Aqua Lung Titan Service manual

Aqua Lung America • 2340 Cousteau Court • Vista, CA 92081 • [phone]
Aqua Lung America
TECHNICAL BULLETIN
Should you have any questions regarding this issue,
please contact our customer service department at:
(877) 253-DIVE
Feb 10, 2011
No. 31
SUBJECT: Titan / Calypso Opening Effort Improvement
PRODUCTS AFFECTED: The regulators in question are the
2010 models of Titan, Calypso and Octopus, references:
128500, 128700, 128560, 128540 and 128550
We have been informed that certain Titan and Calypso second stages (2010 models)
require an inhalation effort slightly greater than normal. Tests have shown this inhala-
tion effort is due to the quality of the crown 128621 sealing surface. In a constant goal to
improve the quality of our products, we have modied the crown material and improved
the sealing surface area. This new material is easily recognizable by its blue color, as op-
posed to the current gray crown.
NEW
CROWN
CURRENT
CROWN
This modication provides a better seal with the seat, allowing the technician to set the
crown at its ideal position for optimal inhalation effort.
Corrective Action
This problem only concerns a few of the Titan, Calypso and Octopus regulators included in a batch
whose the serial number begins by the letter "A" and with a serial number lower than 100801.
We recommend systematically replacing the crown during the annual servicing/inspec-
tion of these regulators and also for every regulator from customer returns which would
have a high inhalation effort.
To facilitate this operation, we have created a kit reference 128698 which includes a new
blue crown with o-ring and a MP seat. Please call our Customer Service Department at
877-253-3483 to request kits. Please be patient with us as we will limit the number of kits
until our supply gets caught up.
Use the procedure below to install the new crown, this was taken from the technical
manual of the Titan/ Calypso second stage:

Aqua Lung America
CROWN REPLACEMENT PROCEDURE
1 Slide back and hold the hose locker (12), turn the swivel nut coun-
ter-clockwise to remove the MP hose (28) from the second stage.
9
Fit a new, lubricated o-ring
(11) onto the crown (10).
2
Remove the front cover (1) by rst pulling the retaining loop
over the venturi knob (17). Lift the cover off the front of the sec-
ond stage and then rotate the cover out of the way. Remove the
diaphragm washer (2) and diaphragm (3).
4 Pull the venturi knob (17)
from the case (5).
5 Locate the tab on the ring locker (14). With your nger, pull the
tab into the slot on the hose locker (12) while turning the crown
holder assembly (8-14) counter-clockwise by hand. Remove the
crown holder assembly from the case (5).
6
Carefully slide out the valve
insert assembly (18-24)
from the case (5). Take care not
to damage the lever.
3
To remove the venturi (4),
use your nger to push in
the release tab on the venturi
knob (17) while lifting up on the
venturi.
7
Use a medium blade screw-
driver and carefully turn the
crown (10) counter-clockwise
approx. 6-7 turns to disengage
the crown.
8
Carefully insert the pin end of the seat extraction tool (pn
109437) through the crown holder (8) so that you can push the
crown (10) out.
CAUTION: Use of the wrong size blade screwdriver can cause per-
manent damage to the crown which will require it to be replaced.
Conrm the screwdriver blade ts the crown securely.
CAUTION: No tools are required to remove the MP hose from the
second stage. Use of tools or excessive force may cause damage
to the associated parts.

Aqua Lung America
1 0 Push the crown (10) into
the larger threaded end
of the crown holder (8). Using
the seat installation tool (pn
127686), engage the crown and
turn clockwise until the tool dis-
engages from the crown. This is
the pre-set for the crown.
1 1 Fit a new MP seat (18) into the poppet (19). Replace the
entire valve insert assembly (18-24) into the case (5).
1 2 While holding the valve insert assembly (18-24) inside the
case (5), hold the lever (22) down and thread the crown
holder assembly (8-14) clockwise into the valve insert until the tab
on the ring locker (14) locks into the notch on the case.
1 3
Slide the tab on the ring locker (14) out of the notch on the
case (5) and rotate the crown holder (8) one more revolution
until the ring again locks into the notch. Conrm the crown holder
will not turn anymore.
1 4 Attach the swivel end of the MP hose (28) to the second stage by turning the swivel nut clockwise until it is secured
in place by the hose locker (12). Finally, attach the rst stage to a
test bench or a fully charged 3000 psi (206 bar) cylinder. Slowly
pressurize the rst stage.
1 5 Using the crown/lever adjustment tool (pn 125727), slide the
tool across the top of the case (5). The lever (22) must
touch the cutout on the tool without causing any air loss. This
lever setting is 2.5mm above the case edge. If the second stage
leaks the lever is set too high, use a ¼” nut driver to adjust the lock-
nut slightly CCW. If the lever is not touching the cutout in the tool it
is too low, turn the locknut CW to raise it. Once the lever height has
been conrmed, turn off the air supply and purge the regulator and
remove the MP hose (28) from the second stage.
1 6 Insert the venturi knob (17) into the opening on the right side
of the case (5) with the locking tab facing upward.
1 7 Insert the venturi (4) into the cutout in the venturi knob (17).
You should hear it “click” as the venturi locks into place.
CAUTION: Failure to perform this last step and tighten the crown
holder all the way will cause a leak at rst pressurization.
ADJUSTING LEVER HEIGHT

Aqua Lung America
1 8 Fit the diaphragm washer (2) evenly into the front of the dia-
phragm (3). Place the assembly into the case (5).
1 9 Fit the front cover (1)
onto the front of the case
(5) pulling the retaining loop
over the venturi knob (17). Visu-
ally inspect the cover to conrm
that it is seated evenly all the
way around.
NOTE: If your facility is equipped with a test bench, perform the tests
before installing the mouthpiece. General instructions for performing
bench tests are located in the Technical Maintenance Manual.