Aqua Phase AQ-F250 User manual

Medical Equipment Washer
Operating Manual
AQ-F250
Your Aqua Phase Includes the Following Options:
READ ALL MATERIAL PRIOR TO OPERATION
 Disinfectant Application System
 Utility Wash Trays
 Front Safety Window
 Lighted Wash Chamber
 Pressure Sensor
Digital Temperature Display
 Wheel Rotation System
 Multi-size Wheel Rotator
 Other __________________
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

Table of Contents
Operation Information
Caution & Notices ...........................................................................................1
General Information..................................................................................... 2-6
Basic Set-up Procedures.............................................................................. 7-8
Fill & Drain Line Information................................................................... 9-11
Controller Information ..................................................................................12
Operating Procedures & Wash Sequence......................................................13
Disinfectant Application System (option) ....................................................14
Daily Operating Procedures...........................................................................15
Daily Operations Log ...................................................................................16
Weekly, Monthly, Annual Procedures .........................................................17
Periodic Operations Log ...............................................................................18
De-liming Instructions............................................................................. 19-21
Aqua Phase Limited Warranty ......................................................................22
Trouble Shooting Guide........................................................................................23
Aqua Phase Will Not Start.............................................................................24
Aqua Phase Will Not Fill With Water...........................................................25
Aqua Phase Will Not Stop Draining / Draining Takes Too Long ................26
Aqua Phase Will Not Stop Filling / Error Message: Fill Time Expired .......27
Items Washed Have Water Spots or Cloudy Film .......................................28
Items Not Cleaned Properly ..........................................................................29
Growling Noise Pump / Low Spray Volume ...............................................30
Low Pressure Indicator Light / Message Always On ...................................31
Using Too Much Cleaning Solution or Rinse Agent ...................................32
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

Table of Contents
Technical Data Information Sheets
Control Panel Controls & Electrical Layout .....................................................
Fuses ..................................................................................................................
Wire Diagrams...................................................................................................
Domestic Parts Listing.......................................................................................
Typical Chemical Pump Assembly...................................................................
Valve Inspection Procedures.............................................................................
½” Valve (Fill & Disinfect) ..............................................................................
Disinfectant Mixing Valve ...............................................................................
Wheel Brush Adjustment...................................................................................
Technical Data Single-Stage Injector................................................................
Pump Impeller Inspection Procedures...............................................................
Main System Pump............................................................................................
Drain Pump........................................................................................................
Aqua Phase Chemicals & Descriptions
Aqua Phase Chemicals Material Safety Data Sheets
AQ-240 Cleaning Solution................................................................................
AQ-260 Rinse Solution .....................................................................................
AQ-280 Rust Inhibitor.......................................................................................
AQ-725 De-liming Solution..............................................................................
AQ-HD128 Neutral Disinfectant.......................................................................
AQ-PD130 Germicidal Disinfectant .................................................................
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

DO:
DO:
DO:
Read this operations manual and follow all instructions.
Call your dealer, sales representative, or the factory with any questions,
need for more information, or to order supplies for your Aqua Phase
Washer.
Wear Personal Protective Clothing
DO NOT: Operate the machine without all the filter screens in place.
DO NOT: Climb into the Wash Chamber.
DO NOT: Wash any item with unsealed electrical components. Unless IP 65 rated
or higher.
DO NOT: Perform any type of service operation unless the machine is unplugged.
DO NOT: Use an extension cord between the wall outlet and the machine.
DO NOT: Try to modify the machine in any manner without factory approval.
DO NOT: Operate the machine in high foot traffic areas.
DO NOT: Use garden hoses for the fill and drain hoses.
DO NOT: Operate the machine unless you have been properly trained to do so.
Aqua Phase carries a complete line of supplies and parts and a variety of
cleaning, rinse, and disinfectant solutions specifically formulated and chosen
to work with your Aqua Phase machine.
Order your solutions, supplies, or parts by calling your dealer or Aqua
Phase at 800-208-9274 or 715-463-5851.
CAUTION & NOTICES
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

GENERAL INFORMATION
Front View Rear View
Control Panel Chemical Cabinet
Locking Handle
Mechanical Cabinet
Locking Latches for
Mechanical Cabinet
Fill & Drain Connections:
(not shown)-located on side of
Aqua Phase
•Control Panel with LED Cycle Display
•Front Door Safety Switch
•Fixed 1” PVC Spray Arms with adjustable
nozzles
Optional Disinfectant Application System
(not shown) Includes:
•Disinfectant Spray Header
•Feed Lines (4) to Disinfectant Spray Nozzles
Inside Wash Chamber View
Standard Components Includes:
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

GENERAL INFORMATION
CONTROL PANEL SWITCHES &
FUNCTIONS
Switch Options/Function
“STOP” Button When pressed, will stop all Aqua Phase wash functions
“START” Button Must be pressed to start any Aqua Phase wash function
Allows you to select the length of wash:
WASH TIME Selector Switch
“3 MIN” = Three minute wash cycle
“5 MIN” = Five minute wash cycle
“7 MIN” = Seven minute wash cycle
“RUN/DRAIN” Selector Switch “RUN”: Set to “RUN” to wash an item.
“DRAIN”: Set to “DRAIN” to drain the water in the machine.
*WASH MODE Selector Switch
The water should be drained when you are done washing for
the day or if you relocate the machine. In order for the
“DRAIN” function to work, the Wash Mode switch must be
set to “CLEAN & DISINFECT” or “CLEAN ONLY”.
CLEAN & DISINFECT: When this mode is selected, Aqua
Phase will perform a complete wash and rinse for the time
specified on the WASH TIME Selector Switch. It will then
automatically apply disinfectant solution
CLEAN ONLY: When this mode is selected, Aqua Phase
will perform a complete wash and rinse cycle for the length
of time specified on the WASH TIME Selector Switch. It
will not apply disinfectant.
DISINFECT ONLY: When this mode is selected, Aqua Phase
will apply disinfectant solution only. It will not wash or
rinse.
*Wash Mode selection is part of the
Disinfectant Application System
option if purchased.
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

GENERAL INFORMATION
MECHANICAL COMPONENTS
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

GENERAL INFORMATION
FILTERS & SCREENS
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

GENERAL INFORMATION
RECOMMENDATIONS &
REQUIREMENTS
Recommendations:
•Water Temperature:The Aqua Phase System will perform best with a hot water supply between
115°- 130°F (46°-55°C). If the supplied water temperature is below 105°F (40°C) water spotting or
afilm may occur on the equipment.
•Cleaning Solutions:Aqua Phase AQ-240 Cleaning Solution and Aqua Phase AQ-260 Rinse Agent
are recommended for use in the unit.
•Disinfectants: Use a concentrated disinfectant with a dilution rate of 1 ounce per gallon
(1:128). AQ-128 Neutral Disinfectant or AQ-130 Germicidal Disinfectantare recommended.
Disinfectants with other dilution rates can be used, however, the dilution setting of the Aqua Phase
unit must bemodified. This is not difficult—see Technical DataInformation Sheet for the
Disinfectant Mixing Valve. Do NOT use Hydrogen Peroxide based disinfectants as these are
damaging to the aluminum used on some medical equipment.
•Plumbing Connections: Use the hoses provided with Aqua Phase for theFill andDrain connections
rather than rigid piping. (See Fill and Drain Line Set up pages in this Operator Manual.) This will
make access to the Chemical Cabinet and Mechanical Cabinet much easier if service isneeded and
will allow for periodic cleaning of the floor under theAqua Phase unit.
Requirements
•Electrical: Aqua Phase requires a 120 volt, 20 ampere electrical circuit. This circuit should be
dedicated for Aqua Phase use only.
•Water Volume: Aqua Phase requires approximately 5.5 gallons of hot water per cycle. See
Operating Procedures and Wash Sequence page for details.
•Water Pressure:Aqua Phase requires a minimum of 35 PSI (Pounds per Square Inch) (2.42 Bar of
water pressure.
•Cleaning Solutions: The use of Aqua Phase brand solutions is required for the Aqua Phase
warranty to remain intact unless the use of other solutions have been approved, in advance, by the
Aqua Phase factory. See Warranty Pagefor details.
•Plumbing Drain Hose: The discharge end of the Drain Hose must be secured at least 18”above
floor level. (See Fill and Drain Line Set up pages in this Operator Manual.)
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

BASIC SET-UP PROCEDURES
Aqua Phase, A Division Mid-State Stainless Inc. ● 330 W. Benson Ave. ● PO Box 228 ● Grantsburg, WI 54840 ● USA
800-208-9274 ● 715-463-5851 ● FAX: [phone] ● Email: [email protected] ● WEB: www.aqua-phase.com
If Aqua Phase has been transported during freezing weather, allow the Aqua Phase to warm for
4-6 hours before running.
1. Read all Aqua Phase instructions and operations material
2. Remove Aqua Phase from pallet
3. Move Aqua Phase to location of operation. Ensure that Aqua Phase is level
4. Remove items packed inside the Wash Chamber for shipping (hoses, optional racks, trays,
and chemical solutions will often be packed inside the Wash Chamber).
5. Connect the Fill Hose using supplied hose.
•DO NOT USE A GARDEN HOSE.
•Only use hoses rated for 150° F or higher for both fill and drain connections.
6. Connect the drain hose.
•The drain end of the hose MUST BE HIGHER than the drain hose connection on
the washer. See Fill and Drain Line page for information.
•Drain hose must be securely fastened to the drain.
7. Once the Fill and Drain connections are secure, slowly turn on your hot water supply and
inspect for loose connections.
8. For standard 120-volt operation, connect Aqua Phase to a standard 20 AMP electrical service
•Press the reset button located on the Ground Fault Circuit Interrupter (GFCI) in the
power cord.
•DO NOT use a power extension cord between the wall outlet and the Aqua Phase
9. With Special Ordered 240-volt configuration, the end user must make the final
connections and provide the appropriate cord plug with Ground Fault Circuit Interrupter
(GFCI) reset button.
•Due to the variety of receptacle and connection types as well as local codes and
regulations, all electrical connections should be performed by a qualified electrician in
accordance with local codes and regulations.
(Continued next page)
Electrical line inlet
Electrical connection J-box
inside Mechanical Cabinet

Warning:
Wear Protective Clothing When Working With Any Chemicals.
Warning:
Consult the material safety data sheets located in the
back of this manual and your company’s
hazardous substance policy before handling any chemicals.
Key to Aqua Phase chemical solution hoses:
•The RED hose is for detergent.
•The BLUE hose is for rinse-aid.
•The CLEAR hose is for disinfectant, if installed.
NOTE: The disinfection injection rate is preset at the factory for use of a disinfectant that requires a
dilution rate of 1 oz. per gallon of water. Contact the factory if adjustment of the injection rate is
necessary.
3. On the control panel at the front of the machine:
Set the "WASH TIME" switch to "3 MIN".
Set the “RUN/DRAIN” switch to “RUN”.
Set the wash mode switch to "CLEAN & DISINFECT" or "CLEAN ONLY" if no disinfectant
application system is installed.
4. Close the front door.
5. Press the “START” button. The “START” button is located on the control panel at the front of the
machine.
•Allow Aqua Phase to run a two complete cycles before washing any items.
If Aqua Phase does not start, see the "TROUBLESHOOTING: Will not start” section of this manual or
call the factory for support.
BASIC SET-UP PROCEDURES
(continued)
1. Place Chemical Solutions in the Chemical Tray (located inside the Chemical Cabinet at the rear of the
Aqua Phase) as the locations marked "DETERGENT" and "RINSE-AID".
2. Remove chemical bottle caps and place the appropriate colored hoses in bottle openings RED hose for
Detergent/ BLUE hose for Rinse-Aid.
•Do not dilute the Detergent or Rinse-Aid solutions.
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

9
FILL & DRAIN LINES
HOSES
•The Aqua Phase Washer System has female, garden hose style connectors.
•One hose is for filling the washer (Fill Line) and is connected to your water supply .
•One hose is for draining the washer (Drain Line).
FILL LINE CONNECTION
•The Aqua Phase System is designed with a built-in Fill Line Air-Gap.
•See “Fill Line Options” diagram page for Water Supply options/methods.
DRAIN LINE CONNECTION
•The Aqua Phase System should be drained according to local plumbing codes.
oTHE END OF THE DRAIN HOSE MUST BE HIGHER THAN THE DRAIN
CONNECTION TO AQUA PHASE SYSTEM.
oIf the Drain Hose is run directly to a floor drain, water will siphon out of the Aqua
Phase during operation.
•Typically, the Drain Hose will run to a stand pipe or utility sink (similar to a home washing
machine set-up). Use of standpipe is recommended. See “Drain Line Options” diagram
page. Please check with your local building codes for stand-pipe requirements. A standpipe
should be a minimum of 2” diameter with a minimum height of 32”.
•The drain hose must be secured at the drain to prevent a whipping action.
A SET OF (2) 10’ LONG HOT-WATER RATED HOSES ARE INCLUDED WITH
THE AQUA PHASE WASHER SYSTEM.
If needed, 25’ hot-water rated hoses are available from Aqua Phase at additional cost.
PLEASE CALL AQUA PHASE TECHNICAL SERVICE AT 1-800-208-9274 WITH ANY QUESTIONS
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

FILL LINE OPTIONS
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-28-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

Aqua Phase, A Division of Mid-State Stainless, Inc. 330 W. Benson Ave. PO Box 228Grantsburg, WI 54840 USA
800-208-9274 715-463-5851 FAX: [phone] Email: [e-mail] Web: www.aqua-phase.com
DRAIN LINE OPTIONS

CONTROLLER INFORMATION
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com
Message One Run mode selected.
•Doors closed.
•Ready to start.
Message Two Drain mode selected.
•Doors closed.
•Ready to start.
Message Three Machine filling for wash cycle
•Run mode selected.
•Doors closed.
•"Start" button pushed.
Message Four Machine is in Wash Cycle.
•Machine done filling for wash
cycle.
•Detergent solution
automatically injected.
•Wash cycle will run for time
selected (3,5, or 7 minutes)
Message Five
•Wash water is being drained
OR
•Drain mode selected and
"Start" button pushed.
Machine done with wash cycle. Machine beginning Rinse cycle.
•Wash cycle complete
•Wash water drained
•Machine is filling with fresh
water for Rinse cycle.
Message Seven Message Eight
Message Nine
Disinfectant Application System Running (Option)
•Fresh water mixed with
disinfectant solution.
•Item in Wash Chamber sprayed
with solution.
1. Clean & Disinfect Selected
before wash cycle started.
Wash & Rinse cycle done.
2. Disinfect Only selected &
"Start" button pushed.
Message Ten
Machine is in rinse cycle.
•Machine done filling for ---
rinse cycle.
•Rinse solution
automatically injected.
•Rinse cycle approximately
1.5 minutes.
Machine completed selected operation.
Front door of Wash Chamber
must be opened before next
operation can begin.
**After Wash Cycle, prior to
draining of wash water.**
Message Six
Check Low Level Float
•Item removed/loaded.
•Wash Chamber inspected
for debris.
•Safety switches operational.
•Is float is free of debris?
•Is float is operating properly?
•Call technical support if this
does not solve problem

OPERATING PROCEDURES &
WASH SEQUENCE
OPERATING PROCEDURES
1. The current status of the Aqua Phase system ("Wash cycle", "Rinse cycle", "Cycle complete", etc.) will be
shown on the LCD display of the control panel.
2. After pressing the "START" button, the computer will check to see if there is water in the water reservoir.
If the reservoir is not full of water, Aqua Phase will automatically fill to the appropriate level. The
reservoir holds approximately 5.5 gallons.
3. When the reservoir is full, the pump will start and begin the wash cycle, spraying the item being washed.
AQ-240 Cleaning Solution is automatically injected shortly after the wash cycle begins.
4. The Aqua Phase will now be in the wash phase, and will continue for the wash time selected of 3, 5, or 7
minutes.
5. When the wash phase is complete, the dirty wash water will be pumped out of the Aqua Phase to the drain.
6. Aqua Phase will automatically refill to the appropriate level with fresh water.
7. After the reservoir is filled with water, the pump will start and the Aqua Phase will begin the rinse phase.
The AQ-260 Rinse Agent is automatically injected shortly after the rinse phase begins. The rinse cycle
will last for approximately 90 seconds.
8. If you have the Disinfectant Application System, the cycle will automatically begin if CLEAN &
DISINFECT was selected.
TO DRAIN THE MACHINE MANUALLY
During normal automatic operation, the rinse water remains in the machine and will be the wash water for
the next item placed in the chamber. If you choose, you may drain the rinse water prior to beginning the next
wash cycle.
1. Load the item to be washed into wash chamber and close the front door.
For Aqua Phase units equipped with the Wheelchair Wheel Rotation System:
a. For washing wheelchairs - position the front, small diameter wheels into the Wheel Carriage
loading rack, tip the wheelchair forward, and slide it into the wash chamber until the rear, large
diameter wheels rest between the two drive bars closest to the door.
b. For washing items other than wheelchairs - it is recommended that you use the Equipment Rack for
easy loading, positioning, and unloading.
2. Select the "WASH TIME" (3, 5, or 7 minutes) on the control panel. choose the length of wash time
based on the condition of the item to be washed.
3. Set the "RUN/DRAIN" switch on the control panel to "Run".
4. Select the wash mode ("Clean & Disinfect", "Clean Only," or "Disinfect Only") on the control panel if
your Aqua Phase is equipped with the Disinfectant Application System.
5. Push the "START" button on the control panel.
WASH SEQUENCE
•Set the "RUN/DRAIN" switch to "DRAIN".
•Push the "START" button. The machine will drain the water.
•Prior to beginning the next wash cycle, set the "RUN/DRAIN" switch to "RUN".
•When the next wash cycle begins, the machine will automatically fill with fresh water.
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

DISINFECTANT APPLICATION
SYSTEM (option)
Follow all instructions provided by the manufacturer of the disinfectant solution that you
choose to use including dwell time, application, removal, and proper handling of the
disinfectant.
The Disinfectant Application System allows you to automatically apply a disinfectant solution.
The disinfectant solution used with the Aqua Phase Disinfectant Application System and the
proper use of that disinfectant solution is responsible for the level of disinfection results that
achieved.
Disinfectant Solution:
•The Disinfectant Application System is preset at the factory to apply disinfectant at the rate
of 1 ounce per gallon of water.
•Aqua Phase uses 100 to 110 ounces of water per disinfectant cycle.
•Aqua Phase can provide disinfectant solution products specifically formulated to work with
the Aqua Phase System. Order your solutions by calling your dealer or Aqua Phase at
1-800-208-9274.
OPERATING INSTRUCTIONS
•Be sure that you are using a 1-ounce per gallon disinfectant. If not, see the note below.
•Place a one (1) gallon container of your disinfectant solution in the Chemical Tray
(located inside the Chemical Cabinet at the rear of the Aqua Phase).
oInsert the CLEAR hose into the disinfectant container.
oClose the Chemical Cabinet door.
•At the front of the Aqua Phase, select the desired WASH MODE: Clean Only, Clean and
Disinfect, or Disinfect Only.
Note:
If you choose to use a disinfectant that calls for a different dilution rate, Aqua Phase can be
modified to accommodate that rate. For information on how to make this modification, please
call the factory for assistance or review the Disinfectant Mixing Valve “Dema” technical
information included in this manual.
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

DAILY OPERATIONS
Start-up Procedures:
1. Check that the Aqua Phase Washer is connected to a water supply and that the water supply
is turned on. Then confirm the Aqua Phase Fill and Drain Hose Connections are properly
connected and secure.
2. Check the Primary Filter Screen inside of the Aqua Phase Reservoir to make sure you have a
clean Primary Filter Screen. Make sure that the screen is put back in place properly.
3. Check the chemical supply levels, by looking in the Chemical Cabinet – located in the back,
or side, of your Aqua Phase Washer.
4. Plug in the Aqua Phase and press the ‘Reset’ button located on the GFCI plug.
Operating Procedures
1. Load the item to be washed into the Wash Chamber, then close and latch the front door.
2. Set the ‘Wash Time’ (3, 5, or 7 minutes) selector switch, located on the Control Panel, to the
desired wash time.
3. Set the ‘Run/Drain’ selector switch to ‘Run’.
4. Select the Wash Mode  Only if your Aqua Phase Washer is equipped with the Disinfectant
Application System feature.
5. Push the green ‘Start’ button located on the Control Panel. Aqua Phase Washer will now fill
with water & begin the cycle selected.
6. When cycle is complete, open door of washer.
**Cation when opening the door-steamwill come out of the door. The door and the item
washed may be hot to the touch right away.
Optional Step: Place a drying mat on the floor by the Aqua Phase Washer Door to soak up
water when you remove items from the washer.
7. Take the items out of the washer. On drying mat, tip the wheelchair on its handles to let the
water on the seat run off.
8. Push the red ‘Stop’ button at any time during the cycles if problems arise.
Shut-Down Procedures:
1. When you are finished for the day, set the ‘Run/Dry’ selector switch to ‘Drain’.
2. Press the green ‘Start’ button to completely drain the water out of the washer. Door has to
be closed.
3. Open the door and clean the debris from the Primary Filter Screen – located just inside on
the bottom of the Wash Chamber. Make sure the Filter Screen is put back in place properly.
4. Wipe clean the High Water Level Control (located inside, on the bottom of the Washer
Chamber) clean.
5. Wipe the Low Water Level Control (located inside, on the bottom of the Wash Chamber)
clean.
6. Turn off the water supply to the Aqua Phase Washer.
7. Un-plug the Aqua Phase Washer form the wall/power supply.
8. Open the front door of the Aqua Phase Washer if it will be a couple of days before next use.
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com

DAILY OPERATIONS LOG
Aqua Phase, A Division of Mid-State Stainless, Inc.  330 W. Benson Ave.  PO Box 228  Grantsburg, WI 54840  USA
800-208-9274  715-463-5851  FAX: [phone]  Email: [email protected]  Web: www.aqua-phase.com