Aqueon 100533612 User manual

*Average output at 12" from the center of the light in a 16" x 16" area.
Owner’s Manual
LED Clip-On Lights
Freshwater
Planted
The PAR graphs are a measurement of visible light output from 400-700nm,
measured at 12” from the center of the light in a 16” x 16” area.
Planted Aquarium Clip-On LED Light PAR @ 12"
Width
PAR
Length
50-70
25-50
0-25
0
8˝
4˝
0˝
-4˝
-8˝
2˝ 4˝ 6˝ 8˝ 10˝ 12˝ 14˝ 16˝
60
40
20
0
8˝
4˝
0˝
-4˝
-8˝
2˝ 4˝ 6˝ 8˝ 10˝ 12˝ 14˝ 16˝
30
20
10
Freshwater Aquarium Clip-On LED Light PAR @ 12"
Width
PAR
Length
20-30
10-20
0-10
Item No. Description PEAK
PAR AVG PAR* PEAK LUX AVG LUX* CCT
100533612 Freshwater 27 15 2060 1225 7,245K
100533613 Planted 63 35 3722 2188 18,400K

Clip-On Light - drip loop
POWER
SUPPLY
CORD
DRIP LOOP
AQUARIUM
APPLIANCE
IMPORTANT SAFETY INSTRUCTIONS
WARNING – To guard against injury, basic safety precautions should be observed including the
following:
1. READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
2. DANGER – To avoid possible electric shock, special care should be taken since water is employed
in the use of aquarium equipment. For each of the following situations, do not attempt to
repair yourself; return the appliance to an authorized service facility for service or discard the
appliance:
A. If the appliance falls into the water, DON'T reach for it! First unplug it and then retrieve it. If
electrical components of the appliance get wet, unplug the appliance completely.
B. Carefully examine the appliance after installation. It should not be plugged in if there is water
on the parts not intended to be wet.
C. Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning or if it
is dropped or damaged in any manner.
D. To avoid the possibility of the appliance plug or receptacle getting wet, position aquarium
stand and tank to one side of the wall-mounted receptacle to prevent water from dripping
onto the receptacle or plug. As shown in the figure, a “drip loop” should be arranged by the
user for each cord connecting an aquarium appliance to the receptacle. The “drip loop” is
the part of the cord below the level of the receptacle, or the connector if an extension cord is
used, to prevent water travel along the cord and coming in contact with the receptacle. If the
plug or the receptacle does get wet,
DON’T unplug the cord. Disconnect the fuse to the circuit breaker that supplies power to the
appliance. Then unplug and examine for the presence of water in the receptacle.
3. Close supervision is necessary when any appliance is
used by or near children.
4. To avoid injury, do not contact moving parts or hot
parts such as heaters, reflectors, lamp bulbs, etc.
5. Always unplug an appliance from the outlet when
not in use, before putting on or taking off parts, and
before cleaning. Never yank the cord to pull plug from
the outlet. Grasp the plug and pull to disconnect.
6. Do not use an appliance for other than intended use.
The use of attachments not recommended or sold
by the appliance manufacturer may cause an unsafe
condition.
7. Do not install or store the appliance where it will be
exposed to the weather or to temperatures below
freezing.
8. Make sure an appliance mounted on a tank is securely
installed before operating it.
9. Read and observe all the important notices on the
appliance.
10. If an extension cord is necessary, a cord with a proper
rating should be used. A cord rated for less amperes
or watts than the appliance rating may overheat. Care
should be taken to arrange the cord so that it will not
be tripped over or pulled.
11. This appliance is recommended for use over a glass aquarium cover or panel. The appliance is
intended FOR HOUSEHOLD USE ONLY.
ONLY FOR POLARIZED ATTACHMENT PLUG APPLIANCES
12. If this appliance has a polarized plug (one blade is wider than the other) as a safety feature, this
plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord
unless plug can be fully inserted. Do not attempt to defeat this safety feature.
13. SAVE THESE INSTRUCTIONS

Fig 2
Fig 3
Fig 1
IMPORTANT CLEANING & SERVICING
PRECAUTIONS
CLEANING: It is important to keep this appliance clean. Unplug and remove the unit from the
aquarium. Wipe exposed surfaces carefully with a damp cloth to remove any dust or mineral
deposits which may collect over time. Make sure all surfaces are dry before reinstalling.
SERVICING: In order to assure proper electrical connections and polarity, replacement parts and
servicing should be performed only by a qualified electrician.
INSTALLATION INSTRUCTIONS
FOR AQUARIUM WITH TOP FRAME (Fig. 1)
1. Ensure glass aquarium cover is properly installed over aquarium.
2. Remove plastic mounting screw from LED light.
3. Place LED light in desired location, making sure the BACK panel of the mounting bracket is flush
with the back panel of the aquarium frame.
oAlways center the fixture so that it provides maximum exposure of light
to all aquarium inhabitants.
4. Insert the plastic mounting screw through the FRONT of mounting bracket. Tighten the screw so
the LED light is secure on the aquarium.
5. Plug-in LED light into an acceptable outlet. Be sure to incorporate a “drip loop”
on the cord.
6. Turn LED light on/off using the touch switch. (Fig. 3)
FOR AQUARIUM WITHOUT TOP FRAME (Fig. 2)
1. Ensure glass aquarium cover is properly installed over aquarium.
2. Remove plastic mounting screw from LED light.
3. Place LED light in desired location, making sure the FRONT panel of the mounting bracket is flush
with the front of the glass panel.
oAlways center the fixture so that it provides maximum exposure of light
to all aquarium inhabitants.
4. Insert the plastic mounting screw through the BACK of mounting bracket. Tighten the screw so
the LED light is secure on the aquarium.
5. Plug-in LED light into an acceptable outlet. Be sure to incorporate a “drip loop”
on the cord.
6. Turn LED light on/off using touch switch. (Fig. 3)

MAINTENANCE
1. Always turn off light fixture and unplug from outlet prior to performing any maintenance.
2. Water spray and water scale can create an electrical and fire safety hazard if allowed to collect
on fixture. To prevent hazard, use over covered aquarium only and clean fixture regularly.
Wipe exterior of fixture down with a clean, freshwater dampened towel. Then dry thoroughly
with a second dry towel. Make sure all surfaces are dry before servicing.
Buy quality fish supplies in our online store.