Aqua-Marina BLUEDRIVE X User manual

USERMANUAL
BLUEDRIVEX/X
PRO POWERFIN
PF-240X
PF-240XP
EN

SUP Boarding Kayaking Scuba-divingSnorkelling
CREATED FOR WATER LOVERS
WHO WANT IT ALL!
AM Official Site AM HOW -TO Guide AM Service Center List

CONTENTS
03
I Introduction ..............................................................................06
II
III Parts and Technical Specifications ........................................................ 07
IV
Product Details ...........................................................................06
BLUEDRIVE X /X PRO in Use .............................................................. 09
1. Summary
2. Preparing the BLUEDRIVE X /X PRO
3. Charging the BLUEDRIVE X battery with the battery charger
4. Charging the remote control
5. Charging the nose illuminating system
6. Remote control pairing
VUsing the BLUEDRIVE X /X PRO on SUP or Kayak ........................................ 16
1. Contents of BLUEDRIVE X /X PRO used on SUP or kayak
2. Assembling the BLUEDRIVE X /X PRO to SUP or kayak
3. How to use the remote control when BLUEDRIVE X /X PRO is used on SUP or kayak
IX
X
XI Warranty Terms
Battery Use & Care Information .......................................................... 28
Important Safety Precautions and Warnings ............................................. 30
VI Using the BLUEDRIVE X /X PRO for Snorkeling, Diving or Swimming ....................20
1. Contents of BLUEDRIVE X /X PRO used for snorkeling, diving or swimming
2. Assembling the handheld terminal
3. How to manipulate the BLUEDRIVE X / X PRO while snorkeling, diving or swimming
4. How to use the nose illuminating system
VII
Maintenance after Using BLUEDRIVE X /X PRO ......................................... 25
1. Cleaning
2. Troubleshooting
3. Storage
VIII Packing and Transportation of BLUEDRIVEX /X PRO
1. How to pack BLUEDRIVE X /X PRO in the carry bag
2. Travelling with BLUEDRIVE X /X PRO by air
................................... 27
.........................................................................33

Please read the instructions carefully before use and operate according to the
instructions.
•This product provides power for aquatic leisure products. It can only be used in water, not for other
purposes.
•This product can only be used in water. Do not allow the product to rotate in the air to avoid motor
burnout due to excessive heating.
•Minors under 14 years old should not use this equipment.
•Children aged 14 and under, people with physical, sensory, or other disabilities, or people lacking
experience and knowledge should not use this equipment without proper supervision or guidance
on the safe use of this equipment and understand the hazards involved.
•Cleaning and maintenance should not be done by children without supervision.
•The equipment must be fully charged and installed before use in the water.
•It is prohibited to use the electric fins after consuming alcohol or drugs.
•Before using this equipment, please check the product thoroughly to ensure that the remote
control, battery, propeller and other functions are normal.
•Please review the water conditions in the area you intent do use this equipment prior to entry.
Ensure that water conditions are appropriate for use and that the authorities of the area allow the
use of such equipment.
•Pay attention to the surrounding environment and avoid collision with ships or other swimmers.
•To ensure safety, a safety undershirt or life-saving equipment should be worn on site.
•Please take out the battery and store it properly according to the relevant regulations during
transportation or when carrying this equipment on aircraft.
•Do not put your fingers into the fins, and keep your clothes or other objects away from the
propeller.
•Avoid wearing loose clothes or equipment during use to prevent being caught in the propeller.
•For those with long hair, it is suggested to wear a swim cap to avoid getting caught in the
propeller.
•Check the battery power from time to time and return to shore before the power is exhausted.
•When using this product, please hold the handle tightly, and do not point the front and back of the
product at your own face or others.
•People who are not able to swim, snorkel, dive or perform other sports should not use this
product.
•When using this equipment in open water area, do not allow foreign objects such as clothing,
weeds, wire, fishing nets, shells, mud and sand to be sucked into the propeller to avoid danger.
The ambient temperature for using this product is 0°C (32°F) ~ 40°C (104°F), and the storage
ambient temperature is below 45°C (113°F).
•Do not use this equipment on the beach to prevent sand, shells or other foreign matters from
entering the propeller.
•Keep the equipment away from gasoline, rubber solution or other volatile or acidic substances.
•Keep the equipment away from sharp objects.
•Do not place heavy objects on the equipment.
•When using this equipment in dark waters or at night, sufficient lighting is required.
•It is prohibited to use this product to dive deeper than 10m.
04
SAFETYWARNINGS

05
•Do not use this equipment in sandy water or waters with similar physical properties.
•Do not use this equipment in case of any damage or malfunction.
•The product buoyancy is affected by the geographical location, temperature, depth, and water
flow, and may sink when the product is released.
•Remove the equipment out of the water when not in use.
•Before charging, take the rechargeable battery out of the equipment.
•If the equipment is to be stored for a long time, the battery should be taken out and the power
terminals should not be short-circuited.
•The remote control and headlamp lighting system include a non-replaceable polymer lithium
battery.
•When charging the battery, the ambient temperature range should be 10°C (50°F) ~45°C (113°F).
The storage ambient temperature should be below 45°C (113°F).
•Connect the positive and negative poles of the battery correctly, reverse charging is strictly
prohibited. If the positive and negative poles of the battery are connected inversely, the battery
will not be charged. In addition, reverse charging will reduce the charging and discharging
performance and safety of the battery, and will lead to heating and leakage.
•The charging current should not exceed the maximum charging current specified in this manual. If
the charging current is greater than the recommended value, the charging and usage
performance, mechanical performance and safety performance of the battery may have problems,
which may lead to heating or leakage. The charging voltage shall not exceed the rated voltage of
DC 25.2V specified in this manual, and DC 25.5V is the maximum charging voltage. When the cell
voltage is higher than the rated voltage, it may cause problems in the charging and usage
performance, mechanical performance and safety performance of the battery, and may cause
heating or leakage.
•The battery storage voltage is 22.2V~23.1V. Storage while fully charged is not suggested.
•Do not directly connect terminals with metal objects. This will short-circuit the battery, causing
heating and discharging.
•Only the charger designed for lithium polymer/lithium-ion battery can be used. Do not use NIMH/
NICD/ LIFEPO4/ lead-acid charger. If the charger can support different battery types, be sure to
select the lithium polymer (Lipo) mode on the charger. Otherwise, it may cause fire, resulting in
personal injury and property loss.
•Always charge the battery in an open area away from flammable materials, liquids and surfaces.
•Do not charge the battery if it is very hot (above 37.8°C /100°F). Do not charge the battery until it
has cooled down.
•Do not replace the battery under water. When replacing the battery, make sure to do it in a dry
environment and keep the equipment and hands dry.
•The battery cannot be disassembled, modified, or subjected to strong vibration or impact. Please
handle the battery carefully after installation.
•The battery should not be allowed to get damp and the battery metal socket should not come in
contact with liquids. When you assemble, disassemble and store the battery, please keep the
product and your hands completely dry, and operate in a dry environment.
•If the battery produces abnormal smell, heat, discoloration, deformation or other abnormalities
during use or charging, please stop using or charging immediately. If the above abnormal
conditions occur during the storage of the battery, please inspect the storage environment.
•Do not throw the battery into fire.
•Do not put the battery into a microwave oven, high-pressure vessel, or electromagnetic oven.
•Do not store the battery in an outdoor vehicle or at high temperatures for long periods of time.
•This product should be stored away from direct sunlight. High temperatures will damage the
battery, causing explosion or leakage. Do not repair this equipment without authorization to avoid
leakage, damage, fire, or electric shock.

06
I. INTRODUCTION
Introducing the new BLUEDRIVE X, our most innovative underwater propulsion
system. Highly intelligent and equipped for a multitude of adventures, this all-in-one
kit opens the doors to endless possibility in the water.
Created for water lovers who want it all. The BLUEDRIVE X is ready to be your SUP,
kayaking, swimming, snorkelling, diving and more companion.
You name your water activity and the BLUEDRIVE X is ready for action.
II. PRODUCTDETAILS
LED
Headlamp
Main Unit Motor
Propeller
Auxiliary Rail
Water Inlet Quick Release
Cylinder Mesh Screw
Tail Cylinder
Headlamp Key Switch

07
III. PARTSAND TECHNICAL SPECIFICATIONS
3.1 PART LIST
12
3 5 6 7
89
14 15
21
4
16 13
10
11 12
19 20
17 18
1 Main unit x 1
2Headlamp x 1
3 Left handle top cover x 1
4Handle bracket x 1
5 Quick-release spare screw x 2
6Remote control x 1
7 Remote control base x 1
8Right handle x 1
9 Left handle x 1
10
Battery (PF-240X x 1,PF-240XP x 2)
11
SUP connector x 1
12
Locating pin x 2
13
Charger x 1
14
USB data cable x 2
15
Watch strap x 1
16
Safety rope x 1
17
Battery compartment waterproof backup ring x 1
18
Top cover waterproof backup ring x 1
19
Manual x 1
20
Warranty card x 1
21
Portable bag x 1

Note:
1. With the consumption of battery power, the power will gradually weaken, and the equipment will
automatically slow down and jump to a lower gear, or the high and middle gear will not be available.
This is within the normal application.
2. This data is for reference only. The specific use duration will vary with different gears, user weights,
use environments, and use frequencies.
3. The camera base of this product only supports some models of action cameras, which are not
included with this product.
4. The SUP connector of this product only supports some types of SUP boards, which are not included
with this pruduct. If necessary, please purchase an adaptive SUP fin box adaptor.
08
3.2 TECHNICAL SPECIFICATIONS
Main Unit
Product Model PF-240X PF-240XP
Weight 3.5 kg / 7.7 lbs 4.3 kg / 9.5 lbs
Dimension 432 x367 x170 mm 515.5 x 367 x170 mm
Waterproof Depth 10m /3h 10m /3h
Adjustable
Gear
Speed (km/h) Duration (min) Speed (km/h)
Duration
(min)
350 3100
535 570
720 740
Capacity
Thrust Max. 7 kgf Max. 7 kgf
External Devices
Supported Support attaching sports cameras
Battery
Model LB-24V6
Charging Voltage 25.2 V
Charging Current 3.3 A (Max 4.4 A)
Rated Capacity 4400 mAh
Rated Energy 97.68 Wh (PF-240X*1,PF-240XP*2)
Charger Model: GJS150-2520330
Charging Duration About 2.5 h
Weight 630 g / 22.2 oz
Charger
Input Voltage AC 100 ~240 V
Output Voltage DC 25.2 V
Output Current 3.3 A (Max 4.4 A)
Headlamp
Rated Voltage DC 3.7 V
Rated Capacity 1000 mAh
Charging Voltage DC 5V 1A
Charging Duration About 4.5 h
Energy Consumption
High-intensity Lighting About 2 h
Energy-saving Mode About 8 h
High-brightness Flickering About 4 h
SOS Mode About 5 h
Lighting Distance 3m
Remote
Control
Model RC-23BX
Rated Voltage DC 3.7 V
Rated Capacity 450 mAh
Charging Voltage DC 5V 1A
Charging Duration About 1 h
Energy Consumption About 5 h
Charging Cable USB magnetic data cable, 2-pin spacing: 4mm

09
IV. BLUEDRIVEX/X PROIN USE
4.1 SUMMARY
This section applies to the proper use of BLUEDRIVE X/ X PRO. Please follow each of the steps
carefully in order to start your BLUEDRIVE X/ X PRO.
Once the device is set up, go to the relevant section with your activity as follows:
For the use on a SUP or kayak, go to section V.
For the use while snorkeling, diving or swimming, go to section VI.

Step 3:
First, turn the “▲”on the battery lock cover to “OPEN”, which makes a “click” sound.
Then, align the latch on the battery plug cover with the slot on the battery.
Finally, turn the “▲” on the battery lock cover clockwise to “LOCK”, which makes a “click” sound.
(When turning anticlockwise to “OPEN”, the lock cover will be unlocked.)
10
4.2 PREPARING THE BLUEDRIVE X /X PRO
Step 1:
Open the battery compartment cover, remove the battery plug cover.
Step 2:
Install the battery into the battery compartment.
Install the lower battery upside down by pulling up the handle at the bottom of the battery, direct
the battery socket towards the bottom of the battery compartment, and then return the handle to a
flattened state. Install the upper battery upright, with the battery socket towards the top of the
battery compartment.
OPEN LOCK
Battery
Compartment
Cover
Battery x 2
Battery
Handle

Battery
Compartment
Cover
Main Unit
Step 4:
First, inspect whether the waterproof ring 1 on the battery compartment cover is installed properly.
Align the four concave clips of the battery compartment cover with the convex clips of the main unit,
and then rotate clockwise to lock. When the “▲” of the battery compartment cover aligns with the
“” of the main unit and makes a “click” sound, it means that the battery compartment cover is
locked. (Rotate the battery compartment cover anticlockwise, when the battery compartment cover
“▲”is aligned with the main unit “”, it means that it is unlocked.)
Battery Plug
Cover
O PEN LO C K
Step 5:
First, inspect whether the waterproof ring 2 on the main unit is installed properly.
Then, rotate the headlamp clockwise and tighten it in place. When the “▲” of the headlamp
housing is aligned with the “ ” of the main unit, it is locked. (Rotate the headlamp anticlockwise,
and “ ”represents the unlocking direction.)
Headlamp
Waterproof Ring 2
Align the
concave clips
of the battery
compartment
cover with the
convex.
11
O PEN
LOCK
Waterproof Ring 1

12
Step 2: Connect the plug (a) of the battery charger to the AC power supply (AC100V-240V,
50/60Hz; if necessary, use the power adapter).
Step 3: The red indicator of the charger indicates that the battery is being charged, and the green
indicator indicates that the battery is fully charged. It takes about 2.5h to fully charge the battery.
Note: Please unplug the battery charger when not charging.
3. Charging the BLUEDRIVE X battery with the battery charger
Warning:
1.Be sure to fully charge the battery before the first use.
2. Before removing the battery from the main unit, please turn off the machine
with the remote control first to ensure the product is stopped.
Step 1: First, turn the “▲” on the battery lock cover to “OPEN”, which makes a “click” sound.
Then, align the pin at one end of the battery charger with the battery slot and insert it downward.
Finally, turn the “▲” on the battery lock cover clockwise to “LOCK”, which makes a “click” sound.
a
Red Light -- Charging
Green Light -- Fully Charged

13
Note:
Do not scratch the charging terminal with sharp objects, this will affect the service life of the
product.
Keep the surface of the charging terminal dry.
4. Charging the remote control
Warning:
1. Before charging, please confirm that the remote control is off.
2.Do not operate the remote control while charging.
Step 1: Remove the silicone cover of the charging interface at the bottom of the remote control in
the direction of the arrow.
Step 2: Please use DC 5V 1A power adapter (not provided) or standard USB charger for charging.
Connect the magnetic connector (a) of the USB data cable to the remote control, and the other end
(b) to the USB charging port.
Step 3: If the red indicator of the remote control is on, it means that the battery is charging. If the
green indicator is on, the battery is fully charged and the connection should be disconnected.
Step 4: After charging, please cover the silicone cover of the charging interface at the bottom of the
remote control.
Red Light -- Charging
Green Light -- Fully Charged
Silicone Cover
a
b

Green Light Flashing -- Charging
Green Light On -- Fully Charged
5. Charging the nose illuminating system
Warning:
1. Before charging, make sure that the headlamp is off.
2.Do not operate the headlamp while charging.
Step 1: Rotate the headlamp anticlockwise and remove it from the main unit.
Step 2: Please use DC 5V 1A power adapter (not provided) or standard USB charger for charging.
Connect the magnetic connector of the USB data cable to the headlamp, and insert the other end
into the USB charging port.
14
Step 3: If the charging indicator is green and flashing, it means that the battery is charging; if the
indicator stays solid green, it means that the battery is fully charged and should be disconnected.
Note:
Do not scratch the charging terminal with sharp objects, this will affect the service life of the
product.
Keep the surface of the charging terminal dry.

15
Remote Control Interface Description
After pairing, please note that:
If you still need one-to-one control after replacing the battery, please pair again. If it is not necessary,
please restore the remote control to the default pairing (only required for the first time) by following
the instructions below.
Restore default pairing:
If you want to control multiple units with one remote control, you can restore the default pairing state
to realize such operation.
1) Remote control: After startup, simultaneously press the ON/OFF “” button and the gear-down
“−”button until the red indicator light of the remote control power flashes, the remote control will
restore its default pairing state.
2) Main unit: Take out the battery of main unit, wait for 5s, and then reinstall it. The main unit will
restore its default pairing state.
The remote control in the default state can control one or more main units in default state nearby.
4.6 Remote control pairing
When there are multiple PF-240X (P) units nearby, to avoid mutual interference, one-to-one control
can be realized through pairing operation.
Step 1: Remove the battery of the main unit.
Step 2: Press the ON/OFF “ ”button on the remote control to start, press the ON/OFF “ ” button
and the “+” gear-up button simultaneously (about 3s) until the green indicator light on the remote
control and the main unit power indicator light flash, and then release the buttons. The remote
control will enter pairing mode.
Step 3: Install the battery of the main unit, and the system will pair automatically.
Step 4: After the screen of the remote control flashes quickly (5 times), the pairing is successful, and
the remote control resumes displaying the power and enters normal mode. If the full screen still does
not flash after 3 min, the pairing failed. Please restart pairing from Step 1.
Main Unit Power
Indicator
Remote Control
Power Indicator
“+”
Gear-up Key
Gear Indicator
“-”
Gear-down Key
“ ”
ON/OFF Button

16
V. USINGTHEBLUEDRIVEX/X
PRO ON SUPOR KAYAK

Rail of Main Unit
5.2 Assembling the BLUEDRIVE X /X PRO to SUP or kayak
Step 1: Align the rail A of the fin box connector with the auxiliary rail of the main unit, and slide the
connector onto the main unit along the rail.
Rail B
Sup Fin Box Connector
Rail A
5.1 Contents of BLUEDRIVE X /X PRO used on SUP or Kayak
17
Step 2: Take one locating pin, align with hole A, and insert for locking.
12
4
3
6 7 5
1
Main unit x 1
2
Headlamp x 1
3
Battery (PF-240X x 1,PF-240XP x 2)
4
Remote control x 1
5
Watch strap x 1
6
Fin box connector x 1
7
Locating pins x 2
Locating Pin
Hole A

18
Step 3: Align the fin box connector rail B with the fin box on SUP/KAYAK (not provided), slide the
connector onto the fin box along the rail, and then insert the locating pin to hole B for locking.
Fin Box
Connector
Rail B
Fin Box Hole B
Note:
If your SUP fin box has a “Swift Attach Fin System (SAFS)”, install the fin box adaptor (*sold
separately) as follows: Install the SUP fin box connector onto the adaptor by sliding it into
adaptor rail C, and then insert the locating pin to hole B for locking.
Sup Fin Box Adaptor
(*Sold Separately)
Rail C
Rail B
Hole B
SAFS Fin Box
Adaptor
Locating Shaft
SAFS Fin Box

5.3 How to use the remote control when BLUEDRIVE X /X PRO
is used on SUP or kayak
Step 1: Attach the remote control to the silicone watch strap.
Remote Control
Watch Strap
There are 3 gears, and the
LED white light is always
on according to the speed.
Remote control power indicator (green
light always on)
Low Battery Indicator: If the red light is on
during operation, it means the battery is
running out of power.
Main unit power indicator (white light
always on)
When the power is lower than 10%,
the white light flashes. If flicker occurs
during operation, it means the main
unit battery is running out of power.
Step 3: Press the acceleration key “+”on the side of the remote control, and the display will show
“”, and the unit will run at the default low speed. Press “+”to accelerate gear, and press “−”to
decelerate gear.
Step 4: To turn off the power, press the ON/OFF button “ ” on the remote control.
Note:
With the consumption of battery power, the power will gradually weaken, and the equipment will
automatically slow down and jump to a lower gear, or the high and middle gears will not be
available. This is within the normal operation.
The maximum control distance of the remote control is 3m under the SUP or kayak mode. The main
unit and remote control will automatically power off if there is no operation for 15 minutes.
19
Step 2: Press the ON/OFF button “”, and the remote control display will display the remote control
power and the main unit power, indicating that the unit has started successfully.
“ ”
ON/OFF Button

1 Main unit x 1
2 Headlamp x 1
3 Left handle top cover x 1
4 Handle bracket x1
5 Quick-release spare screws x 2
6 Remote control x 1
7 Remote control base x 1
8 Right handle x 1
9 Left handle x 1
10
Battery
(PF-240X x 1,PF-240XP x 2)
11
Safety rope x1
VI. USINGTHEBLUEDRIVEX/X PROFOR
SNORKELING,DIVINGOR SWIMMING
20
6.1 Contents of BLUEDRIVE X /X PRO used for snorkeling,
diving or swimming
12
3 5 6 7
89
4
11
10
Other manuals for BLUEDRIVE X
1
This manual suits for next models
3
Table of contents
Other Aqua-Marina Sport & Outdoor manuals

Aqua-Marina
Aqua-Marina BT-21BRP User manual

Aqua-Marina
Aqua-Marina CN-ORP User manual

Aqua-Marina
Aqua-Marina ISLAND BT-I250 User manual

Aqua-Marina
Aqua-Marina AM-20NU User manual

Aqua-Marina
Aqua-Marina Breeze User manual

Aqua-Marina
Aqua-Marina Breeze User manual

Aqua-Marina
Aqua-Marina Pure Air User manual
Popular Sport & Outdoor manuals by other brands

Heater Sports
Heater Sports HeaterPro HTR499CM110V instructions

Levenhuk LabZZ
Levenhuk LabZZ SK20 user manual

Promatic
Promatic Signature Skeet operating instructions

SPORTNOW
SPORTNOW A62-034V00 Assembly instruction

Jula
Jula 951-011 operating instructions

Spice & Soul
Spice & Soul 377085-2110 Instructions for use