1. Read and follow all instructions.
2. A drip loop must be used with all electrical aquarium devices.
A drip loop is a self-made part of the cord hanging below the
receptacle. (See FIG. 1)
WARNING
To guard against injury, basic safety precautions should be observed, including the following:
DANGER
To avoid possible electric shock, special care should be taken since water is employed around the use of
this product. For each of the following situations, do not attempt to repair yourself: return the appliance to
an authorized service facility for service or discard the appliance. Due to the high power consumption of
this heater, we recommend contacting a licensed electrician to ensure you have a proper and safe
electrical breaker available. Failure to do so could lead to product failure, electrical shock or re.
NOTE: It is your sole responsibility to verify that the plug and the receptacle are clean and free of
moisture and salt buildup at all times. The receptacle must be free of water, salt, calcium,
magnesium and dust. Failure to do so can cause re, damage to property, and permanent
damage to the product and personal injury not limited to loss of life.
NOTE: Before installing the unit, check for any signs of damage to the device. If there are any signs of
damage to the device, power cable or plug, do not use and return to place of original purchase.
Thank you for choosing AquaTop’s HERCULES Titanium Heaters. The HERCULES Titanium Heaters offers
precise control to ensure stable water temperatures for all aquatic livestock. Each unit is compatible with
AquaTop’s 1000W and 1500W titanium heaters. With a highly visible dual digital LED display, the TTH
includes adjustable high and low temperature settings with audio alerts. This advanced controller utilizes
heavy-duty, three-prong receptacles and offers overheating protection. Each unit is equipped with a dual
relay interwork that doubles the protection and safety of aquatic life by disabling the heating element in
case of overheating. This highly accurate digital controller eliminates temperature uctuations and is the
perfect addition for saltwater and freshwater systems. May the HERCULES Titanium Heaters help keep
your aquarium temperatures stable and your aquatic creatures warm!
INSTALLATION
PARTS DIAGRAM
1 2
INSTRUCTIONS
1. Connect the controller and heater as shown in Figure #2.
2. Place the heater and the thermal sensor fully into the water. Use the suction cups to securely hold the
heater and thermal sensor.
3. Connect the power plug to a power outlet. Press the “ Increase Temperature” button to choose between
“C” or “F”
4. The “On/Off Light Indicator” will light up if the heater is currently on.
5. Press and hold the “SET” button for few seconds until the numbers on the display ashes.
Next, press the “Decrease Temperature” or “Increase Temperature” button to set the water temperature.
Once selected, press the “SET” button to save the setting. The setting will automatically save in 20 seconds
if the “SET” button has not been pressed.
SAFETY ( VERY IMPORTANT! )
1. To ensure consistent, safe, and accurate water temperature, we recommend only using this heater with
the Aquatop controller designed for this product.
2. Please securely x the heater and the thermal sensor in the aquarium before you connect the AC power.
3. Please always keep the water lever above the “Mini water level”mark on the heater to avoid any damage
of the heater. Under low water level or water shortage status, overheated heater will cause re.
4. Do not use this product in the gravel or sand substrate. This could cause burning of the substrate which
could damage the heater and create a hazardous situation.
5. Before cleaning or moving the heater, please disconnect the power supply and wait at least 30 minutes
until the water and the heater in the tank to cool down before any operation.
6. Only use this heater in a glass tank or sump with proper water movement. Use of this heater in an acrylic
tank or sump, or any type of plastic, could create a hazardous condition
7. To ensure the safety of the user, be sure to connect a power-compatible leakage protection switch during
installation.
8. This product is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
9. Children should be supervised to ensure that they do not play with the appliance.
10. In order to avoid accidents, please check the product every day. If you nd that the water temperature in
the sh tank is abnormal, the product is out of control or other faults, please cut off the power and
stop using the product immediately. Please contact the dealer or the manufacturer for consultation.
Do not disassemble the product or repair yourself.
11. Used for glass aquarium only
INTRODUCTION
READ ALL SAFETY INSTRUCTIONS BEFORE USE
PARTS DIAGRAM / INSTRUCTIONS
INSTALLATION / OPERATION
SPECIFICATIONS
OPERATION
1. Please fully submerge the titanium heater in to the water and rmly x it in the aquarium.
2. Please note that the heater is with a “Minimum water level” mark. Please always keep the water level
above this mark.
3. We strongly recommend that this heater only be used with the included temperature controller.
Attempting to use this unit without the approved controller or with another controller will void the warranty
and could present a safety hazard.
4. The Temperature controller should never be submerged in water or exposed to water. This controller should
be mounted in a location where it will remain dry and easily accessible.
Model Power Consumption Max Aquarium Size Accuracy
TTH-1000 1000 W 200 Gallon ±1.8ºF ( ±1ºC )
TTH-1500 1500 W 300Gallon
