Apera Instruments PH60 User manual

1
Premium Series PH60 pH Tester
User Manual
APERA INSTRUMENTS, LLC
aperainst.com
v7.7

2
Thank you for purchasing Apera Instruments PH60 Premium pH Tester. Please read this manual before use in
order to properly use andmaintainthe product.
For video tutorials, please go to support.aperainst.com
TABLE OF CONTENTS
1WHAT’S IN THE KIT................................................................................................................................................3
2KEYPAD FUNCTIONS..............................................................................................................................................3
3PREPARATION BEFORE USE ...................................................................................................................................4
4PH CALIBRATION ...................................................................................................................................................4
5PH MEASUREMENT ...............................................................................................................................................6
6PROBE CLEANING ..................................................................................................................................................6
7PROBE STORAGE ...................................................................................................................................................6
8PARAMETER SETTING............................................................................................................................................7
9ORP MEASUREMENT .............................................................................................................................................8
10 TECHNICALSPECIFICATIONS ..................................................................................................................................8
11 OTHER SPECIFICATIONS.........................................................................................................................................9
12 PROBE REPLACEMENT ...........................................................................................................................................9
13 NOTES .................................................................................................................................................................10
14 BATTERY INSTALLATION......................................................................................................................................10
15 TROUBLESHOOTING GUIDE .................................................................................................................................11
16 WARRANTY .........................................................................................................................................................12
ATTENTION
•Water droplets are added during production to maintain the moisture of the probe. This is normal
practice and should not be attributed to used product.
•Never use the product when it’s freezing cold. Let it warm to room temperature before using.
•There is a sensor shield on top of the pH sensor, protecting the glass bulb sensor from accidental
damage. You can detach the sensor shield when rinsing and cleaning the sensor as shown in the
graph below. Put back the sensor shield after cleaning.
Detach before cleaning
Sensor Shield

3
1 What’s in the Kit
2 Keypad Functions
Short press: < 2 seconds
Long press: > 2 seconds
1. Short press to turn on the tester and long press to turn off the
tester.
2. When turned off, long press to enter parameter setting.
3. In measurement mode, short press to turn on backlight.
4. In calibration mode, short press to cancel calibration.
1. In measurement mode, short press to switch between pH
and mV.
2. In settings, short press to change parameters
(Unidirectional).
1. Long press to enter calibration mode;
2. In calibration mode, short press to confirm calibration;
3. When reading is locked, short press to unlock.
Calibration Vials

4
3 Preparation Before Use
3.1 Pull out the battery insulation slip, and take off the probe cap.
3.2 Rinse off the probe in pure water (preferably distilled or deionized water. RO water or tap water is the
alternative) , then shake off excess water.
3.3 Perform at least a 2-point calibration at pH 7.00 and pH 4.00. For tutorial, refer to Section 5.
3.4 If the tester hasn’t been used for a long time (over 1 month), please soak the probe in the 3M KCL
soaking solution for at least 30 minutes, then calibrate it before test.
4 pH Calibration
4.1 How to Calibrate
4.1.1 Short press to power on.
4.1.2 Pour pH buffer solutions in the correspondent calibration vials to
about half volume.
4.1.3 Rinse the probe in pure water; Shake off excess water. Dip the
probe in the pH 7.00 buffer solution first, and make a quick stir in
the solution, then hold still.
4.1.4 Long press to enter calibration mode, screen will turn green
(Short press if you decide to quit calibration and return to
measurement mode).
4.1.5 Wait for the reading to stabilize (when stays on the screen), then
short press to start the 1st point calibration. After calibration is
completed, the tester will return to measurement mode.Icon will
appear at the bottom left of the screen, indicating a successful 1-point
calibration (middle point).

5
4.1.6 To calibrate 2nd point, use 4.00 pH buffer and repeat Step 5.1.3 to 5.1.5 (Do NOT turn off the tester
after you finish pH 7 calibration). will display next to , indicating a successful 2-point
calibration (low and middle points).
4.1.7 If necessary (target pH>8.00), calibrate 3rd point using 10.01 standard pH buffer and repeat Step
5.1.3 to 5.1.5, will show up next to and , indicating a successful 3-point calibration
(high, low, and middle points).
4.2 Notes about Calibration
a) The 1st point calibration must be 7.00 pH. Perform the 2nd and 3rd point calibrations (4.00, 10.01, 1.68,
or 12.45) immediately after the 1st point calibration is finished. Do NOT turn off the meter before you
calibrate 2nd or 3rd point. Otherwise, you will need to restart the calibration process with 7.00 pH first.
b) The pH 4.00 and 7.00 buffer solutions poured into the calibration vials can be used for up to 10 times
as long as they are not contaminated and the bottles are capped when not in use. pH 10.01 can only
be used for up to 5 times as it will lose its accuracy much faster. After that, replace the buffer solutions
in the calibration vials with new ones to keep the accuracy. Keeping the freshness and cleanliness of
calibration buffers is essential for accurate pH measurement.
c) The tester can perform 1 to 3 points of automatic calibration and can recognize 5 types of pH standard
solutions. For details, please refer to the following table:
Calibration
USA Series
NIST Series
Indication icon
Recommended
1-pt
7.00 pH
6.86 pH
Accuracy requirement
≥ 0.1 pH
2-pt
Option A
1st pt: 7.00 pH
2nd pt: 4.00 pH or
1.68 pH
Option A
1st pt: 6.86 pH
2nd pt: 4.01 pH or
1.68 pH
Range < 7.00 pH
Option B
1st pt: 7.00 pH
2nd pt: 10.01 pH or
12.45 pH
Option B
1st pt: 6.86 pH
2nd pt: 9.18 pH or
12.45 pH
Range >7.00 pH
3-pt
1st pt: 7.00 pH
2nd pt: 4.00 or 1.68 pH
3rd pt: 10.01 or 12.45 pH
1st pt: 6.86 pH
2nd pt: 4.01 or 1.68 pH
3rd pt: 9.18 pH or 12.45 pH
Range: 0 to 14.00 pH

6
5 pH Measurement
5.1 How to take pH measurements
Short press to power on the tester. Rinse the probe in pure water,
shake off excess water. Dip the probe in your sample solution and make a
quick stir, then hold still. Record the reading after it is stabilized
( appears and stays on the screen).
5.2 Pure Water pH Measurement
When testing pure water like tap water, drinking water, RO water and
distilled water, it will take longer for the readings to get fully stabilized
(typically 1-5 minutes). Please be patient. If still not working, add Apera
3M KCL (AI1107) to your pure water at the ratio of 1:1000 (e.g. 1 ml KCL to 1000 ml water) to accelerate
stabilization while minimizing pH change. If the accuracy is not meeting your requirement, please contact us
at [e-mail] to find the specialized meter designed for pure water pH test.
6 Probe Cleaning
6.1 The tester is only as accurate as the probe is clean. Always thoroughly rinse off the probe before and
after each measurement with pure water in a container or with a wash bottle.
6.2 For tough contaminants, detach the sensor shield, soak the probe in Apera probe cleaning solution
(AI1166) or detergent water for 30 minutes. Then use a soft brush to remove the contaminants.
Afterwards, soak the probe in 3M KCL soaking solution for at least 1 hour. Rinse it off, then re-
calibrate the tester before using again.
7 Probe Storage
7.1 Under regular usage (daily or weekly use), make sure the probe cap is wet, and tightly close the cap
with the O-ring.
7.2 For long-term storage (you are not going to use the product for a while), add 3M KCL soaking solution
to the Fill line in the probe cap and store the probe in it. Close on the probe cap tightly with the O-
ring.
7.3 If you find white crystals inside or outside the probe cap, it is perfectly normal. It is the 3M KCL
soaking solution that crystalizes over time by its nature. Just rinse them off and add in new soaking
solution. This chemical is not poisonous nor dangerous, and the probe’s performance will not be
affected at all.
7.4 NEVER store the probe in pure water like tap, RO, distilled, or deionized water as they could damage
the pH probe. Pure water is only for rinsing the probe.

7
8 Parameter Setting
8.1 Setup Menu
Symbol
Contents
Parameter
Factory Default
P1
Select pH buffer solution
USA –NIST
USA
P2
Low value measurement alarm setting
0 to 14.00pH
0
P3
High value measurement alarm setting
0 to 14.00pH
14.00
P4
Select automatic lock
Off –On
Off
P5
Select backlight
Off - 1 - On
1
P6
Select temperature unit
℃- ℉
℉
P7
Restore to factory default
No –Yes
No
8.2 Parameter Setup
When turned off, long press to enter parameter settings →Short press to switch P1-P2-P3
…P7 →Short press to select parameter (selected parameter starts flickering) →Short press
to change parameter →Short press to confirm the change →Long press to go back to
measurement mode.
8.3 Parameter Setting Instruction
8.3.1 Select standard pH buffer solution (P1):
There are two options of standard buffer solutions: USA series and NIST series. Factory default is USA series,
for details see clause 5.2.
8.3.2 Alarm Function (P2&P3)
Examples:
■Alarm triggered when measurement ≤3.20 pH:
Preset lowest value (P2) = 3.20 pH, highest value (P3) = 14.00 pH, when measured value ≤ 3.20
pH (stable displays on screen); screen turns red.
■Alarm triggered when measurement ≥8.60 pH:
Preset highest value (P3) = 8.60 pH, lowest value (P2) = 0.00 pH, when measured value ≥ 8.60 pH
(stable displays on screen); screen turns red.
■Alarm triggered when measurement ≤3.20 pH or ≥ 8.60 pH
Preset lowest value (P2) = 3.20 pH, highest value (P3) = 8.60 pH, when measured value is lower
than 3.20 pH or higher than 8.60 pH (stable displays on screen), screen turns red.

8
8.3.3 Automatic Lock (P4)
Select “On” to activate auto lock function. When reading is stable for more than 10 seconds, the tester will
lock the value automatically, and HOLD icon will display on LCD. Short press key again to cancel the lock.
8.3.4 Backlight (P5)
“Off”-turn off backlight, “On”-always turn on backlight, “1”- backlight will last for 1 minute.
8.3.5 Temperature Unit (P6)
Select between C˚ and F˚.
8.3.6 Factory default setting (P7)
Select “Yes” to recover instrument calibration to the theoretical value (pH value in zero potential is 7.00pH,
slope is 100%), parameter setting return to initial value. This function can be used when instrument does not
work properly in calibration or measurement. Calibrate and measure again after recovering the instrument to
factory default status.
9 ORP Measurement
ORP stands for Oxidation-Reduction Potential. ORP is a measure of the cleanliness of the water & its ability to
break down contaminants. An ORP probe is needed to test ORP (sold separately, SKU: AI1207).After powering
on the tester, press to enter ORP mode (mV). Rinse the probe in distilled water and dry it. Dip the probe
in your sample solution, make a quick stir, and hold still. Record the reading after it is fully stabilized.
10 TechnicalSpecifications
pH
Measuring Range
-2.00 –16.00 pH
Resolution
0.01pH
Accuracy
±0.01pH ±1 digit
Calibration Points
1 –3 points
Automatic Temperature Compensation (ATC)
0 –50˚C
(32 –122˚F)
ORP (mV)
Measuring Range
± 1000mV
Resolution
1mV
Accuracy
±0.2% F.S
Temp.
Measuring Range
0 –50˚C (32 –122˚F)
Resolution
0.1˚C
Accuracy
±0.5˚C

9
11 Other Specifications
Screen
3-color LCD screen,
Blue: Measurement; Green: Calibration; Red: Alarm
Reading Lock
HOLD
Low-Voltage Warning
flashing, reminder of battery replacement needed
Auto. Power-Off
In 8 minutes without operation
Waterproof Rating
IP67
Power
DC3V, AAA alkaline batteries×4
Battery Life
Operation up to 2000 hours
Dimension& weight
Tester: 40×40×178mm/133g; Case: 255×210×50mm/700g;
12 Probe Replacement
12.1 Every pH probe gradually loses its sensitivity and will eventually fail. A typical service life of a pH probe
is 1-2 years depending on many factors such as frequency of use, nature of test samples, and how well
it is maintained, etc. Apera Instruments recommends replacing the pH probe every 1 to 2 years to
guarantee the optimal performance.
12.2 To replace a probe: 1) Take off the probe cap; 2) Screw off the probe
ring 3) Unplug the probe; 4) Plug in the new replacement probe (pay
attention to the probe’s position); 5) Screw on the probe ring tightly.
Soak the probe in 3M KCL for 5-15 minutes. Then perform calibration
before testing.
12.3 The replacement probes compatible with PH60:
•AI1201 PH60-E (Regular pH glass bulb probe for general water solutions)
•AI3711-E PH60-DE (Double-junction pH glass bulb probe for complex solutions)
•AI1205 PH60S-E (Spear pH probe for soft-solids pH testing)
•AI1203 PH60F-E (Flat pH probe for surface pH testing)
•AI1207 ORP60-E (ORP probe)

10
13 Notes
a) Avoid testing in very high (>113°F) or very low (<41°F) temperature solutions as it will cause greater
measurement error and potential damage to the probe. Test your samples and perform calibration
close to room temperature as much as possible.
b) NEVER store the probe in pure water like tap, RO, distilled, or deionized water as they could damage
the pH probe. If this happens, immediately soak the pH probe Apera 3M KCL soaking solution
overnight, then re-calibrate it before using. Pure water is only for rinsing the probe.
c) Never use your finger to touch the glass membrane or use other material to rub it. Doing so could
generate static electricity and cause measurement errors. Never test oily liquids.
d) Make sure the battery cap is completely closed with the red O-ring. Otherwise, the waterproof rating
could be compromised.
14 Battery Installation
Please install batteries according to the following steps. *Please note direction of batteries: All
POSITIVE SIDES (“+”) FACING UP. (Wrong installation of batteries will cause damage to the
tester and potential hazards)
+
+
+
+
-
-
-
-
① Pull the battery cap up
② Slide the battery cap along to the direction of arrow
③ Open the battery cap
④ Insert the batteries (ALL POSITIVE SIDES FACING UP) (see graph)
⑤ Close the battery cap
⑥ Slide and lock the battery cap along to the direction of arrow
⑦ Fit the tester’s cap while making sure to push all the way down. The
tester’s waterproof design may be compromised if the cap is not fitted
correctly.

11
15 Troubleshooting Guide
Trouble Reason How to fix
Pressing too soon
(showing )
Wait for to stay on the screen before pressing
Incorrect standard solutions
(showing )
Reboot tester, calibrate pH 7 first, then pH 4. For details refer to
Section 5.2 (a)
Poor quality standard solutions
(showing )
Replace with fresh and clean standard calibration solutions made
by legitimate scientific instrument manufacturers.
Contaminated probe
(showing )
Use a soft brush to clean the probe with Apera probe cleaning
solution or detergent water.
Aged probe
(showing ) Replace the probe.
Dried-out probe
(showing ) Soak in Apera 3M KCL soaking solution for at least 30 minutes.
Probe is not fully submerged
(showing )
Make sure the probe is immersed in the solution at least 1 inch.
Air bubbles around the sensor shield
(showing )
Make a quick stir in the solution to remove air bubbles.
Contaminated probe
Use a soft brush to clean the probe with Apera probe cleaning
solution or detergent water.
Clogged junction
Use a soft brush to clean the probe with Apera probe cleaning
solution or detergent water, then soak it in Apera 3M KCL soaking
solution overnight.
Aged probe Replace the probe.
Testing pure water like
tap/drinking/RO/distilled water
Be patient, wait for 1-5 minutes to reach a fully stabilized reading.
If still not stabilizing, add Apera 3M KCL solution to test water at
1:1000 ratio.
Broken probe
If you don’t find any visible damage of the probe, contact us for
warranty fulfillment; If there is visible damage, replace the probe.
Instrument defect Contact us for warranty fulfillment
Probe is not fully submerged in the
solution
Make sure the probe is immersed into solution at least 1 inch.
Air bubbles around the sensor shield Make a quick stir in the solution to remove air bubbles.
Probe is not properly connected or
the connector is broken.
Check the probe’s connector, make sure it’s not broken and is
correctly connected. Align the probe and instrument correctly
before plugging in. Never force it. Ensure that the probe connector
is not exposed to the air too long.
Aged probe Replace the probe.
Air bubbles around the sensor shield Make a quick stir in the solution to remove air bubbles.
Clogged junction
Clean the probe with cleaning solution, then soak it in 3M KCL
storage solution overnight
Comparison with other testers, test
strips, or drop tests
To compare accuracy with other testers, make sure to perform
calibration for all testers in the same standard, then test another
standard. Whichever gives more accurate reading is the more
accurate one. Test strips or drop tests’ accuracy is not comparable
to pH meters’.
Poor quality standard solutions
Replace with fresh and clean standard calibration solutions made
by legitimate scientific instrument manufacturers.
The probe is not suitable for your
appliacation.
Contact us to find the most appropriate product for your specific
application.
Calibration is successful,
but reading is not
accurate
Cannot calibrate
Reading is always slowly
changing, won’t stabilize.
Display similar readings
in any solutions or
always display 7.0 pH
Reading keeps jumping

12
16 Warranty
We warrant this instrument to be free from defects in material and workmanship and agree to repair or
replace free of charge, at option of APERA INSTRUMENTS, LLC, any malfunctioned or damaged product
attributable to responsibility of APERA INSTRUMENTS, LLC for a period of TWO YEARS (SIX MONTHS for the
probe) from the delivery.
This limited warranty does NOT cover any damages due to:
Accidental damage, transportation, storage, improper use, failure to follow the product instructions or to
perform any preventive maintenance, unauthorized repair or modifications, normal wear and tear, or other
external causes or actions beyond our reasonable control.
To get the fastest warranty fulfillment, go to support.aperainst.com and click “New Support Ticket” on the
upper right corner. Type your email in the requester field, “Warranty” in the Subject field, and then input the
following information in the description field:
•Your full name
•Product model that needs warranty fulfillment
•Serial number of the product (can be found on the back sticker of the tester body)
•What problem or issue you had experienced with the product
•Attach a photo of your proof of purchase
•Attach a photo of the problematic product
Then click Submit. One of our customer care specialists will help you fulfill the warranty within one business
day.
APERA INSTRUMENTS, LLC
Address: 6656 Busch Blvd, Columbus Ohio 43229
Tel: [phone]
Email: [email protected]
Website: aperainst.com