ns.
Don’t discard any of the packaging until you are sure that you have all of the parts and the fittings.
Make sure power to the junction box or outlet is off before commencing installation.
Always unplug the mirror from the outlet or turn off the switch before cleaning or
servicing to reduce the risk of electric shock.
DANGER
.
.
.
.
DO NOT lay mirror on tiled or concrete surface
prior to installation.
Mirror must be on protected surface to prevent
chipping of the corners.
We highly recommend you have your mirror
professionally installed if you are not familiar
with basic plumbing and electricity. DO NOT
attempt to install, repair or disassemble the
LED mirror without first disconnecting the
electricity.
When drilling pilot holes, be careful to avoid any
wiring or pipe work that may be concealed behind
the wall.
The mirror must be connected to a GFCI outlet.
Risk of Electric Shock, Fire, and Injury.
Keep the cord away from heated surfaces.
Risk of Electric Shock – Connect this mirror to
a properly grounded outlet only.
See Grounding Instructions.
WARNING
.
.
.
.
.
.
.
.
This product must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or
lead on the product.
Never operate this mirror if it has a damaged cord or
plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return
the mirror to a service center for examination and
repair.
Do not operate where aerosol (spray) products are
being used or where oxygen is being administered.
To disconnect, turn off mirror and unplug power cord
from outlet.
Review the assembly instructions to confirm that the
correct components and accessories are being used
with the mirror.
Close supervision is necessary when this mirror is
used by or near children, invalids, or disabled
persons.
Do not use outdoors.
.
.
.
.
.
.
.
2

.
INSTALLATION INSTRUCTIONS
TOOLS REQUIRED
ATTENTION
3
Handle the glass with caution! Improperly handling
the glass can cause it to break.
You will need at least two people to install this unit
properly.
Inspect all parts for damage; if there is damage to
the unit prior to installation, please contact
customer service at the number provided in this
guide.
Make sure that the electricity is turned off at the
power source before proceeding with the
installation or cleaning.
.
.
.
Always unplug the power supply cord from the outlet
before moving the product, testing the product,
or repairing the product.
The defogger operates only when the LED light
is turned on.
Use this mirror only for its intended use as described
in these instructions. Do not use attachments that
are not recommended by the manufacturer.
Statement: ANZZI does not assume any
responsibility for the losses caused by the
improper installation and behavior listed above
or other improper operations.
.
.
.
.
5/161/8
3

SCREW
(x2)
WALL PLUG
(x2)
Twist-cap Connector
(x3)
X1
Position Template x1
Make sure the holes of template matches the hanging
holes of the mirror.
Measure the distance "h" from the Position Template
to the top of the product.
According to the height "H" of the product, place the
Position Template horizontally on the wall and mark
the installation holes with pencil.
For exact distance, reference the Mounting
Dimensions figure on page 1.
deck surface
INSTALLATION INSTRUCTIONS
4
21
43
h
h
H
distance

A
B
C
1/4”- 5/16”
5
INSTALLATION INSTRUCTIONS
Twist-cap Connector
65
7
If drilling into wood, drill a 1/8”hole at each marked
location (figure A) and install screws into holes. If
drilling into concrete, drill a 5/16”hole at each marked
location (figure A, B, C), insert wall plugs, and install
screws into the wall plugs. Leave a gap of 1/4”-5/16”
between the screw head and the wall.
The LED mirror is provided with a power supply cord.
For the plug-in connection, place the mirror against the
wall and slide down as shown. Then plug the power
supply cord into the outlet to finish the installation. For
the wire connection, please cut the power supply cord
near the plug and connect the wire by following step 7.
Then secure mirror by following step 6.
Cable
LED Mirror
WHITE or LABELED - N
GREEN - E
BLACK or LABELED - L
NEUTRAL
EARTH(GREEN/YELLOW
SLEEVED COPPER)
SWITCHED LIVE
INCOMING SUPPLY
L
N
MIRROR WIRING
WIRING DETAILS
Before starting the wire connection, please make
sure the electricity supply has been turned off.
For the wire connection, please cut the power supply
cord and strip a section of sheath and insulation from
the cable. Connect the neutral (N) and live (L) wires to
the mirror's power supply wires, using the Twist-cap
Connectors. Connect the mirror’s green wire to the
grounding wire in the junction box with a Twist-cap
Connector. Carefully push the wires into the junction
box.
A
B
Live wire
Earth wire
white wire
black
wire
green
wire
Neutral
wire

6
OPERATION
MAINTENANCE
Press this key to turn the LED light on or off. The defogger operates when the LED light is
Turn on the power supply before you use the mirror.
turned on.
Press and hold to change the color temperature from 2700-6500k. It will change gradually
(2700-6500k).
Press and hold to change the brightness from 10%-100%. It will change gradually (10%-100%).
Wipe clean with a soft damp cloth. Apply glass cleaner to cloth and do not apply directly to mirror.
An occasional wiping down with a mild soap diluted in water is all that is needed to keep the mirror
and aluminum parts looking new. Never use abrasive cleaners as these could damage the finish or
exposed LED strips. Never use scouring powder pads, abrasive material, strong bleach or sharp
instruments on metal components or glass. Test products on a smalI inconspicuous surface prior
to use.