AOC FOVI F19S User manual

18.5" LCD Monitor AOCF19s
1
Service
Service
Service
Horizontal Frequency
30- 80kHz
Table of Contents
Description Page Description Page
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
Table of Contents…………………..…………………..…...1
Revision List.…...................................................……......2
Important Safety Notice.….….............................……......3
1.Monitor Specification..............................………............4
2.LCD Monitor Description……….…………………….......5
3.Operation Instruction.…………...................……...........7
3.1.General Instructions....................................…...........7
3.2.Control Buttons and Connections...............................7
3.3.OSD Settings….........................................................8
4.Input/Output Specification...............……………….......11
4.1.Input Signal Connector...............………..................11
4.2.Factory Preset Display Modes……..........................11
4.3.Panel Specification…………..………………………..12
5.Block Diagram….........................................................16
5.1.Main Board…..….............................................16
5.2.Power Board…………..…………………………......17
6.Schematic…………..….........................................18
6.1.Main Board..…….…...........................................18
6.2.Power Board..……….........................................22
7.PCB Layout..………..............................................24
7.1.Main Board………..…........................................24
7.2.Power Board….…..............................................26
7.3.Key Board………..…..........................................28
8.Maintainability………............................................29
8.1.Equipments and Tools Requirement…...............29
8.2.Trouble Shooting…..………...............................30
9. FOS Testing………………………………………34
10.Firmware and DDC Instruction……………….….38
11.White-Balance,Luminance Adjustment…............49
12.Monitor Exploded View……................................51
13.BOM List…………..……………………….............52
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING

2
Revision List
Version Release Date Revision History TPV Model Name
A00 Nov.-10-2010 Initial release
T8AAR5NKX8A1NNE
T8AAR5NEX8A1NNE
A01 Jan.-12-2011
Add new models
T8AAR5NPX8A1NNE
T8AAR5NQX8A1NNE
Add second Panel
(CPT CLAA185WA03)
T8ACR5NCX8ACNNE
T8ACR5NEX8A1NNE
T8ACR5NKX8A1NNE
A02 Feb.-22-2011 Add new models
T8ACR5NPX8A1NNE
T8ACR5NQX8A1NNE

3
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service
procedures recommended by AOC and described in this service manual are effective methods of performing service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock,
fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER-Invisible laser radiation when open AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)

4
1. Monitor Specifications
LCD Panel
Model number F19s
Driving system TFT Color LCD
Viewable Image Size 470mm diagonal
Pixel pitch 0.3mm(H) x 0.3mm(V)
Video R, G, B Analog lnterface
Separate Sync. H/V TTL
Display Color 16.7M Colors
Dot Clock 85.5 MHz
Resolution
Horizontal scan range 30 kHz - 80 kHz
Horizontal scan Size(Maximum) 409.8mm
Vertical scan range 55 Hz - 75 Hz
Vertical scan Size(Maximum) 230.4mm
Optimal preset resolution 1360 x 768 (60 Hz) or 1366 x 768 (60 Hz)
Highest preset resolution 1366 x 768 (60 Hz)
Plug & Play VESA DDC2B/CI
Input Connector D-Sub 15pin
Input Video Signal Analog: 0.7Vp-p(standard), 75 OHM
Power Source 100-240VAC, 50/60Hz
Power Consumption Active < 25 W
Standby < 1 W
Physical
Characteristics
Connector Type 15-pin Mini D-Sub
Signal Cable Type Detachable
Dimensions & Weight:
Height (with base) 334.3 mm
Width 445.8 mm
Depth 130.1mm
Weight (monitor only) 3.7 kg
Weight (with packaging) 4.8 kg
Environmental
Temperature:
Operating 0° to 40°
Non-Operating -20°to 60°
Humidity:
Operating 10% to 85% (non-condensing)
Non-Operating 5% to 80% (non-condensing)
Altitude:
Operating 0~ 3000m (0~ 10000 ft )
Non-Operating 0~ 5000m (0~ 15000 ft )

5
2. LCD Monitor Description
The LCD MONITOR will contain a main board, a power board, and a key board which house the flat panel control
logic, brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.
HOST Computer
AC-IN
100V-240V
Power board
(Include: adapter, inverter)
Flat Panel and
CCFL backlight
Main Board
RS232 Connector
For white balance
adjustment in factory
mode
CCFL Driver
Video signal DDC
Key board
Monitor Block Diagram

6
View and Dimension

7
3. Operating Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the
monitor.
By changing these settings, the picture can be adjusted to your personal preferences.
- The power cord should be connected.
- Connect the video cable from the monitor to the video card.
- Press the power button to turn on the monitor, the power indicator will light up.
3.2 Control Buttons and Connections
1 Eco mode(DCR) / Up
2 Auto / Down
3 Contrast / Left
4 4:3 or wide / Right
5 Menu / Power
1. Power
2. Analog
Turn off your computer before performing the procedure below.
1. Connect the power cable to the AC port on the back of the monitor.
2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the
computer's D-Sub port.
3. Turn on your monitor and computer.
If your monitor displays an image, installation is complete. If it does not display an image, see Troubleshooting.

8
3.3 OSD Settings
•Press the Menu (Power) button to activate the OSD window. Press left, right, up, down button to navigate
through the functions. Once the desired function is highlighted, press the Menu (Power) button to activate
sub-menu .
•In sub-menu, Press up, down button to navigate through the functions. Once the desired function is
highlighted, press , button to button to change the setting. Press Menu (Power) button to return to
superior menu.
•If you want to adjust any other function, repeat steps 1-2.
•To exit OSD windows, select “exit” icon on main OSD, then press the Menu (Power) button .
•OSD Lock Function: To lock the OSD, press and hold the Left button while the monitor is off and then press
power button to turn the monitor on. To un-lock the OSD - press and hold the Left button while the monitor is
off and then press power button to turn the monitor on.
•Eco Mode and DCR hot key : Press the Eco key continuously to select the Eco mode of brightness and DCR
on when there is no OSD ( Eco mode hot key may not be available in all models).
•Contrast adjustment hot key : When there is no OSD , press Contrast ( ) to active Contrast adjustment bar,
press or to adjust Contrast.
•4:3 or wide image ratio hot key: When there is no OSD, press continuously to change 4:3 or wide image
ratio. (If the product screen size is 4:3 or input signal resolution is wide format, the hot key is disalbe to
adjust.)
•Auto configure hot key: When the OSD is closed, press Auto button will be auto configure hot key function .
•Press the Power button continuously about 2 second to turn off the monitor.

9
Function Control Illustration
Luminance Adjust Range Description
Brightness 0-100 Backlight Adjustment
Contrast 0-100 Contrast from Digital-register.
Eco mode
Standard
Standard Mode
Text
Text Mode
Internet
Internet Mode
Game
Game Mode
Movie
Movie Mode
Sports
Sports Mode
Gamma
Gamma1 Adjust to Gamma1
Gamma2 Adjust to Gamma 2
Gamma3 Adjust to Gamma 3
DCR
Off
Disable dynamic contrast ratio
On
Enable dynamic contrast ratio
Image Setup
Clock 0-100 Adjust picture Clock to reduce
Vertical-Line noise.
Phase 0-100 Adjust Picture Phase to reduce
Horizontal-Line noise
H.Position 0-100 Adjust the horizontal position of
the picture.
V.Position 0-100 Adjust the verticalposition of the
picture.
Color Temp.
Warm 6500K
Recall Warm Color Temperature
from EEPROM.
Normal 7300K
Recall Normal Color
Temperature from EEPROM.
Cool 9300K
Recall Cool Color Temperature
from EEPROM.
sRGB
Recall SRGB Color Temperature
from EEPROM.

10
User
Red Red Gain from Digital-register
Green Green Gain Digital-register.
Blue Blue Gain from Digital-register
Color Boost
Full Enhance on or off Disable or Enable Full Enhance
Mode
Nature Skin on or off Disable or Enable Nature Skin
Mode
Green Field on or off Disable or Enable Green Field
Mode
Sky-blue on or off Disable or Enable Sky-blue Mode
AutoDetect on or off Disable or Enable AutoDetect
Mode
Demo on or off Disable or Enable Demo
Picture Boost
Frame Size 14-100 Adjust Frame Size
Brightness 0-100 Adjust Frame Brightness
Contrast 0-100 Adjust Frame Contrast
H. position 0-100 Adjust Frame horizontal Position
V.position 0-100 Adjust Frame vertical Position
Bright Frame on or off Disable or Enable Bright Frame
OSD Setup
H.Position 0-100 Adjust the horizontal position of
OSD
V.Position 0-100 Adjust the vertical position of
OSD
Timeout 5-120 Adjust the OSD Timeout
Transparence 0-100 Adjust the transparence of OSD
Language Select the OSD language
Extra
Input Select Analog Select Analog Sigal Source as
Input
Auto Config yes or no
A
uto adjust the picture to default
Image Ratio wide or 4:3 Select wide or 4:3 format for
display
DDC-CI yes or no Turn ON/OFF DDC-CI Support
Information
Show the information of the main
image and sub-image source
Reset
Reset yes or no Reset the menu to default
Exit
Exit Exit the main OSD
LED Indicators
Status LED Color
Full Power Mode Green or Blue
Active-off Mode Orange or red

11
4. Input/Output Specification
4.1 Input Signal Connector
Pin Number 15-Pin Side of the Signal Cable
1 Video-Red
2 Video-Green
3 Video-Blue
4 N.C.
5 Detect Cable
6 GND-R
7 GND-G
8 GND-B
9 +5V
10 Ground
11 N.C.
12 DDC-Serial data
13 H-sync
14 V-sync
15 DDC-Serial clock
4.2 Factory Preset Display Modes
STAND RESOLUTION
HORIZONTAL
FREQUENCY(kHZ)
VERTICAL
FREQUENCY(Hz)
VGA 640 x 480 @60Hz 31.469 59.940
VGA 640 x 480 @72Hz 37.861 72.809
VGA 640 x 480 @75Hz 37.500 75.000
Dos-mode 720 x 400 @70Hz 31.469 70.087
SVGA 800 x 600 @56Hz 35.156 56.250
SVGA 800 x 600 @60Hz 37.879 60.317
SVGA 800 x 600 @72Hz 48.077 72.188
SVGA 800 x 600 @75Hz 46.875 75.000
Mac-mode 832 x 624 @75Hz 49.725 74.500
XGA 1024 x 768 @60Hz 48.363 60.004
XGA 1024 x 768 @70Hz 56.476 70.069
XGA 1024 x 768 @72Hz 57.500 72.074
XGA 1024 x 768 @75Hz 60.023 75.029
XGA 1024 x 768 @75Hz 47.712 74.927
WSXGA 1366 x 768 @60Hz 47.765 59.85

12
4.3 Panel Specification
4.3.1 General Features
AUO M185XW01
CPT CLAA185WA03
CLAA185WA03_V2 is 18.51” color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module composed of LCD
panel, driver ICs, control circuit and backlight. By applying 6bit+Hi-FRC digital data,1366*768, 16.7M-color images
are displayed on the 18.51” diagonal screen. Input power voltage is 5.0V for LCD driving. Inverter for backlight is not
included in this module. General specification are summarized in the following table:
4.3.2 GENERAL SPECIFICATIONS
AUO M185XW01
(Ta= 25±2℃)
CPT CLAA185WA03

13
4.3.3 Electrical Characteristics
1. TFT LCD Module
AUO M185XW01
(Ta= 25±2℃)
CPT CLAA185WA03
Ta= 25±2℃，VCC=5.0V, Fh=47.28KHz, Fv=60Hz, Fclk=67.1MHz.

14
2 .BackLight Unit
AUO M185XW01
(Ta= 25±2℃)
CPT CLAA185WA03

15
4.3.4 Optical Characteristics
AUO M185XW01
(Ta= 25±2℃)
CPT CLAA185WA03
Ta=25℃，VCC=5.0V

16
5. Block Diagram
5.1 Main Board
715G3244 2 2
PB[0..9]
T99SRD*TVNN F
A1981Wx A
37Thursday , May 06, 2010
G3244-2-2 <
称爹 >
01.Top
G3244-2-2-X-8-100426
OEM MOD EL Size
Rev
Date Sheet of
TPV MOD EL
PCB NAME
称爹
T P V ( Top Victory Electronics Co . , Ltd. )
Key Component
絬 隔 瓜 絪 腹
VCC3.3
VCC3.3
TSUM1PFR SCHEMATIC
04.Output
CMVCC
PB[0..9]
PA[0..1]
PPWR_ON#
PA[4..9]
CMVCC
CMVCC1
CMVCC1
VCC1.8
XGA/SXGA
03.Scalar
DSUB_R+
DSUB_G+
DSUB_SOG
DSUB_B+
DSUB_R-
DSUB_G-
DSUB_B-
DSUB_H
DSUB_V
Adj_BACKLIGHT
VCC1.8
VCC3.3
PA[0..1]
PB[0..9]
DDC1_SDA
DDC1_SCL
DET_CABLE
on_BACKLIGHT
PPWR_ON#
PANEL_ID#
Volume#
Mute
PA[4..9]
CMVCC1
VCTRL
EDID_CTRL
05.Power
on_BACKLIGHT
Adj_BACKLIGHT
VCC1.8
CMVCC
VCC3.3
Mute
Volume#
PANEL_ID#
CMVCC1
VCTRL
PA[4..9]
CMVCC1
CMVCC
PA[0..1]
VCC1.8
02.Input
DSUB_R+
DSUB_G+
DSUB_B+
DSUB_V
DSUB_R-
DSUB_G-
DSUB_B-
DET_CABLE
DSUB_H
DSUB_SOG
DDC1_SDA
DDC1_SCL
CMVCC1
EDID_CTRL
LVDS OUTPUT

17
5.2 Power Board
715G2852 2 11
ON/OFF
DIM
Feedback
Circui
t
Transformer
(T801)
MOSFET
(Q802)
B/L
Output
Circui
t
PWM Control
TL494IDR
(IC801)
12V
EMI filter
Start Resistor
(R904,R932)
PWM Control
LD7575A
(IC901)
Transformer
(T901)
AC input 12V
Bridge
Rectifier
and Filter
Feedback
Circuit
Rectifier
diodes
Photo coupler
(IC902)
Power Switch
(Q901)
Regulator
(IC903)
5V

18
6. Schematic
6.1 Main Board
715G3244 2 2
VGA_G+
ESD_5V
C109
0.047uF
DSUB_5V
CMVCC1 5,6,7
VGA_R+
VGA_PLUG
R473
4K7 1/16W 5%
VGA_PLUG
VGA_G+
DDC1_SCL
R111
100R 1/16W 5%
VGA_G-
R116
75R 1/16W 5%
V_Sy nc
R476 47R 1/16W 5%
U103
AZC199-04S
1
2
3 4
5
6
I/O1
GND
I/O2 I/O3
VDD
I/O4
CMVCC1
DSUB_SDA
T99SRD*TVNN F
A1981Wx B
47Thursday , May 06, 2010
G3244-2-2 <
称爹 >
02.Input
G3244-2-2-X-8-100426
OEM MOD EL Size
Rev
Date Sheet of
TPV MOD EL
PCB NAME
称爹
T P V ( Top Victory Electronics Co . , Ltd. )
Key Component
絬 隔 瓜 絪 腹
DSUB_V 5
R105
2K2 1/16W 5%
DSUB_G- 5
H_Sy nc
VGA_G+ DSUB_G+ 5
DSUB_SDA
C113
0.047uF
CMVCC1
C114
NC
ESD_5V
R114
100R 1/16W 5%
R118
10K 1/16W 5%
EDID_CTRL 5
DSUB_SDA
FB101
BEAD
1 2
DSUB_R- 5
CN101
DB15
1
6
2
7
3
8
4
9
5
11
12
13
14
15
10
17 16
R101 0R05 1/10W 5%
C108
5pF/50V
R475 47R 1/16W 5%
DDC1_SCL5
R112
75R 1/16W 5%
C115
NC
DSUB_B- 5
R103 100R 1/16W 5%
FB103
BEAD
1 2
U102
AZC199-04S
1
2
3 4
5
6
I/O1
GND
I/O2 I/O3
VDD
I/O4
DSUB_SOG 5
DDC1_SDA5
DSUB_B+ 5
ZD103
RLZ5.6B
R107
75R 1/16W 5%
DSUB_5V
Q407
LMBT3904LT1G
R104
100R 1/16W 5%
VGA_B+
VGA_B-
DSUB_SCL
R474
4K7 1/16W 5%
VGA_R+
C110
0.047uF
C106
1000pF
DGND
VGA_PLUG
DSUB_SCL
R122
NC
GND POWER
VGA_R-
C104
5pF/50V
C105
0.047uF
D403
BAV70
3
1 2
DET_CABLE 5
R472
4K7 1/16W 5%
候綼 U102
R102 100R 1/16W 5%
R109
390 OHM 1/16W
VGA_G-
DSUB_5V
VGA_B+ C107
0.047uF
DSUB_H 5
DSUB_SCL
ESD_5V
V_Sy nc
VGA_R+
DDC1_SDA
C103
22pF
C111
5pF/50V
VGA_B-
C101
0.047uF
R115
100R 1/16W 5%
VGA_B+
C434
0.22uF16V
R106
2K2 1/16W 5%
U405
AT24C02BN-SH-T
1
2
3
45
6
7
8A0
A1
A2
GNDSDA
SCL
WP
VCC
R108
100R 1/16W 5%
候綼 U103
FB102
BEAD
1 2
C102
22pF
DSUB_R+ 5
H_Sy nc
VGA_R-
R117
100R 1/16W 5%

19
R411 100R 1/16W 5% KEY2
LED_GRN/BLUE
PB9
DSUB_V4
DSUB_B+4
PA[0..1] 6
VCC3.3
SST
C417
0.1uF /16V
U402
PANEL_ID# and POWER_KEY#
could be optional.
LED_O
MSC L
POWER_KEY #
R463 NC
C412
22pF
R412 100R 1/16W 5%
C433
NC
Without NVRAM
VCC3.3
PB6
DSUB_G-4
NC
PA4
R451 NC
U402
NC
LED_OR ANGE/TOUCH VCC
R487
4.7K1/16W
PA9
DSUB_H4
NC
AVDD
R428
3.9K OH M 1/16W
CN406
NC/CONN
1
2
3
4
5
6
7
8
CN402
NC/CONN
1
2
3
4
5
6
10K 1/16W 5%
T99SRD* TVNN F
A1981Wx C
57Thursday , May 06, 2010
G3244-2-2 <
称爹 >
03.Sc alar
G3244-2-2-X-8-100426
OE M MOD EL Si ze
Rev
Date Sheet of
TPV MO D EL
PCB N AME
称爹
T P V ( Top Victory Electronics Co . , Ltd. )
Key Component
絬 隔 瓜 絪 腹
CMVCC1
When NVRAM is used,
POWER_KEY# and PANEL_ID#
will not be used at same
time.
LED_GRN/BLUE
C418
NC
ZD 402
NC /MLVS0603M04
1 2
DSUB_SOG4
LED_O
PB1
R403 390 OHM 1/16W
100R 1/16W 5%
Eon
MSDA
RTD2270S-GR
U401
13
10
11
8
12
9
7
16
17
4
15
14
21
23
22
24
27
56
1
2
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
34
33
5
6
32
31
52
30
18
19
62
20
28
55
58
59
60
61
63
64
25
26
54
51 53
29
57
3
RIN0P
GIN 0P
SOGIN 0
BIN0P
RIN0M
GIN 0M
BIN0M
HSYNC0
VSY NC0
REXT
REFP
REFM
SDO
SCK
SCZ
SDI
PWM2/GPIO_P24
PWM1/GPIO_P25
XI N
XO U T
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
LVA3M
LVA3P
GND
AVDD_ADC
MOD E [ 1 ]
MOD E [ 0 ]
VCTRL
VDDC
DDCA_SDA/ RS232_TX
DDCA_SCL/rs232_RX
PWM0/GPIO_P26
GPIO_P15/ PWM0
GPIO_P27/ PWM1
GPIO_P12
GPIO_P00/ SAR1
GPIO_P01/ SAR2
GPIO_P06
GPIO_P07
GPIO_P13
GPIO_P14
GPIO_P11/I2C_MDA
GPIO_P10/ I2C_MCL
RST
VDDP
VDDC
GND
RSTN
GND
CN409
NC/CONN
1
2
3
4
5
6
7
For user data, WB, EDID,
HDCP are saved in
Flash.
NC
LED_ORANGE/TOUCH VCC
C407
0.1uF /16V
CN407
NC/CONN
1
2
3
4
5
6
7
R414 10K 1/16W 5%
CN408
CONN
1
2
3
4
5
6
DSUB_B-4
R425, C418 depend on
case.
EE_WP
PA1
C414
MLVS0402M04
12
U403
NC/M24C04-WMN6TP
1
2
3
45
6
7
8NC
E1
E2
VSSSDA
SCL
WC
VCC
FB404
NC
WP
R453
SST
R427
3.9K OH M 1/16W
R401
100R 1/16W 5%
R419 N C/100OH M1/16W
VCC3.3
R424
R464 NC
PANEL_I D# 7
R454
Eon
VCC3.3
KEY 1
FB405
NC
Befor AOC ID2007 OSD
For NVRAM
AVDD
+
C410
NC/10uF/ 50V
PA6
PA0
X401
14.31818MHz
1 2
Volume# 7
NC
VCC3.3
C403
0.1uF/16V
R420 100R 1/16W 5%
C406
0.1uF/16V
PA7
NC
When use touch
Key,GPIO_P07 as
to control touch
key VCC
NC
CMVCC1
100R 1/16W 5%
LED_G/ B
R402
0R05 1/16W
R417
NC/10K 1/16W 5%
R404
10K 1/16W 5%
VCC3.3
R485 4K7 1/16W 5%
M24C04-WMN6TP
NC or 100R 1/16W 5%
R455
R421
10K 1/16W 5%
PB[0..9]
R478 NC
R481
0R05 1/16W
10K 1/16W 5%
PB4
C401
0.1uF /16V
020A
LED_G/B
C413
MLVS0402M 04
12
C411
22pF
PB[0..9] 6
0.22uF16V
PA8
C415
MLVS0402M04
12
R461 0R05 1/ 16W
R451
Q402
LMBT3906LT1G
PA5
C404
1UF 10V
010A
NC
R462 0R05 1/ 16W
ZD 401
NC /RLZ 5.6B
KEY 2
TOUCH POWER
LED_ORANGE/TOUCH VCC
C429
NC
R424 N C
VCC3.37
MSCL
adj_BACKLIGHT 7
NC
CS
R482 NC
R410 10K 1/16W 5%
100R 1/16W 5%
NC
R408
10K 1/16W 5%
PB2
PA[4..9]
PB0
DDC1_SDA4
VCC 3. 3
ZD 403
NC/M LVS0603M 04
1 2
R418 N C/100OH M1/16W
ZD 404
NC /MLVS0603M04
1 2
R453
NC
DET_CABLE 4
R469
2K2 1/16W 5%
VCTRL 7
R452
R420
VCC1.87
Max condition for LED:
1. Vcc = 3.3 V
2. Current = 12 mA
FW need to be modified.
R425
NC
PPWR_ON # 6
For All model
C416
0.1uF /16V
Mut e 7
R426 NC
10K 1/16W 5%
NC or 100R 1/16W 5%
C408
0.22uF 16V
DDC1_SCL4
VCC1.8
PB5
on_BACKLIGHT 7
R466
2K2 1/16W 5%
PA[4..9] 6
020
R407
10K 1/16W 5%
R413 100R 1/16W 5%
CMVCC14,6, 7
FB401
30OHM
VCC1.8
Q403
LMBT3906LT1G
EDID_CTRL 4
For ID2008 ID2009
C419
PB8
MSD A
LVDS
CMVCC1
R471 330R 1/10W 5%
DSUB_G+4
AVDD
R454
NC
R405 100R 1/16W 5%
Near to Connect
U403
LED_ORANGE/TOUCH VCC
R468 200R 1/10W 5%
DSUB_R+4
R426
KEY1
PB3
PB7
POWER_KEY #
PA[0..1]
R452 NC
DSUB_R-4
EE_WP
U402
R455
NC
LED_ORANGE/TOUCH VCC
CS
VCC3.3
U402
MX25L2026MI-12G
1
2
3
4 5
6
7
8
CS#
DO
WP#
VSS DI
CLK
HOLD#
VCC

20
PB0PB1
PA6
PB6
PA1
PA5
PB9
R434
330OHM1/4W
PB9
PA9
PA[0..1]
PB7
PA1
PANEL_VCC
PB8
2
PB4
PB3
PA4
PB0
PB2
Q404
LMBT3906LT1G
PB2
PB0
PA[4..9]
PA8
PB3
PB5
1
T99SRD*TVNN F
A1981Wx A
67Thursday , May 06, 2010
G3244-2-2 <
称爹 >
04.Output
G3244-2-2-X-8-100426
OEM MOD EL Size
Rev
Date Sheet of
TPV MO D EL
PCB NAME
称爹
T P V ( Top Victory Electronics Co . , Ltd. )
Key Component
絬 隔 瓜 絪 腹
PA4
PA0
R436
100K 1/16W 5%
PPWR_ON#5
AO3401L
PB2
PB3
PA5
D
PB4
PA5
PB[0..9]
FB402
120OHM
PB9
PA7
PA6
PB6
PB3
CN405
NC/CONN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
PB7
C420
0.1uF/16V
R433
10K 1/16W 5%
PB[0..9]5
2006-11-7 Add pull up 4K7 to MVCC
PA8
Q411
NC/AO4411
1 2 3 4
8 7 6 5
S S S
G
D D D D
PB5
PB6
PA[4..9]5NC/R477
150R 1/4W 5%
+
C421
100uF/25V
PANEL_VCC
PB2
CN403
CONN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
G
PA[0..1]5
PB8
PB3
PA4
PB7
PA0
PA8
PA9
C419
0.1uF/16V
PA9
PANEL_VCC
R435
4K7 1/16W 5%
PB1
Q405
AO3401
S
PB1
PB5
CMVCC 4,5,7
PB2
CMVCC
PA6
PA7
PA1
PB8
3
PPWR_ON#
PB4
PA0
PA7