Apco HealthView HPSTube-FS User manual

388 Grant Street, SE, Atlanta, Georgia USA 30312-2227 Telephone [phone] Web: www.apcosigns.com IS353
10/13/2011
Unpack carton and check contents listed on this page before assembly. The soap dispenser is packaged separately, assemble the stand first and
attach the tube before installing the soap dispenser in the Tube. Follow the steps below to assemble the Tube.
Patent Pending
Step One: Attach steel Base Plate (A) to Lower Post (C). Locate bolt
(B) to join base to post, place a drop of Thread Locker (G) on bolt before
threading into post. Use hex wrench (H) provided to secure bolt.
Step Two: Remove white protective cap from threaded stud on lower
post and apply a drop of thread locker to stud. Attach Upper Post (E) by
threading tube on stud on Lower Post (C).
Step Three: Remove white protective cap from threaded stud on Upper
Post (E) and apply a drop of thread locker to stud. Attach Tube (F) by
threading on to stud. Note: Be sure to turn Tube until the post enters
tube bottom cavity completely and contacts the black friction pad.
Stanchion assembly is complete.
Installing Soap Dispenser: Remove top cap from Tube, remove green
tape. Place soap dispenser on foam lifters inside Tube.
Replace Tube Cap by depressing the Snap Buttons and placing cap flange
inside the tube, once cap is seated, turn cap until snap buttons engage.
Removing Cap: Compress one snap button while at the same time,
lift soap dispenser upward. Use thumb finger nail to press button completely
in. Cap removal may require practice as the snap button is designed to
be tamper proof.
Cap Replacement: Re-locking the lid is easily done by compressing
snap buttons and inserting lid and turning until buttons snap in place.
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
A. Base Plate
B. Bolt
C. Lower Post
D. Splice Connector
E. Upper Post
F. Tube
G. Thread locker
H. Hex Wrench
Description QTY/Assy
C.
A.
B.
D.
Apply thread locker here
Apply thread locker here
E.
F. Tube
Upper Post
Splice Connector
Lower Post
Base Plate
Bolt
Apply thread locker here
HPSTube Assembly
Complete
G.
APCO
HPSTube-FS Free Standing Stanchion
Assembly
Instructions
Push & Lift
H. 5/32” Hex Wrench
B.
1/4-20 x 1” Pan HD Socket - SS
Machine Screw
.5 ml medium strength
thread locker

388 Grant Street, SE, Atlanta, Georgia USA 30312-2227 Telephone [phone] Web: www.apcosigns.com IS353
10/13/2011
Unpack carton and check contents listed on this page before assembly. The soap dispenser is packaged separately (or customer
supplied). Whenever possible, anchor wall units where studs exist in the wall.
Patent Pending
Step One: Determine the desired dispenser height to the floor. Subtract
6” and mark the first hole location. Use the angle to match mark and locate
the second mounting hole.
Step Two: Attach steel mounting angle to wall.
Step Three: Position the Tube on the angle and thread the bolt into the
bottom of the Tube. Tighten bolt, the installation is complete.
Installing Soap Dispenser: Remove top cap from Tube, remove green
tape. Place soap dispenser on foam lifters inside Tube.
Replace Tube Cap by depressing the Snap Buttons and placing cap flange
inside the tube, once cap is seated, turn cap until snap buttons engage.
Removing Cap: Compress one snap button while at the same time, lift
soap dispenser upward. Use thumb finger nail to press button completely
in. Cap removal may require practice as the snap button is designed to be
tamper proof.
Place soap dispenser on foam lifters inside Tube.
Cap Replacement: Re-locking the lid is easily done by compressing
snap buttons and inserting lid and turning until buttons snap in place.
6”
C.
B.A.
C.
B.
A.
10.88”
4.76”
1”
6”
APCO
HPSTube-FS Wall Mounted
Assembly
Instructions
Push & Lift
1/4-20 x 1” Pan HD Phillip Head
Machine Screw
.5 ml medium strength
thread locker
#8 x 1.25” SMS - EZ- Anchor zinc
Distance to floor