Aqua-Marina Breeze User manual

USER MANUAL
INFLATABLE
STANDUP PADDLE BOARD
EN

2
SAFETY
There is a risk of serious injury or death from drowning. Paddle
sports can be very dangerous and physically demanding. The
user of this product acknowledges, understands, and assumes the
risks involved in paddle sports. Observe the following warning
labels and safety standards carefully whenever using this product.
GENERAL PADDLING INFORMATION
This manual has been compiled to help you operate your
Inflatable Stand Up Paddle Board (Hereinafter referred to as ISUP)
with safety and pleasure. It contains details of the ISUP, the
equipment supplied, and information on their operation. Please
read it carefully and familiarize yourself with the ISUP before
using it.
For your own safety and that of your equipment,
make sure to take the following precautions.
Failure to follow warning notices and instruction
may result in property damage, serious injury or
death.
WARNING
AM Official Site AM HOW-TO Guide AM Service Center List

3
WARNING LABEL INSTRUCTIONS
130kg
286lbs
MANDATORY INSTRUCTION
• Wear personal flotation device• Read instructions first• Fully inflate all air chambers• Numbers of users• Max. load capacity• Safe distance to shore 150 m (492.1’)PROHIBITION INSTRUCTION
• Do not use in white water (except BT-22RP)• Do not use in breaking waves
(except BT-22WA)
• Do not use in offshore current• Do not use in offshore wind•
Not for children 14 years old and below (except BT-22VIP)
ATTENTION / DANGER / WARNING
• Design working pressure• No protection against drowningMANDATORY INSTRUCTION
• Swimmers only• Always supervise children in waterPRODUCT SERIAL NUMBER
• Item No.• Manufacturer information

TOURING
4ALL AROUND
MODEL
SIZE
FIN
VOLUME
MAX. RIDER WGT
MAX. AIR PRESSURE
15 PSI15 PSI
1 CENTER FIN 1 CENTER FIN
RACING
1 RACING FIN
18 PSI
14‘0“27“6“
427 cm69 cm15 cm
BT-21RA02RACE
360L352LBS160KG
12‘6“27“6“
381 cm69 cm15 cm
BT-21RA01RACE
320L330LBS150KG
1 RACING FIN
15 PSI
10'2"31''4.7''
310cm
78cm
12cm
BT-22COP
CORAL
230L231LBS105KG
1 RACING
FIN
15 PSI / 10 PSI (center chamber)
11‘6“31“6“
350 cm79 cm15 cm
BT-21HY01HYPER
330L330LBS150KG15 PSI
11‘6“31“6“
350 cm79 cm15 cm
BT-22CTP
CORAL
TOURING
328L286LBS130KG
12‘6“32“6“
381 cm81 cm15 cm
BT-21HY02HYPER
370L374LBS170KG
TOURING
9'10"30''4.7''
300cm
76 cm
12cm
BREEZE
BT-21BRP
220 L220 LBS100 KG
10'4"31''6''
315 cm79 cm15 cm
BT-21VAPVAPOR
310L308LBS140KG
10'10"32''6''
330cm
81cm
15cm
BT-21FUPFUSION
320L330LBS150KG
12'0"33''6''
366 cm
84cm
15cm
BT-21MOPMONSTER
380L374LBS170KG
10'6"32''6''
320 cm81 cm15 cm
BT-21BEPBEAST
300L308LBS140KG
11'2"33''6''
340 cm84 cm15 cm
BT-21MAPMAGMA
330L330LBS150KG
12'0"34''6''
366 cm
86 cm15 cm
BT-21ATPATLAS
390L396LBS180KG

5FITNESS
KID
MULTI-PERSON FISHING
1 FIBERGLASS
RACING FIN
8‘8“30“4“265 cm75 cm10 cm
BT-22WA
WAVE
18 PSISURF
161L209LBS95KG1 SURF
CENTER
FIN + 2
SIDE FINS 8 PSI18‘1“60“8“550 cm152 cm20 cm
BT-20ME
MEGA
1400L1433LBS650KG5
CENTER
FINS
1
RACING
FIN
18 PSI22‘0“34“8“670 cm87 cm20 cm
BT-20AS
AIRSHIP
RACE
1000L1014LBS460KG12‘2“32“6“370 cm82 cm15 cm
BT-21ST01
SUPER
TRIP
15 PSI400L462LBS210KG1
CENTER
FIN 14‘0“34“6“427 cm86 cm15 cm
BT-20ST02
SUPER
TRIP TANDEM
18 PSI500L507LBS230KG2
CENTER
FINS 10‘10“38“6“330 cm97 cm15 cm
BT-20DRP
DRIFT
15 PSI (board) / 3PSI (side air
chambers)
284L286LBS130KG1
CENTER
FIN
10‘6“33“6“320 cm84 cm15 cm
BT-22BL
BLADE
350L330LBS150KG
WINDSURF
1 CENTER
FIN + 1
DAGGER
FIN
18 PSI8‘0“28“4“244 cm71 cm10 cm
BT-22VIP
VIBRANT
15 PSI132LBS60KG140L1
CENTER
FIN
RIVER
9‘6“33“6“
289 cm84 cm15 cm
BT-22RP
RAPID
18 PSI
1 RIVER FIN
+ 4 FIXED
FINS
300L286LBS130KG
15 PSI11‘0“36“6“336 cm
91 cm15 cm
BT-21DHP
DHYANA
352LBS160KG360L8‘2“35“6“250 cm90 cm15 cm
BT-20PC
PEACE
340L330LBS150KGYoga Dock BT-19YD
Outer Diameter: 290cm/9'6"Inner Diameter: 170cm/67"Thickness: 12cm/4.7”1
CENTER
FIN
/
RACING
14‘0“25“6“
427 cm63.5 cm15 cm
BT-22RE
RACE ELITE
330L330LBS150KG18 PSI
DHYANA
RECOMMENDED
INFLATION18PSI
1.25BAR
WARNING:KEEPUNDERSHADEWHENNOTINUSE
WITHAWORKINGPRESSURELESSTHAN10PSI.
45°
LOCK
L
I
F
E
V
E
S
T
R
E
C
O
M
M
E
N
D
E
D
A
L
W
A
Y
S
W
E
A
R
A
L
E
A
S
H
DOUBLELAYER QUADRUPLE STRINGERTECH
RACE
ELITE

OrientalRecreational Products (Shanghai) Co., Ltd.
1699Daye Road, Fengxian Shanghai, China 201402
15psi/ 1.0bar
NOPROTECTION AGAINST DROWNING
AUCUNEPROTECTION CONTRE LA NOYADE
KEINSCHUTZ GEGEN ERTRINKEN
SINPROTECCIÓN CONTRA EL AHOGAMIENTO
Item No.: BT-21HY01
CN-O RP
95kg
209lbs
1 0
SWIMMERSONLY
LESNAGEURS SEULEMENT
NURFÜR SCHWIMMER
SÓLOLOS NADADORES
6
High pressure
recessed valve
High pressure
recessed valve
Cargo bungee
cord
D-ring
D-ring
Cargo bungee
cord
Heavy-duty
neoprene carry
handle
EVA deckKick padSlide-in
center fin
Actual configuration may vary upon different models.
Added
Chamber
D-ring
Bungee cord
stopper
Bungee cord
stopper

*Actual configuration may vary upon different models.
7
ACCESSORIES
Zip Backpack
Leash
(except Super Trip/ Super Trip Tandem/Mega/Airship Race/Peace/Yoga Dock)
Paddle Holder
Paddle Holder
(Only for Dhyana)
Paddle (excluded from Race/Race Elite/Hyper/Rapid/Super Trip/Mega/Airship Race/Blade/Wave/Peace/Super Trip Tandem)Board Strap
Double-Action Pump -
LIQUID AIR V1(Mega/Airship Race/ Super Trip Tandem x 2)(Coral/Beast/Magma/Atlas/Hyper/Coral Touring/Race/Race Elite comes with LIQUID AIR V2)Center Fin (Mega x 5/Super Trip Tandem x 2/Wave x 3/ Blade x 2)Cargo Bungee Cord
(except Wave) (Hyper x 2)Carry Bag Repair KitStraps x 3(Only for Dhyana)
Fishing Rod Holder x 2STANDARD
DRIFT MEGA/YOGA DOCK
PADDLE
CORAL/YOGA/CORAL TOURING
WONDER
IS
ALL-AROUND

INSTRUCTION FOR ASSEMBLING
AND DISASSEMBLING
8INFLATION Push valve button in and turn 90 degrees.
Open the valve cap by twisting
counter-clockwise. Ensure the
valve is clear from debris, sand, or
dirt before releasing.
Valve button popping up to the “UP position” for inflation.Valve button locked in “DOWN position” for deflation.UP POSITIONUP POSITION DOWN POSITIONDOWN POSITION
OR
Attach – Attach the
pump hose to the pump
and secure it tightly.
Connect – Attach the
end of the pump
hose to the valve and
twist 45° clockwise to lock in place.
Save Effort – As
pressure builds, keep
arms extended and bend the knees to
power for less effort.

After inflation, return the valve cover and tighten in
clockwise direction to lock in place.
12PSI minimum (8PSI for MEGA/ 10PSI
for HYPER inner chamber) for proper
inflatable boards operation and 15PSI
maximum (18PSI for SUPER TRIP
TANDEM/ RAPID/ RACE/ RACE ELITE/
WAVE/ BLADE/ AIRSHIP RACE ). Over
inflation will void your warranty.
9Fast Inflation – Use DOUBLE
ACTION position by closing
the air-tap to pump the
board up to 7-10 psi.Easy Inflation – Switch to
SINGLE ACTION position
by removing the air-tap for
easier inflation.
Fast Inflation – Use DOUBLE
ACTION mode with the top
cap displaying “2” to pumpthe board up to 7 - 10 psi.Easy Inflation – Rotate the
switch to SINGLE ACTION
mode with the top cap
displaying“1” for easier inflation.
Max. Pressure –
Keep pumping the board until you
reach 15-18 psi.LIQUID AIR V2
LIQUID AIR V1
Note: Gauge will not respond until reaching 4psi. Just keep pumping for 2-3 minutes!

FIN INSTALLATION
10Slide-in Center Fin System
• Electric Pumps can be used to inflate board up to 80-90%. However, the remaining pressure required should be achieved by using the hand
pump to avoid over-inflation.
• Do not use air compressors as this voids warranty of board.• Before long trips, ensure the board has been inflated and has maintained pressure for a minimum of 24 hours.PRECAUTION & TIPS
For Double Chamber Board ( HYPER )
For best performance, the double
chamber should always be inflated to
ensure the highest stiffness and safety.
• Inflate the inner chamber up to 10 PSI.• Inflate the outer chamber up to 15 PSI.10psi
15psi
SLIDE - Slide in
the large Center
Fin to the fin base.
INSERT - Insert
the push-in pin.
Do not leave your board under direct sunlight as this may cause
over-inflation.
Please keep the board under shade when not in use with a working pressure
NO MORE THAN 10psi, or leave your board in a cool dry place. Remember to check the air pressure before and after use, and deflate your
board when necessary.
Warning:

Press & Click Fin System ( WAVE )
NOTE: Install the WAVE side fins as suggested below.US Fin System ( RACE ELITE ) 11SLOT IN - Align the fin
base into the fin box slot and slide to the front edge.
Left Right
WASHER - Place the washer into the
fin box and slide it to the front.SLOT IN - Align the fin base into the fin slot and slide to the rear of the fin
box.LINE UP - Push the fin down and line
up the washer hole with the screw.
SCREW - Secure firmly by screwing.
PRESS - Keep pressing the button on the rear
and push the fin down.
SNAP - Lock the fin in
place with the snap.

12Valve Open – Open the valve cap and twist the valve button for “DOWN POSITION”. Ensure the valve is clear from debris, sand, or dirt before releasing.Deflate (by hands) – Roll the board from nose to tail to squeeze the air out.
Deflate (by pump) – Use the pump
on “DEFLATE” position.
RECOMMENDED
INFLATION
15PSI
1.0BAR
WARNING:KEEPUNDERSHADEWHEN NOT IN USE
WITHAWORKINGPRESSURELESS THAN 10 PSI.
45°
LOCK
L
I
F
E
V
E
S
T
R
E
C
O
M
M
E
N
D
E
D
A
L
W
A
Y
S
W
E
A
R
A
L
E
A
S
H
Roll – Roll the board around the
pump. Make sure the pump is
settled in the middle.
Pack – Use the webbing strap to
secure the neatly rolled board in place,
but do not overtighten the strap. Place
the accessories in the pocket.
(for LIQUID AIR V1 only）DEFLATION

13PADDLE ASSEMBLY
I
Front
Correct Incorrect
Front
TIP:
Start to fold from here.
NOTE:
For RACE board, we still recommend
rolling your board around the pump.
Alternatively, please fold in the dotted
line as below (Fig. A) to avoid bending
the side rail pads.
RECOMMENDED
INFLATION18 PSI
1.25BAR
WARNING:KEEPUNDERSHADEWHENNOT IN USE
WITHAWORKINGPRESSURELESSTHAN 10 PSI.
45°
LOCK
L
I
F
E
V
E
S
T
R
E
C
O
M
M
E
N
D
E
D
A
L
W
A
Y
S
W
E
A
R
A
L
E
A
S
H
(Fig. A)

14• DUAL-TECH
2-in-1 iSUP & Kayak Paddle
• ACE
Adjustable Aluminum
iSUP Paddle for Kids• SPORTS III
SPORTS III CORAL
Adjustable Aluminum
iSUP Paddle
• SOLID
Adjustable Fiberglass
iSUP Paddle
• CARBON GUIDE
Carbon / Fiberglass iSUP Paddle
• CARBON PRO
Carbon iSUP Paddle
3 PCS ADJUSTABLE 2 PCS ADJUSTABLE 2-IN-1
• CARBON X
2-section Carbon
iSUP Paddle
II B0303012B0303622B0303624B0303013B0303014B0303015B0303016B0303011Ensure the center line of the
scale is aligned with the
indicator on clamp.
Adjust tightness by rotating the
hasp to reduce any play.
Secure spring pin.
SPORTS III CORAL
CLAMP SYSTEM
SPRING PIN SYSTEM
NOTE: Always drain the water left in the paddle shaft
after each use.

COIL/SURF/RIVER LEASH INSTALLATION
STANDARD LEASH INSTALLATION 15HOW TO WEAR A SAFETY LEASH
WAIST
ANKLE
STANDARD LEASH
RIVER LEASHCOIL LEASH
B0303023B0303025SURF LEASH
B0303024B03027651 1
4 53
2 2 3

HOW TO TAKE CARE OF ISUP BOARD
FAQs (Frequently Asked Questions)
Q: How much air should I pump into my board, and how long does it take
to inflate?
A: The maximum pressure is 15 – 18 PSI (8 PSI for MEGA, 10 PSI for HYPER inner chamber, 3 PSI for DRIFT side chambers), any higher you risk over inflating and
damage. Depending on the size of your board it can take anywhere from 5 to 8 minutes.
Q: When detaching the pump from the board, the air starts to release from
the valve. How do I stop this from happening?
A: The air is releasing as the valve spring pin has been left in the deflating position.
Simply push down and turn the pin until it lifts up into the inflation position and
stops air from releasing; continue to inflate the board until up to pressure.
16AVOID DIRECT
SUNLIGHT
Keep the board under shade when not in use
with a working
pressure less than
50%-60% of the max. air pressure.
NO DRAGGING
Don’t drag the board as sharp debris may
puncture it.
KEEP IT DRY
Dry the board after each
use, especially before
storing to avoid mould
damage.
DON’T USE AN AIR
COMPRESSOR
You can easily over-inflate the board by using an air
compressor and void the
warranty.
FREQUENT USE
Use the board frequent-
ly as long-term storage
may cause adhesive
failure.
AVOID TEMPERATURE
EXTREMES
Keep the boards sheltered away from temperature
extremes and humidity. Store at room temperature
between 0℃ - 40℃.
REGULAR
MAINTENANCE
Regularly check for
cracks, scrapes, or any
other issues and repair
if necessary.
CLEANING
Clean the board after
each use with freshwater
and mild soap.
RECOMMENDED INFLATION
15PSI
1.0BAR
WARNING:KEEPUNDERSHADE
WHENNOTINUSE
45°
LOCK
L
I
F
E
V
E
S
T
R
E
C
O
M
M
E
N
D
E
D
A
L
W
A
Y
S
W
E
A
R
A
L
E
A
S
H
RECOMMENDED
INFLATION
15PSI
1.0BAR
WARNING:KEEPUNDERSHADE
WHENNOTIN
45°
LOCK
L
I
F
E
V
E
S
T
R
E
C
O
M
M
E
N
D
E
D
A
L
W
A
Y
S
W
E
A
R
A
L
E
A
S
H
DO’S DON’TS

171. Clean the area around the cut or puncture using acetone or M.E.K.2. Draw the outline of the patch using chalk or pencil (do not use ink).
Cut the patch, cover the cut or puncture with approximately 2.5cm (1 inch) overlap on all sides.
3. Apply tape along the outline of the patch. This will prevent the glue
from spreading outside the patch area.
4. Apply glue on both the board and patch using a brush or other applicator. Make sure the glue is spread evenly and completely over the
board and patch. Let the glue dry for 5 minutes.4 5 6
HOW TO REPAIR A CUT OR PUNCTURE
IN YOUR INFLATABLE BOARD
SUPPLIES REQUIRED
•Glue (AQUASEAL® is recommended)
• Acetone or methyl ethyl ketone (M.E.K.)•Hairdryer
•Brush
•Tape
•Spatula or spoon
•Towel
(Not provided in the SUP board package)
1 2 3
Glue
M.E.K.

1824hAllow the glue to cure with
the board un-inflated for 24
hours prior to use.
HOW TO FIX A LEAKING VALVE
open
close
open
close
1. Inflate your board up to the max air pressure
2. Stick your valve wrench down inside of
valve and turn clockwise to tighten the
valve back down onto the board
1. Completely deflate your board 2. Undo the dust cap and insert the valve wrench into the valve and
twist counterclockwise to remove the valve
5. Apply the patch starting on one side and move towards the other side Be careful not to trap any air bubbles.
6. Use a hairdryer to gently heat the area to ensure a good bond between
the patch and the board.
Use a metal spatula or spoon and firm pressure to ensure a good bond
and to remove any air bubbles.
A. Try to tighten the valve
B. Re-install or replace a valve

19NOTE: Correctly use the wrench by pressing it with
one hand on top.
open
close
3. Check the rubber ring to make sure that it is in the correct position,
tight around the valve and there is no debris in the way
4. Be sure the pin spring is functioning properly and that there are no cracks along the edges
5. Ensure there are no strings from the drop stitching material6. Note the bottom piece of the valve is not attached to anything
7. Fit the valve back into your board
8. Align all the threads and twist to tighten9. Once the valve is hand tight, use the valve wrench to seal completely Rubber Ring

WARRANTY
AM warrants this product to be free from major defects in material or
workmanship to the original purchaser for a period of one (1) Year from the date of purchase. This warranty is subject to the following
limitations
1. The warranty is valid only when this product is used for normal recreational activities and does not cover products used in rental or school operations.
2. AM will make the final warranty determination, which may require inspection and/or photos of the equipment, which clearly show the defect(s). If necessary, this
information must be sent to the AM distributor in your country with prepaid
postage. Product can be returned only if a return authorization number is given in
advance by the AM distributor. The return authorization number must be clearly
labelled on the outside of the package, or it will be refused.
3. If a product is deemed to be defective by AM, the warranty covers the repair or
replacement of the defective product only. AM will not be responsible for any costs,
losses, or damages incurred as a result of loss or misuse of this product.
4. This warranty does not cover damage caused by misuse, abuse, neglect, normal wear and tear including, but not limited to punctures, damage due to excessive heat exposure, damage caused by improper handling and storage, damage caused by use in waves or shore break, board breakage caused by filling or crashing in surf
conditions, or damage caused by anything other than defects in material and
workmanship.
5. This product must not be modified and/or fitted with a motor except AM BlueDrive power fin.
6. This product must not be used in excess of the manufacturers recommended maximum load capacity.7. This warranty is void if any unauthorized repair, change or modification has been
made to any part of the equipment.
8. The warranty for any repaired or replacement equipment is good from the date of the original purchase only.
9. The original purchase receipt must accompany all warranty claims. The name of the retailer and date of purchase must be clear and legible.
10. There are no warranties that extend beyond the warranty specified here in.This product is designed in accordance with standards for a
specific use. Any modifications or transformations higher than
that indicated by the manufacturer could result in serious risks
for the user and will void the warranty.
WARNING
1
YEARYEAR