Aqua One Windsor 88 User manual

O(a)
M
Base x 1
Top of Cabinet
L
Windsor 88
Assembly instructions
Ex2
Fx16
T
Centre Panel
x 1
Left door x 1 Right door x 1
R S
Ax10 Bx10 Cx12
Hx4
Tools required:
Zx8
Contents:
Parts Required
Glass tray x 1
Step 6: Hood W, aquarium U and cabinet
Place aquarium Uon top of
cupboard by lifting it on from
the back and sliding it forward.
VERY IMPORTANT: DO NOT REMOVE THE
POLYSTYRENE ATTACHED TO THE BOTTOM
OF THE AQUARIUM!
Install Filter (see filter instructions for details)
Install Heater (see heater instructions for details)
Put glass tray Von top of aquarium.
Install reflector lighting (see lighting instructions
for details)
Slide hood Wonto aquarium. Insert maintenance
lid Xinto the hood.
®
Aqua One and Kong’s are registered trademarks. www.aquaone.com.au.
©
Aqua One 2005
Precision Manufactured in the P.R.C.
Designed in Australia by Aqua One
Distributed in Australia by:
Kong's (Aust.) Pty. Limited
48 Williamson Rd. Ingleburn.
2565 NSW Australia.
Distributed in New Zealand by:
Kong's (NZ) Limited
52 Glenlyon Avenue.
Greerton. Tauranga New Zealand.
Distributed in the UK by:
Kong’s (UK) Ltd.
C/O Aqua Pacific UK Ltd.
PO Box 268
Romsey Hampshire
S051 0WW
United Kingdom
Important Notice
It is absolutely imperative that you ensure this cabinet and aquarium is installed upon level flooring. It is also a prerequisite that
you ensure the flooring upon which it is positioned is able to support the weight of this aquarium which could be up to 600kg
including water and decorations.
Installation upon uneven flooring will result in poor distribution of weight. Damages to the aquarium, cabinet or equipment and
damages caused by leaks due to improper or uneven installation are not covered by the guarantee with this product.
Care and Maintenance of your Aqua One Aquarium
Glass: It is recommended that you use a good quality glass cleaner and a non abrasive lint free cloth. Glass cleaner should only
be used on the outside of the aquarium.
To clean the glass on the inside of the aquarium, it is recommended that you use an Aqua One Scraper or Magnetic Cleaner
(available from your local Aqua One dealer).
Cabinet and Hood: The use of a damp cloth is recommended, do not use any detergents or harsh chemicals to clean the cabinet
and hood as damage may occur.
U
cover
hood
light
glass tray
heater
canister
filter
Glass Aquarium x 1
U
Shelves x 2
N N
W
X
Y
Hood Insert x 1
X
Hood x 1
W
Y
Cover x 1
V
QP
Left side x 1 Right side x 1
Back
Panel
x 1
Back
Panel
x 1
O(b)
Instruction version:- 22/02/2008

M
O(a)
P Q
M
P Q
T
O(b)O(a)
N
L
M
M
A
Attach doors to cabinet
using screws F and
the predrilled holes
Insert shelves using
pins Z
Step 1: Base M and 10 x A
Back Panel O(a), O(b), Centre Panel T. Parts 6 x B
Step 2: Lower the Back Panels O(a), O(b) and Centre Panel T onto the Base
Step 3: Lower the Side Panels P & Q onto the Base
Step 4: Cabinet lid L and 10 x C
Position cabinet lid on the cabinet
construction, open side pointing
upwards. Line up screws C with
holes and fasten, ensuring screw
heads do not stand proud.
Step 5: Door panels R, S, 4 x H, 16 x F
Fasten hinges H to door
panels using screws F
R S
H H
E
Attach door handles
M
O (b)
O (a)
QP
B
B
C
T
O(a)
M
O(a)
P Q