Aqua Select 832406KL User manual

7917
AQUA SELECT® HI-RISE REVERSE
BEND STAINLESS STEEL IN POOL
LADDER W/RESIN STEPS
MODEL 832406KL

2
PART # MODEL # DESCRIPTION QTY
1 AC 73008
Reverse Bend Stainless Steel Handrail 2
2 BS MIDSTEP Steps 4
3 BS 698HDWRE Hardware Bag 1
4 BS 698HDWRE Hardware Bag 1
5 BS 698HDWRE Hardware Bag 1
6 BS STPBALL Pivot Ball 1
7 BS BOTSEP Bottom Step 1
AQUA SELECT® HI-RISE REVERESE BEND STAINLESS
STEEL IN-POOL LADDER WITH RESIN STEPS PARTS
1
2
7
3
54
6

3
STEP 1
STEP 2
STEP 3
• Slide one of the four ladder steps(BS MIDSTEP)
onto one of the stainless steel handrails (BS
SSRAIL). Make sure that the step treads are
facing up. (See figure 1)
• If you have any difficulty sliding the step onto
the post, apply a small amount of lubricant to the
posts.
•
Slide the second handrail thru the hole on the
opposite side of the step.
•Align the holes in the step with the top set
of holes on the handrail.
•Secure step to handrail with a bolt and nut
out of hardware bag (BS 698HDWR).
Make sure that the head of the bolt is
located on the outside of the step.
(See figure 2)
• Slide the remaining 3 steps onto the
handrails and secure them with nuts and
bolts. (See figure 3)
Figure 1
Figure 2
Figure 3

4
STEP 4
STEP 5
• Slide the pivot balls (BS STPBALL) onto the
bottom of each handrail as shown in figure 4.
•
Make sure both pivot balls are securely
fastened to each handrail.
• Place the bottom step(BS BOTSTEP) on the
floor facing up. Hold the ladder assembly
straight up and align the pivot balls with the
receivers on the bottom step.
• Push down firmly until both balls are inserted
into the step. See figure 5.
•
Place ladder in your desired position on deck (A).
Swivel step if needed to align with pool floor.
Make sure the base step rests flat against the
pool floor. (B)
•
Mark the location of the handrails on the deck with
a pencil. Using a 1 ½” hole saw, drill one hole for
each hand rail through the deck surface. (C) This will
ensure that the deck will now support the ladder.
•
Secure hand rails to the deck using deck flanges (D).
(FLANGES ARE SOLD SEPERATELY)
•
Slide the flanges over each handrail. Insert the
handrails through the holes in the deck. Secure the
flanges to the deck with screws. Secure the flange
to the handrail by tightening down the screw in the
flange.
STEP 6
Figure 4
Figure 5
A D
C
B
Figure 6

5
LADDER MATS
1. Remove ladder mat from packaging
2. Place ladder mat onto the bottom of the pool with the smooth side facing down towards the liner
3. Place fully assembled ladder on top of the ladder mat. Make sure the ladder is centered on the ladder mat
4. Properly secure ladder to your pool
LADDER MATS ARE SOLD SEPARATELY
FROM YOUR POOL LADDER
HOW TO INSTALL YOUR LADDER MAT
• The use of a ladder mat is strongly recommended with any pool ladder. Ladder mats prevent
your pool liner from being damaged by slight movements of your pool ladder.
USE MODEL 832116
Aqua Select® 9” x 24” Ladder Mat

6
LADDER FLANGES
FLANGES ARE SOLD SEPARATELY
FROM YOUR POOL LADDER
•Ladder Flanges are used to secure your ladder to your deck.