ARCHITETTURA SONORA CUBE 2LV SUB User manual

CUBE 2LV SUB
SPECIFICATIONS
Material
Concrete in four nishings,
marbles, travertine and
alternative stones
Mechanic material
stainless steel, brass,
aluminum and
painted graphite
Dimensions
400 x 400 x 560 mm
Weight
85 kg
SOUND OUTPUT
Speaker type
12” Woofer
Nominal impedence
4 Ω
Crossover
no crossover on board - DSP
needed (LP 100 Hz 18 dB/oct min)
Frequency range
20-150 Hz (-6dB)
Sensitivity (1W-1m)
93 dB
Speaker Peak Power
2000W
Speaker RMS Power
1000W
Min. 500W (Class D)
Unpacking:
NO!
to remove the Cube2LV Sub from the shipping box carefully follow these steps
2.
After removing the strapping
securing the box to the pallet,
lift and remove the box like in
the image, leaving on the
foam protecting the base.
4.
Holding the Cube2LV from the
concrete body, NEVER from the base,
gently turn the module, tilting it into
upper position, WITHOUT removing
the protective foam.
6.
To move the Cube2LV never
drag it on the oor but
ALWAYS lift it as in image 5.
5.
Lifting the speaker holding its body
remove the protecting foam and set it in
its nal position. Do not drag into position
but always lift it as in the gure above.
3.
While turning the speaker,
NEVER handle by its base, but
only by its body! Do not remove
the protective foam till the
speaker is nally positioned.
1.
Due to its size and weight, the
Cube2LV Sub is shipped in a box
secured to a pallet with strapping to
allow its handling and movement into
position with a forklift.
560 400
400

Installation: to install the Cube 2LV on the ground you can take advantange of the new feature, a special base with hollow spaces
carved below that allow - if necessary - the connection of the product in a practical and clean way:
Last update: February 2019
Specication could be changed without notice
Cube 2LV Sub is a subwoofer characterized by a 12" transducer, with a uniform omnidirectional emission. Getting
the diffuser closer to walls or corners, you get an increase of the perceived sound 'intensity'.
Diffusion and
directionality:
to keep your speakers beautiful as long as possible, we warmly recommend doing maintenance at
least once a year. When not in use, sound modules should be appropriately covered or stored
away; heavy duty protective covers are available from AS.
Please refer to the General Manual for appropriate instructions and note that any departure from
our recommendations on care and cleaning, or any evidence of misuse or damages from ordinary
wear and tear, will void all warranty claims.
Maintenance and care:
Amplier with
DSP on board
The standard output cable for the Cube 2LV is vertical coming out from below the base. The cable can run horizontally along the hollow
space carved below or underground. The Cube 2LV, being a passive subwoofer, requires a proper set-up via an amplier with DSP on
board.
bipolar
audio cable
bipolar
audio cable
Plug/socket
IP68 IP69K
connector (supplied)
Connector
to amplier
(not supplied)
Music source
Output cable: Cube 2LV is shipped from the factory with a high performance plug/socket connector (IP68, IP69K) already
attached. The plug (male endend) is connected to the bipolar cable of the sound module and the socket (female
ended) will have to be connected to the cable going to the amplier during nal installation.
Please keep to the following instruction to connect the socket (female ended) to your cable:
- disassemble the socket as in the image on the right.
- connect the positive wire (+) into the hole labelled 1
(take the little pin next to the hole as a reference).
- connect the negative wire (-) into the hole labelled 2.
bipolar
audio cable
bipolar
audio cable
amplier
plug (male ended)
already connected
socket (female ended)
to be connected
Disassembled socket (female ended)
side cable outlet
cable
rubber
feet
hollow for cable
connection
1- 1+
-
Negative >
-
-
White >
or Blue
Brown > +
+
Positive > +