Aopos Anypos200 User manual

Anypos200
User Manual
AOPOS SYSTEMS, S.A.

Anypos PointofService
Welcome
Thank you for purchasing our powerful Anypos!
With this Guide is to help you operate the Anypos.
About the Product
Anypos is an innovational design from Point of Sale terminals and Kiosk
with over decade of market experience and product development capability,
A full range of functions are designed, developed and produced to meet the
requirements of department store, supermarket, hypermarket, convenient
store, boutique shops, restaurants, theaters, railway, metro, school, and
government projects.
Checking the packaging list
After you unpack the Anypos, check that the following items are included.
If any item is missing or appears damaged, contact your dealer immediately.
1

Anypos PointofService
Identifying Components
This section describes the parts and connectors on the Anypos.
Front view
DESCRIPTION
1 15-inch TFT LCD and Touch screen
2 Magnet Stripe Reader（Option）
3 Power LED
4 HDD LED
5 IC Card LED（Option）
6 Power botton
7 Front Line-out jack（Option）
8 Speaker（Option）
9 RF card reader antenna（Option）
NOTE： When you use front Line-Out jack, no voise will be out
from the speakers.

2

Anypos PointofService
Rear view
DESCRIPTION
1 Back Cover Board
2 Main Base
3 The screw holes of customer display
4 The hole of line
Bottom Panel Ports
3

Anypos PointofService
DESCRIPTION
1 AC adapter connector
2 PS2 keyboard port
3 PS2 mouse port
4 Parallel port (LPT1)
5 VGA port
6 USB 1&2&3&4
7 10/100 NIC port
8 Microphone
9 Line-out
10 DC +12V Output OUT 12V
11 COM1 port COM1
12 COM2 port COM2
13 COM3 port COM3
14 COM4 port COM4
Attaching VFD Customer Display
1、Connect the customer
display through the
cable to customer
display port on the
bottom panel.
4

Anypos PointofService
2、Secure the display
with four supplied
screws.
Attaching the LCD Customer Display
1、Connect the LCD
customer display to the
VGA port and +12V
output port separately
through signal cable
and power supply
cable.
2、Secure the display
with four supplied
screws.
5

Anypos PointofService
Powering the Anypos on and off
1、Connect the power
cable to an electrical
outlet ,on the Anypos ,
Connect the adapter to
the AC adapter connector
2、Press the power button
on the underside of the
display panel. The power
LED turns on
3、There are 2 ways to turn off the Anypos：
1) Click “Start” button, and then “Turn Off Computer”, next
“Close”;
2) Use the main power button to turn off the power, for example
if the operating system you are using does not support power
down by the OS or if the system crashes or hangs.
Recommended turning off: 1)
Setup the Touchscreen
The touchscreen must be calibrated before in use.
After successful installation of diver, the following icons will appear on
your desk.
6

Anypos PointofService
Click on the “General Touch Touchscreen”, the system will enter calibration
interface.
Calibration, draw test tools and the linearity curve of the touchscreen were
list in this property page shown as below for user to do touchscreen
calibration and touch position test.User can do calibration or draw test by
pressing the function push buttons.
Linearization Curve
Linearization curve of the touchscreen is list in this page for reference and
trouble shooting purpose.
4 points calibration
Pressing this button, a new window will be popped-up at the location when
the touchscreen was mapped to area for this touch system to guide the user
do 4 points calibration.
User should follows the guide to touch and hold the blinking X symbol in
the calibration window until it does not blink to make sure that the utility
can gather enough data for computation.
7

Anypos PointofService
Clear and Calibration
Press this button to erase the 25 points calibration/linearization parameters
and force user to do 4 points calibration again. After 25 points calibration
data was clear, the 4 points calibration data will be invalid. It needs to do 4
points calibration.
Linearization
Linearization ( 25 or 9 points calibration ) function is used to compensate
the touchscreen linearity. After linearization completed, the linearity of the
touchscreen will be shown in the Linearity curve window.
Pressing this button, a new window will be popped-up at the location when
the touchscreen was mapped to area for this touch system to guide the user
do 25 points calibration. User should follows the guide to touch and hold
the blinking X symbol in the calibration window until it does not blink to
make sure that the utility can gather enough data for computation.
8

Anypos PointofService
Draw Test
This function is used for accuracy and performance check. Press this bu
and a new pop up window will be popped up in tton the location where the
hscreen was mapped to the touch system.
or
touc
COM1~COM4Ringfunctionselect
JP1 ：COM1/COM2 Ring function selector
JP2 ：COM3/COM4 Ring function selector
JP1and JP2 enable you to choose between 5V and 12V on COM1～CO
respectively. Since pin M4 9 on COM1～COM4 is reserved for switching
2V
between 5V and 1
Troubleshotting
Often after time spent troubleshooting, the problem is traced to something
as simple as a loose connection.
th Check the following before proceeding to e problem-specific solutions.
PROBLEM SOLUTION
The display screen is
dd mode, and adjust
the display brightness.
ark.
Make sure that the Power LED is on and
Anypos is not in suspen
The following mes
appears at boot up:
“Invalid system disk,
sage
R
eplace the disk, and
t
hen press any key”
uence in the BIOS setup
utility.
Ensure that an operating system is installed.
Check the boot seq
An unidentified
m
essage is displayed.
Reboot the terminal and run the BIOS Setup
U
tility. Confir
m
the Setup Utility parameters.
I
f the same message is displayed after booting
u
p again,
You cannot turn on the Check the AC adapter connection. Make sure
9

Anypos PointofService
10
t
erminal.
t
ha
t
the adapter LED is on. Otherwise，replace
t
he adapter
The scanner is not
w
orking
Check the scanner cable connection. Check
t
he scanner with another terminal to see if it
w
orks. If the same problem occurs, replace the
scanne
r
.
The screen is blank and
y
ou don't hear any beeps.
Check that the power cord is plugged into a
w
orking electrical outlet. Check that the
p
ower is on. (Press the power switch again for
confirmation.)
Only the cursor appears. Reinstall the operating system, and power on
t
he Anypos.
Audio problems Ensure the audio cable is not defective. The
m
ute is off.
Terminal is not working
at all
Wait 30 seconds and try again.
If still not working – Reboot the terminal.
Otherwise, have the Anypos serviced..
T
erminal is frozen Wait 30 seconds and try again.
If still not working – Reboot the terminal.
Otherwise, have the Anypos serviced.
Having the Anypos Serviced
If you are unable to solve the problem, you should have the Anypos
serviced. Pack the Anypos in the original carton. Include a description of
the problem and a checklist of the steps you took when trying to fix the
problem. The information may be useful to the service personnel. Return
the Anypos to the place you purchased it.