Takara Belmont LUAR User manual

Although this manual is a separate document from the operation manual, as it describes items that must be
understood by the customer, be sure to store this manual in a secure location together with the operation manual.
1. Move the chair to the installation location.
2. Attach the rubber ring to the base.
Determine the installation location. Lift the base off the floor and attach the rubber ring to the rim of the base.
3. If assembling together with the Yume Swing bowl:
Lock rotation at the Yume Swing setting position where the Yume Swing position setting and the bowl position are optimally aligned. At
that position, manually align the positions of the chair and bowl, and set the preset setting. After completing the setting, return the chair to
its original position by using the auto-return switch, and use the preset switch to check the set position.
4. Provide power to the chair.
Prepare a 230-V AC (7 A or more*) outlet with an attached ground terminal. The chair must absolutely be grounded in order to prevent
electric shock. *220-V AC (7 A or more), 240-V AC (7 A or more), 120-V AC (12 A or more), 110-V AC (12 A or more)
5. Install the step.
1. Raise the legrest. (Refer to "Raising the legrest" on page 14 of the operation manual for the legrest raising procedures.)
2. Holding the step fixture against the positioning stoppers, attach the step fixture to the guide, and securely insert the nuts on the
underside of the step into the two (three for independent legrest type) insertion holes.
(Legrest-step linked type) (Independent legrest type)
LUAR Installation Manual
Installation Procedures
Remove the chair from the wood box. Raise the chair
off the floor by holding the metal plate under the foot
switch (do not hold the plastic parts). Move the chair by
holding the base and body, or the metal plate of the
foot switches. Do not hold the chair by the skirt.
Carrying the chair by the upper part is dangerous
because the base could come off and drop.
Body
Base
Skirt
Foot switches
Rubber ring
Base
It's easier to lift it up one side at a time.
Precautions when extending the adjuster
Adjust the adjuster so that the power cord is not caught or pulled, and the chair does not rub on the floor when
rotating the chair with someone seated in it. Failure to follow this caution can result in an unexpected accident
or damage to the floor.
CAUTION
Adjuster
Adjuster is on
underside.
Legrest
Guide
Positioning
stoppers
Insertion
holes
Step
(underside)
Step fixture
Nuts
Loosen
Extend
Retract
Tighten
Legrest
Guide
Positioning stoppers
Insertion holes
Step fixture
Step (underside)
Nuts
Loosen
Tighten
Extend
Retract
Adjuster is on underside.

Although chair settings are previously set* when shipped from the factory, you can reset them to positions that
suit your needs.
*The legrest is set to the lowest position (folded up) in order to prevent interfering with surrounding equipment
due to faulty or unintentional operation during installation.
1. Turn on the power switch and move the chair to the desired position.
2. With the chair in that position, turn off the power switch.
3. Press and hold the preset switch where you want
to save the setting (P1, P2, or P3), and turn on the
power switch. Keep pressing the preset switch for
approximately three seconds.
▼
Electronic beep is emitted.
4. Setting is completed when the electronic
beep is emitted. Return the chair to its
original position by using the auto-return
switch, and use the preset switch to check
the set position.
●Be very careful when setting the position of the legrest that the customer's leg will not contact equipment or
other items near the chair or other items.
●Perform position setting with a person sitting in the chair. The chair is equipped with a shockless device.
Accordingly, the final operating position varies slightly if position setting is performed without a person sitting in
the chair.
Adjusting Preset Positions
UP/DOWN pedal switch
Control panel (right or left)
Control panel (right or left)
Keep pressing until you
hear an electronic
beep.
WARNING
1E02V3A0