AquaCo SYS-925-3 User manual

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 1of 19
WARNING: For correct operation & installation, it is essential to observe these instructions
TRIPLE UNDERSINK WATER FILTRATION SYSTEM

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 2of 19
CONTENTS
Triple Undersink Water Filtration System........................................................................................................................................... 1
Installation and Operation Manual..................................................................................................................................................... 3
AquaCo Customer Service............................................................................................................................................................... 3
Operation........................................................................................................................................................................................ 3
Installation ...................................................................................................................................................................................... 4
Installation requirements ........................................................................................................................................................... 4
System Dimensions......................................................................................................................................................................... 4
Typical Installation .......................................................................................................................................................................... 5
Components................................................................................................................................................................................ 5
Installation Procedure................................................................................................................................................................. 6
Cartridge Installation/Maintenance................................................................................................................................................ 7
Fluoride Filter Pre-Flush.................................................................................................................................................................. 9
Faucet Installation Procedure....................................................................................................................................................... 11
Battery Installation.................................................................................................................................................................... 12
Battery Replacement & Reset................................................................................................................................................... 12
Led Light Indicator .................................................................................................................................................................... 13
Faucet Maintenance and Care .................................................................................................................................................. 13
Guide to use Push-In Tube Connectors......................................................................................................................................... 13
Use Guidelines .............................................................................................................................................................................. 14
Cartridge Replacement Guide....................................................................................................................................................... 15
Performance Data Sheet........................................................................................................................................................... 16
Notes............................................................................................................................................................................................. 17
Warranty....................................................................................................................................................................................... 17
Price ............................................................................................................................................................................................. 18
Default ......................................................................................................................................................................................... 19
Severence .................................................................................................................................................................................... 19
Warranty/Australia.................................................................................................................................................................... 19

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 3of 19
INSTALLATION AND OPERATION MANUAL
AQUACO CUSTOMER SERVICE
Thank you for purchasing an AquaCo undersink water filter system. Your system is a proven performer manufactured from only
quality materials and components and will give years of ‘spring fresh’ water free of impurities if maintained properly.
Caution: Do not use with water that is microbiologically unsafe or with water of unknown quality without adequate disinfection
before or after the system.
The system is designed for metropolitan supply water but can be used in other situations. For other types of water supply please
contact your local AquaCo stockist or call our AquaCo Customer Service Helpline.
The AquaCo filter systems cartridges need replacing regularly to maintain optimum performance. This is a simple procedure
when following instructions. For cartridge replacements contact your nearest AquaCo stockist.
Customer Service Helpline 08 6156 0220 (Australia).
OPERATION
The AquaCo undersink systems are designed to run economically for many years, dependent on the initial installation and
periodical maintenance.
Flush systems for 10 minutes after any period of non-use more than 2 days. For a period of non-use of 2 weeks or more, it may
be necessary to replace cartridges.
This product must be installed in accordance with local plumbing regulations by a licensed plumber.
Installation Note:
1. If chosen an option with a fluoride filter, the fluoride filter is pre-flushed in our assembly area for the installer convenience.
However, when changing the filters in the future, please follow the instructions in page 9.
2. A water filter system/tap, like any product, has a limited life and may eventually fail. Also, sometimes failure happens early
due to unforeseen circumstances. To avoid possible property damage, this product should be regularly examined for leakage
and/or deterioration and replaced when necessary. A drain pan, plumbed to an appropriate drain or outfitted with a leak
detector, should be used in those applications where any leakage could cause property damage, and/or the water supply should
be turned off if no one is home/present.
INSTALLATION MUST BE COMPLETED BY A LICENCED PLUMBER. FAULTY OPERATION DUE TO UNQUALIFIED PERSONS WILL
RESULT IN VOIDED WARRANTY COVERAGE.

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 4of 19
INSTALLATION
This system comes complete with an installation kit enabling it to be connected to 15mm (½”) copper pipe (cold supply only -
hot water should be filtered prior to heating). Included is a control valve incorporating backflow prevention, anti hammer, flow
control and pressure limiting capabilities in full compliance with the relevant laws.
INSTALLATION REQUIREMENTS
1. 13 mm (½”) Cold water line.
2. Min/Max pressure: 200 - 620 kPa.
3. Min/Max temperature 2° - 38°C (protect from freezing).
4. Suitable location for faucet.
Alternative fittings may be required if being connected to anything other than 15mm (½”) copper pipe. No electrical or drainage
requirements needed.
SYSTEM DIMENSIONS
System Dimensions: 390W x 370 H x 130 D (mm)
Dedicated Drinking Faucet Dimensions: 292 H x 80 W x 130 D (mm)
Note: Instead of having a separate faucet for filtered water, consider having a 3 Way Mixer to avoid drilling a hole through your
stone/wood bench.

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 5of 19
TYPICAL INSTALLATION
Figure 1
COMPONENTS
1. Angle stop valve (Not included)
2. 1/2" Tee with 1/4" Push-in Tube Connector
3. 1/2" Braided Cold-Water Hose (Not included)
4. 1/4" Flexible Red Tubing to Water Filter
5. 350 kPa PLV Pressure Limiting Valve with Dual Check
Valve Built-in
6. Housing Sump with 1st Stage Filter (Sediment Filter)
7. Housing Sump with 2nd Stage Filter (Fluoride or
Carbon Filter)
8. Housing Sump with 3rd Stage Filter (Aragon or
Carbon Filter)
9. Elbow Connector 1/4" Tube to 1/4" Male
10. Straight Adaptor 1/4" Male to 1/4" Tube
11. Stainless Steel Bracket
12. 1/4" Flexible Blue Tubing to Faucet
13. JG 1/4" Tube to 7/16" Female to Faucet
14. High Loop Faucet with LED Indicator

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 6of 19
INSTALLATION PROCEDURE
1. Find a convenient location: The System dimensions are 390 W x 370 H x 130 D (mm), and the tap dimensions are
80 W x 130 D x 292 H (mm).
2. Shut Off the water supply: Locate the connection between the kitchen tap & cold-
water line (Usually a flex line). Shut off the incoming water and open the tap (cold
water) to release the pressure.
3. Disconnect the cold water braided hose.
Note: If you do not know which one is the hot or cold, run the hot water
for a while and feel the hoses.
4. Install the Mains Connector or Isolation Valve: From the cold-water inlet, install
the valve adaptor/mains connector in between. DO NOT apply thread tape to
these connections as they are designed to use the washers only.
5. Connect ¼” RED tube to Mains Connector or Isolation Valve. Push the red tubing
straight into the fitting until it reaches the tube stop.
Then, secure with the red clip.
6. Check for leaks: With the black handle facing in line
with the cold-water line (Fig 3) the valve is in the off position. During this point, you can turn your
water supply back on to check for leaks in the valve installation.
7. Select location on kitchen sink to install faucet. Make sure there is adequate access under
the bench top for the hoses. The faucet supplied with the system requires a ½” hole or 12.5mm
hole. Use a centre punch to locate the position to drill.
8. Drill a pilot hole and gradually enlarge until you have the correct size hole.
9. To install faucet, insert the faucet into the hole in sink or bench. The faucet may be installed on any flat surface over
50mm (2”) in diameter. (Remember: check the underside of the location for interference). Make a small indent using a
centre punch to mark the desired drilling location. Drill a pilot hole with a metal drill. Enlarge the hole using a 1⁄2” metal
drill bit.
10. Once the hole has been drilled install the faucet as per Figure 5 on Page 11. Be sure the faucet body, chrome plate, and
the black rubber washer are placed above the sink. Install the black locating washer, the lock washer and nut
underneath, then tighten firmly while aligning faucet in the desired direction. Connect
BLUE tube to faucet.
11. Reset LED indicator by following instructions on page 12.
12. Install housing assembly by positioning it in the desired location, marking the position
of fixing holes and fixing with mounting screws. Allow room for the connecting tubes
and for removing the filter sumps (50 mm).
13. Fit tubing into connectors (for quick-connect fittings see fig 6 on page 13). Allow slack
in the tubing. Make sure flow is right according to inlet outlet on housing assembly.
For faucet connection see figure 5.
14. Install cartridges as per cartridge installation/changeout on page 7 and 8.
15. Restore the water supply and check for leaks. The filters need to be only hand tight. If they leak then undo housing and
check the O-ring is seated properly.
16. Run the system for at least 10 minutes to remove carbon fines. Water may appear milky, but this is normal and is only
tiny air bubbles that will clear after a short period.
Figure 2
Figure 3
Figure 4

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 7of 19
CARTRIDGE INSTALLATION/MAINTENANCE
To change the filter cartridges, adhere to the following procedure.
1. CLOSE ISOLATING VALVE - Locate
your isolating valve connected to your
cold-water supply. Turn isolating valve
OFF to prevent water flow.
6. CHECK O-RING & FILTER -
Lubricate with food grade silicone
lubricant or similar if needed.
Replace O-ring if kinked or
damaged (Part No: ORG-STD). It is
very important the filter and O-
ring are seated properly in the
housing.
2. OPEN DRINKING TAP - Go to your
drinking faucet and open the tap to
release the pressure.
7. CLOSE THE HOUSINGS - Screw
in housing sump. Tighten the
housing using the spanner
supplied.
3. OPEN THE HOUSING - Loosen the
housings, using the spanner supplied
and unscrew filter housing sumps.
8. REPEAT PROCEDURE - Repeat
procedure from step number #3
until all filters have been
changed.
4. REMOVE CARTRIDGE - When opening
the housings place a container
underneath to catch any spillage.
Cleanse the inside of the housing using
warm water.
9. OPEN ISOLATING VALVE -
Locate your isolating valve
connected to your cold-water
supply. Turn isolating valve ON to
allow water flow.
5. INSTALL NEW CARTRIDGE –Drop in
new filter in the same housing WITH
PACKGING REMOVED. When installing
the new filter, please double check that
the new filter and the current filter have
the same specifications.
10. KEEP DRINKING TAP OPEN -
After installing cartridges KEEP
DRINKING TAP OPEN to flush unit
for 5 - 10 minutes. During this
time, check for any visible drips
or leaks from connections and
fittings. Then, close it.
Water may appear milky, but
this is normal and is only tiny air
bubbles that will clear after a
short period.

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 8of 19
11. RESET LED INDICATOR - Reset LED
indicator by following instructions on
page 12.
16. FINAL CHECK - Once you have
addressed any issues, turn the
water supply back on and
monitor for another 1-2 hours to
ensure that there are no further
leaks.
12. CHECK FOR LEAKS –Check for leaks
rectifying any before leaving the unit.
Ensure that all the connections, fittings,
and housings have been tightened
properly.
Since new filters have been installed,
pay special attention to the gap where
the housings seal.
13. IF LEAKS OCCURR - If you find any
drips or moisture, mark the location.
This will help you locate the issue if you
need to shut off the water and drain the
system for repairs.
14. REMEDIATION - If you detect a leak,
shut off the water supply to the
undersink system immediately.
15. TIGHTEN HOUSINGS, FITTINGS OR
CONNECTIONS - If tightening doesn't
stop the leak, you may need to replace
the faulty component or fitting, or
consider using plumber's tape for
threaded connections. If this occurs,
please contact us on 08 6156 0220.

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 9of 19
FLUORIDE FILTER PRE-FLUSH
To change the filter cartridges, adhere to the following procedure.
1. CLOSE ISOLATING VALVE - Locate
your isolating valve connected to your
cold-water supply. Turn isolating valve
OFF to prevent water flow.
6. CHECK O-RING & FILTER -
Lubricate with food grade silicone
lubricant or similar if needed.
Replace O-ring if kinked or
damaged (Part No: ORG-STD). It is
very important the filter and O-
ring are seated properly in the
housing.
2. OPEN DRINKING TAP - Go to your
drinking faucet and open the tap to
release the pressure.
7. CLOSE ALL HOUSINGS - Screw
in housing sump. Tighten the
housing using the spanner
supplied. Leave the second and
third housings EMPTY.
3. OPEN ALL HOUSINGS - Loosen the
housings, using the spanner supplied
and unscrew filter housing sumps.
8. TURN ON THE WATER - Let
water flow through the water
filter.
4. REMOVE ALL CARTRIDGES - When
opening the housings place a container
underneath to catch any spillage.
Cleanse the inside of the housing using
warm water.
9. OPEN THE DRINKING TAP - Let
water flow through the water
filter to flush the Fluoride
cartridge for at least 10 minutes.
(This water can be collected for
plants if so desired).
5. INSTALL NEW FLUORIDE FILTER
ONLY–Drop in new filter in the same
housing WITH PACKGING REMOVED.
When installing the new filter, please
double check that the new filter and the
current filter have the same
specifications.
10. CLOSE ISOLATING VALVE -
After flushing water through the
Fluoride Removal Cartridge for 10
minutes minimum, turn off the
water supply, turn on the
drinking water filter faucet to
release any water pressure.

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 10 of 19
11. OPEN THE SECOND HOUSING -
Loosen the second housing, using the
spanner supplied and unscrew the filter
housing sump.
17. RESET LED INDICATOR - Reset
LED indicator by following
instructions on page 12.
12. INSTALL SECOND STAGE FILTER –
Drop in new filter in the same housing
WITH PACKGING REMOVED. When
installing the new filter, please double
check that the new filter and the current
filter have the same specifications.
18. CHECK FOR LEAKS –Check for
leaks rectifying any before
leaving the unit. Ensure that all
the connections, fittings, and
housings have been tightened
properly.
Since new filters have been
installed, pay special attention to
the gap where the housings seal.
13. CHECK O-RING & FILTER - Lubricate
with food grade silicone lubricant or
similar if needed. Replace O-ring if
kinked or damaged (Part No: ORG-STD).
It is very important the filter and O-ring
are seated properly in the housing.
19. IF LEAKS OCCURR - If you find
any drips or moisture, mark the
location. This will help you locate
the issue if you need to shut off
the water and drain the system
for repairs.
14. CLOSE THE HOUSING - Screw in
housing sump. Tighten the housing using
the spanner supplied.
20. REMEDIATION - If you detect
a leak, shut off the water supply
to the RO system immediately.
15. TURN ON THE WATER - Let water
flow through the water filter.
21. TIGHTEN HOUSINGS,
FITTINGS OR CONNECTIONS - If
tightening doesn't stop the leak,
you may need to replace the
faulty component or fitting, or
consider using plumber's tape for
threaded connections. If this
occurs, please contact us on 08
6156 0220.
16. KEEP DRINKING TAP OPEN - After
installing cartridges KEEP DRINKING TAP
OPEN to flush unit for 5 - 10 minutes.
During this time, check for any visible
drips or leaks from connections and
fittings. Then, close it.
Water may appear milky, but this is normal
and is only tiny air bubbles that will clear
after a short period.
22. FINAL CHECK - Once you have
addressed any issues, turn the
water supply back on and
monitor for another 1-2 hours to
ensure that there are no further
leaks.

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 11 of 19
FAUCET INSTALLATION PROCEDURE
Figure 5 –Faucet Installation Diagram

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 12 of 19
BATTERY INSTALLATION
BATTERY REPLACEMENT & RESET
1. Remove the black
battery seat from the
faucet lever handle.
1. AFTER ONE YEAR -
When the light flashes
RED indicates your
cartridges are due to be
changed (usage has
exceeded 3,000 minutes
or 12 months).
2. Install battery into
the battery seat,
positive side up,
discard plastic insert.
Note: Keep your hands dry
before installing or
replacing the battery of the
led to prevent the led
circuit board from water or
moisture damage.
2. Remove the black
battery seat from the
faucet lever handle.
3. Reset: When
installing or replacing
battery, it will flash
three times.
3. After one year When
changing cartridges,
please replace the
battery.
Note: Keep your hands dry
before installing or
replacing the battery of the
led to prevent the led circuit
board from water or
moisture damage.
4. Reinstall battery
seat assembly into the
faucet lever, battery
side facing outwards.
The slotted end must
be oriented toward the
faucet.
4. After replacing the
battery, press the RESET
button and hold for 5
seconds until it flashes
RED-BLUE-RED.
5. Open filtered water
with blue signal 5 times
only.
5. Reinstall battery seat
assembly into the
faucet lever, battery
side facing outwards.
The slotted end must be
oriented toward the
faucet.
WARNING! THIS PRODUCT CONTAINS A BATTERY. ACCIDENTAL INGESTION MAY OCCUR AND CAN BE FATAL. PLEASE KEEP OUT OF REACH FROM
INFANTS. IF YOU SUSPECT AN ACCIDENTAL INGESTION, PLEASE CONTACT EMERGENCY SERVICES.

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 13 of 19
LED LIGHT INDICATOR
1. After the battery is installed, the light will flash Blue during operation. The light will flash red after 1 year.
2. When the light flashes RED indicates your cartridges are due to be changed (usage has exceeded 3,000 minutes or 12
months). After changing the battery or replacing the cartridges, please RESET the battery.
3. At the beginning will be flashing BLUE. After 355 days will be flashing YELLOW. Then, after 365 days, will be flashing
RED.
4. To RESET the battery or to program 365 days (1 year): Press for 5 seconds until flashing Red –Blue –Red.
Important note: Battery must be replaced and RESET when changing cartridges.
FAUCET MAINTENANCE AND CARE
Occasional cleaning of aerator is recommended.
1. Use of soapy water and a soft sponge or cloth is recommended.
2. Avoid cleaning with chemicals, solvents or harsh elements. (THIS MAY SERIOUSLY HARM SURFACE AREA)
3. If used with hard water or water with high mineral content, it is absolutely necessary to clean and dry the faucet
immediately after every use. (CALCIUM AND OTHER MINERALS COULD SERIOUSLY DAMAGE SURFACE AREA)
4. Please wipe the canopy and keep your hands dry before installing or replacing the battery of the LED to prevent circuit
board from water or moisture damage.
5. When installing with filtration system with carbon filters or changing carbon filters, it’s suggested to flush the filtered
tubes from the system before connecting with the faucet to prevent possible carbon dust contamination into faucet
cartridge to cause leaking.
GUIDE TO USE PUSH-IN TUBE CONNECTORS
Figure 6

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 14 of 19
USE GUIDELINES
•Minimum operating pressure 200 kPa.
•Maximum operating pressure 620 kPa.
•Do not allow exposure to temperatures below 2°C.
•Maximum operating temperature 38°C.
•Nominal flow rate 3 Lpm.
•This system must be installed according to local plumbing codes on the cold-water line.
•Replacement Cartridges: See Cartridge replacement section (See pages 15).
•This system requires regular replacement of the filter cartridge to maintain proper operation. Varying chlorine,
sediment, or organic substance levels may affect replacement frequency.
•Be sure to change the filter cartridge at least every 12 months; or whenever you detect a change in taste, odour, or
decrease in flow.
•When replacing cartridge, ensure you reset the LED reminder light by removing/replacing the battery from the
rubber seat. Please refer to page 12 for a detailed diagram.
Caution: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or
after the system.

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 15 of 19
CARTRIDGE REPLACEMENT GUIDE
You can obtain replacements from your local AquaCo dealer. To maintain performance, warranty and standards use genuine
AquaCo replacements.
AquaCo 9” x 2.5” Sediment, Fluoride and Aragon Replacement Filters
Set of replacement filter cartridges for the 1st, 2nd and 3rd stage of the AquaCo Triple Undersink Water Filter System.
SKU: REP-925SFA
TO MAINTAIN THE HIGH QUALITY OF THE PURIFIED WATER THE CARTRIDGE(S) NEED CHANGING EVERY 6-18 MONTHS (THIS IS DEPENDENT ON
WATER QUALITY AND USAGE). YOU CAN OBTAIN REPLACEMENT CARTRIDGES FROM YOUR LOCAL AQUACO STOCKIST. TO MAINTAIN PERFORMANCE
AND WARRANTY USE GENUINE AQUACO REPLACEMENTS.

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 16 of 19
PERFORMANCE DATA SHEET
PRODUCT CODE: PP-925-1
SEDIMENT FILTER
Micron Rating
Triple Gradient: 10 μm outer (nominal), 5 μm middle
(nominal), 1 μm inner (nominal)
Filter Dimensions
9” x 2.5”
Media Type
100% Polypropylene
PRODUCT CODE: CB-925-1POP
CARBON FILTER
Micron Rating
>99% @ 1 μm (Nominal)
Filter Dimensions
9” x 2.5”
Initial _P
>5.0 psid @0.75 gpm
Carbon Weight
0.80 lbs.
Carbon Type
Activated Coconut Shell Carbon
PRODUCT CODE: FL-925-OP
FLUORIDE FILTER
Filter Dimensions
9” x 2.5” @ 5 μm (Nominal)
Media Type
Activated Aluminum Oxide
PRODUCT CODE: ARA-925
ARAGON FILTER
Micron Rating
>100% @0.5 μm (Nominal)
Filter Dimensions
9” x 2.5”
Initial _P
>5.0 psid @0.75 gpm
Media Type
Polypropylene, SGS Polymers, Activated Carbon

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 17 of 19
NOTES
AquaCo water care products are designed, manufactured and supported by Water Filters Pty Ltd the name you can trust for
viable and proven water solutions. The complete range of AquaCo products are developed, refined, made to meet and exceed
stringent specifications for the worldwide market.
Important: Sales of products are subject to our Terms and Conditions which are available upon request. All specifications,
information and photos are a guide only and are subject to change without notice. Please ring to confirm details. Warning: For
correct operation of this appliance, it is essential to observe manufacturer’s instructions.
WARRANTY
Any contract of sale, order, or quotation made or accepted by or on behalf of Water Filters Pty Ltd (trading as AquaCo Filters) is
subject to these terms and conditions of sale.
•AquaCo Filters warrants AquaCo Filtration Systems to the original purchaser for a period of 5 years for Retail customers,
and 2 years for Wholesale and Trade customers from the date of sale established by the date of the original invoice
issued by an authorized distributor.
•AquaCo Filters warrants each new Product to be free from defects in the product for a period of 2 year from the date of
retail sale established by the date of the original invoice issued by AquaCo Filters.
•AquaCo Filters reserves the right in instalment sales to grant credit for the value of any Product found to be defective
under this Warranty.
•AquaCo Filters will not cover any labour charge incurred by the Buyer for the replacement or repair of any Product.
•The Buyer is responsible for freight and local labour charges for Products the subject of this Warranty.
•This Warranty applies only to the original purchaser of the Product.
•AquaCo Filters’ obligation under this Warranty is limited to AquaCo Filters’ own option, to either repair or replace the
Product, once AquaCo Filters has deemed that the Product is defective or AquaCo Filters may, at its own discretion,
refund to the Buyer the purchase price paid for the defective goods.
•This Warranty does not cover any Product that is relocated from the site of its original installation.
•All replaced or exchanged parts taken out under this warranty become the property of AquaCo Filters.
•This Warranty is subject to the Product being properly installed, maintained, being used for its intended purpose and
operated strictly in accordance with AquaCo Filters’ recommendations and installation guide.
•This Warranty does not extend to a Product that has been modified in any way unless with AquaCo Filters’ express
consent.
•This Warranty does not cover the normal wear and tear of the Product, or damage caused by misuse, abuse or
vandalism. The Warranty does not cover any malfunction or failure resulting from neglect, use of unauthorised parts
and accessories or use with higher water pressure than indicated on the Product.
•The Warranty does not extend to damage caused by rain, fire, earthquake or other natural causes or acts of nature.
•It is expressly agreed that this shall be the sole and exclusive remedy of the Buyer stated herein, and under no
circumstances shall AquaCo Filters be liable for any costs, loss, expense, damages, special damages, incidental damages
or consequential damages arising directly or indirectly from the design, manufacture, sale, use or repair of the Product
whether based upon warranty, contract, tort or strict liability.
•All Conditions and Warranties implied by law or statute are hereby expressly negatived so far as they lawfully can be.
ACCEPTANCE AND CLAIMS
•Acceptance of the Products shall be deemed for all purposes to have taken place at the expiration from the date of
each delivery.
•Any damage caused during or as a result of transit will not be the responsibility of AquaCo Filters.
•Any faulty systems must be returned with the Pressure Limiting Valve.
•In the event of a Warranty Claim, the Product must be forwarded at the Buyer’s own risk and expense to AquaCo
Filters, together with proof of purchase.

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 18 of 19
•This limited Warranty is void if the Product under Warranty is presented without the said original invoice.
•AquaCo Filters may request that a Statement accompany the Original Invoice, signed by the Buyer, setting out the
following terms:
oThe name and address of the Buyer.
oThe date and by whom the Product was purchased.
oThe date and by whom the Product was installed.
oThe location where the Product was installed.
oThe date and time the Product first appeared to malfunction.
oThe nature of the problem with the Product.
oThe date and time of any and all loss event/s.
oThe date and time AquaCo Filters was first notified of the Product malfunction.
•A failure by the Buyer to submit the said Statement within 28 days, after such request is made by AquaCo Filters, will
automatically void the Warranty.
•A failure to answer truthfully or to answer in a way that is misleading, entitles AquaCo Filters to void the Warranty and
to notify the police in the event of suspected fraudulent conduct.
RISK
•The risk in the Product will pass to the Buyer immediately upon the Product leaving AquaCo Filters’ premises for
delivery to the place designated by the Buyer.
RETENTION OF TITLE
•AquaCo Filters will retain title to (but not risk in) a Product delivered to the Buyer until AquaCo Filters has received
payment in full for such Product from the Buyer.
•The Buyer will store the goods in such a way as to enable them to be separately identified and will keep them insured at
its own expense with AquaCo Filters’ interest noted on any such insurance cover.
•If the Buyer fails to make any payment when due or becomes bankrupt or becomes insolvent, or has a judgement
entered against it in any Court or enters into any scheme of arrangement, composition, or assignment or is in
receivership or voluntary administration or liquidation, the Buyer grants AquaCo Filters the license to enter any of the
Buyer’s premises where the Product is stored, and without notice, to re -take possession of and remove, at the Buyer’s
cost and expense, the Product in respect of which title has not passed to the Buyer.
RIGHTS FORFEITED
The Buyer forfeits any right or claim against AquaCo Filters warrantee if:
1. The System is operated with a water temperature higher than 38° Celsius.
2. The System is not serviced every 12 months. i.e. replacement of filters, PLV check and assessment of general condition
of the system. If the drinking water quality is poor, the System should be serviced before 12 months.
3. The System damage results from water hammer, freezing, neglect or is not installed by a licensed plumber in
accordance with the AS3500 plumbing code and installation plan.
4. The System is subject to water pressure that exceeds the maximum recommended pressure.
5. The System is not installed with an Australian Standards approved Pressure Limiting and Dual Check Valve.
6. The System has been found to be tampered with or if the goods have not been operated or maintained strictly in
accordance with AquaCo Filters’ recommendations.
7. The System is not turned off when the residents are away for over 24 hours.
PRICE
•The price charged shall be AquaCo Filters’ price ruling at the date of delivery unless otherwise agree in writing. Any
price indications or price lists are subject to alterations to AquaCo Filters’ price ruling at the date service or goods
are supplied.
•Prices are as per AquaCo Filters’ wholesale unless otherwise agreed in writing.
•The Buyer is responsible to effect and meet the costs of any insurance cover that is deemed necessary.

Triple Undersink Water Filtration System Installation
Product Code: SYS-925-3
Page 19 of 19
•Clerical errors in computations, typing or otherwise of “catalogue, quotation, acceptance, invoice, delivery docket
or other document” shall be subject to correction.
•Any goods returned through no fault of AquaCo Filters will be subject to a 15% restocking fee.
DEFAULT
On the happening of any one or more of the following events, namely:
•The Buyer fails to make payment to AquaCo Filters on the due date;
•An administrator or liquidator is appointed over any or all of the assets of the Buyer or a scheme of arrangements is
proposed to approve with respect to the Buyer;
•In the case of the Buyer being a natural person, the Buyer commits an act of bankruptcy; then AquaCo Filters may at its
option exercise all or any of the following rights (notwithstanding any prior failure to exercise such rights):
a. demand payment of the whole of the monies owing from the Buyer to AquaCo Filters and the Buyer agrees to
pay the same immediately.
B. the Buyer shall pay to AquaCo Filters interest on such amount outstanding at the rate of 2% per month and
any costs with respect to solicitors, legal advisors, mercantile agents and other agents acting on behalf of
AquaCo Filters in respect of any enforcement hereof or recovery or attempted recovery of monies owing by
the Buyer to AquaCo Filters.
SEVERENCE
If any of these terms or conditions become for any reason wholly or partly invalid, that term or condition shall to the extent of
the invalidity be severed without prejudice to the to the continuing force and validity of the remaining terms and conditions.
JURISDICTION
AquaCo Filters and the buyer agree that this agreement and its provisions shall be construed in accordance with the laws of the
State of Western Australia and be resolved by a Western Australian Court.
WARRANTY/AUSTRALIA
This warranty is given by Water Filters Pty Ltd, ABN 68618671677, telephone no. 08 6156 0220 and email at
[email protected].
This warranty is provided in addition to other rights and remedies you have under law: Our goods come with guarantees which
cannot be excluded under the Australian Consumer Law. You are entitled to replacement or refund for a major failure and to
compensation for other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if
the goods fail to be of acceptable quality and the failure does not amount to a major failure.