Ardisam Eskimo Quickflip 2 Instruction Manual

GetEskimo.com
ASSEMBLY INSTRUCTIONS & PARTS


69167

69168
OMQUICKFLIP10
Rev. 6/22/2010
© 2010 Ardisam, Inc.
All Rights Reserved.



Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 3
GetEskimo.com
1-800-345-6007
Eskimo Ice Shelters are engineered with you the high performance fisherman in mind. We appreciate your purchase of one of our
high performance ice shelters. Follow these simple instructions and your ice shelter will provide you many years of trouble-free plea-
sure. Save these instructions for future reference.
If for any reason you have a problem with your product, DO NOT return to the retailer, contact the Eskimo customer service depart-
ment at 1-800-345-6007 or by email at [e-mail] for assistance.
CONTENTS
Introduction & Registration .............................................................. 3
Important Safety Precautions.......................................................... 4
Assembly, Set-up & Take-down Instructions............................... 5-13
Long Term Storage ........................................................................ 13
Parts ......................................................................................... 14-19
FAQ’s (Frequently Asked Questions)............................................. 20
Warranty ........................................................................................ 21
Optional Accessories..................................................................... 24
REGISTRATION
Record the model number and serial number (if applicable) in the space provided for easy reference. Fill out and mail the registration
card located in the parts packet. Warranty is valid only if the completed registration card is received by Ardisam, Inc. within 30 days
of purchase.
OWNERSHIP RECORDS
Place of Purchase:
Place of Purchase Address:
City: State/Province: Zip Code/Postal Code:
Model Number: Serial Number Code (found next to
warning tag):
Date of Purchase:
Notes:

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 4
GetEskimo.com
1-800-345-6007
IMPORTANT SAFETY PRECAUTIONS
This tent is made with flame resistant fabric which meets CPAI-84 specifica-
tions. It is not fire proof. The fabric will burn if left in continuous contact with
any flame source.
The application of any foreign substance to the tent fabric may render the
flame resistant properties ineffective.
Heat sources burn oxygen and emit carbon monoxide.Use caution with heaters
and vent properly.
This symbol points out important safety instructions
which if not followed could endanger your personal
safety. Read and follow all instructions in this
manual.
• Do not use candles, matches or open flames of any kind in or near a tent
• Do not cook inside a tent
• Build campfires downwind and several metres away from a tent and be
sure to fully extinguish campfires before leaving a campsite or before
retiring for the night
• Exercise extreme caution when using fuel-powered lanterns or heaters
inside a tent and use battery-operated lanterns whenever possible
• Do not refuel lamps, heaters or stoves inside a tent
• Extinguish or turn off all lanterns before going to sleep
• Do not smoke in a tent
• Do not store flammable liquids inside a tent
WARNING
READ, UNDERSTAND AND FOLLOW ALL ASSEMBLY,
SAFETY, SET-UP & USE INSTRUCTIONS PROVIDED
BEFORE EACH USE. FAILURE TO FOLLOW ALL WARN-
INGS AND INSTRUCTIONS COULD RESULT IN SERI-
OUS INJURY OR DEATH.
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM
THIS TENT FABRIC.
DUETO TRAFFIC ON LAKES, ICE FISHING CAN BE HAZ-
ARDOUS AT NIGHT. IFYOU CHOOSE TO FISH AT NIGHT
OR IN CONDITIONS WITH POOR VISIBILITY, BE SURE
TO TAKE PRECAUTIONS.
NEVER LEAVE THE ICE SHELTER UNATTENDED.
SECURELY ANCHOR THE ICE SHELTER TO THE ICE IN
HIGH WIND CONDITIONS.
LUBRICATE THE SLIDE POLES WITH WD-40® OR A SIL-
ICON SPRAY AT LEAST SEASONALLY. DO NOT USE OIL
OR GREASE AS A LUBRICANT.

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 5
GetEskimo.com
1-800-345-6007
ASSEMBLY INSTRUCTIONS
Tools needed - two 7/16” wrenches and a Phillips screwdriver.
ASSEMBLY NOTE:
-


ASSEMBLY NOTE:



ASSEMBLY NOTE: -


IMPORTANT ASSEMBLYTIP: DO NOT FULLYTIGHTEN ANY NUT
AND BOLT COMBINATIONS UNTIL ALL BOLT-ON PARTS ARE
ASSEMBLED TOGETHER! FINGER TIGHTEN ONLY! THIS WILL
HELP HOLE ALIGNMENT OF ALL PARTS.
FOR QUICKFLIP 2 & EXPRESS 2
1. Attach sled support bar (69677) and the left hinge assembly (69309L) to
the upper lip of sled using (4) provided 1/4-20 x 7/8” bolts, nyloc nuts and
washers. SEE FIGURE 1A.
 


2. Attach sled support bar and the right hinge assembly (69309R) to the upper
lip of sled using (4) provided1/4-20 x 7/8” bolts, nyloc nuts and washers.
    

FOR QUICKFLIP 3
1. Attach the left hinge assembly (68426) to the upper lip of sled using (3)
provided 1/4-20 x 7/8” bolts, nyloc nuts and SAE washers. SEE FIGURE
1B.
 


2. Attach the right hinge assembly (68425) to the upper lip of sled using (3)
provided 1/4-20 x 7/8” bolts, nyloc nuts and SAE washers.
    

         
-





FIGURE 1A (left side shown)
FIGURE 1B (left side shown)
left hinge bracket high side of bracket
(4) 1/4” nuts
(4) 1/4” washers
(4) 1/4” x 7/8” bolts
(3) 1/4” x 7/8” bolts
high side of bracket
left hinge
bracket
(3) 1/4” nuts
(3) SAE washers
sled support bar

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 6
GetEskimo.com
1-800-345-6007
FOR QUICKFLIP 2 ONLY
1. Attach (2) seat kit mount brackets (68430) to each hinge assembly using
(4) provided 1/4-20 x 3/4” hex head bolts and nyloc nuts. Make sure the
mount brackets are positioned in the correct hole locations so seat brace
and seat positions are correct later in instructions. SEE FIGURE 2.
2. Attach (2) seat tube spacers to each seat kit mount bracket using (4)
provided 1/4-20 x 3/4” bolts, nyloc nuts and washers.
3. Attach (2) base tubes (68225) to the top side of seat tube spacers us-
ing (4) provided 1/4-20 x 1-3/4” bolts, nyloc nuts and (8) washers. SEE
FIGURE 3A.
4. a. Attach table (68439) to top of rear base tube and seat brace (68172)
to bottom of rear base tube using (2) provided 1/4-20 x 3” bolts, nyloc
nuts and (4) washers. SEE FIGURE 3A.

SEE FIGURE 3A.
b. Attach front of table to front base tube using (1) provided 1/4-20 x 2”
bolts, nyloc nut and (2) washers. SEE FIGURE 3A.
FIGURE 3A
(2) 1/4” x 3/4” bolts
FIGURE 2 (right side shown)
(2) 1/4” nuts
hinge seat kit mount bracket
front base tube
rear base tube
table
(1) 1/4” x 2” bolt
all nuts are 1/4”
all washers are 1/4”
seat kit mount bracket
seat brace tube
(4) 1/4” x 1-3/4” bolts (2) 1/4” x 3” bolts
seat tube spacer

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 7
GetEskimo.com
1-800-345-6007
5. Attach (2) seat bases (68435) to top of base tubes using (8) provided
1/4-20 x 2-3/4” bolts, nyloc nuts and (16) washers. SEE FIGURE 3B.
6. Attach backrest frame (68433) to each seat base using (4) provided 1/4-20
x 1-1/2” bolts and nyloc nuts. SEE FIGURE 3B. You may now tighten all
nut & bolt assemblies. Be sure not to over tighten or crush tubing
when tightening!
7. Attach (2) removable seat cushions (68162) to the top of seat bases and
snap the side release buckles together. Pull straps tight so seat is not
loose.
8. Attach (2) removable backrest cushions (68163) to the backrest frames
and secure with Velcro.
WARNING
BE SURE SEAT PAD & BUCKLES ARE SECURELY AND COR-
RECTLY ATTACHED TO PREVENT ACCIDENTAL REMOVAL!
FIGURE 3B
base tubes
backrest frame
seat base
all nuts are 1/4”
all washers are 1/4”
(8) 1/4” x 2-3/4” bolts
(4) 1/4” x 1-1/2” bolts
LEFT SIDE
RIGHT SIDE

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 8
GetEskimo.com
1-800-345-6007
FOR QUICKFLIP 3 ONLY
1. Attach (2) seat kit mount brackets (68430) to each hinge assembly using
(4) provided 1/4-20 x 3/4” hex head bolts and nyloc nuts. Make sure the
mount brackets are positioned in the correct hole locations so seat brace
and seat positions are correct later in instructions. SEE FIGURE 4.
2. Attach (2) base tubes (68441) to the top side of seat kit mount brackets
using (4) provided 1/4-20 x 1-3/4” bolts, nyloc nuts and (8) washers. SEE
FIGURE 5A.
3. Attach seat brace (68440) to bottom of rear brace tube using (2) provided
1/4-20 x 2-1/4” bolts, nyloc nuts and (4) washers. SEE FIGURE 5A.
FIGURE 4 (right side shown)
FIGURE 5A
base tubes
(2) 1/4” nuts
(2) 1/4” x 3/4” bolts
hinge seat kit mount bracket
all nuts are 1/4”
all washers are 1/4”
seat kit mount bracket
seat brace
(4) 1/4” x 1-3/4” bolts
(2) 1/4” x 2-1/4” bolts

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 9
GetEskimo.com
1-800-345-6007
4. Attach (3) seat bases to top of base tubes using (12) provided 1/4-20 x
2-3/4” bolts, nyloc nuts and (24) washers. SEE FIGURE 5B.
5. Attach backrest frame to each seat base using (6) provided 1/4-20 x 1-1/2”
bolts and nyloc nuts. SEE FIGURE 5B.You may now tighten all nut &
bolt assemblies. Be sure not to over tighten or crush tubing when
tightening!
6. Attach (3) removable seat cushions (68162) to the top of seat bases and
snap the side release buckles together. Pull straps tight so seat is not
loose.
7. Attach (3) removable backrest cushions (68163) to the backrest frames
and secure with Velcro.
WARNING
BE SURE SEAT PAD & BUCKLES ARE SECURELY AND COR-
RECTLY ATTACHED TO PREVENT ACCIDENTAL REMOVAL!
FIGURE 5B
front base tube
rear base tube
backrest frame
seat base
all nuts are 1/4”
all washers are 1/4”
(12) 1/4” x 2-3/4” bolts
(6) 1/4” x 1-1/2” bolts
LEFT SIDE
RIGHT SIDE

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 10
GetEskimo.com
1-800-345-6007
FOR QUICKFLIP 2 & EXPRESS 2
1. Insert (3) 57.21” horizontal assembly poles (68188) into (6) plastic
corner pieces (68175) by lining up snap button with snap button
holes in plastic corner pieces. Snap into place. Pole will have a
snug fit and may shave some interior plastic off. This is by design
for a good fit. SEE FIGURE 6.
2. Insert (6) 24” vertical assembly poles (68184) into the previously
assembled horizontal pole/plastic corner assemblies by lining up
snap button with the snap button holes in plastic corner pieces.
Snap into place. Poles will have a snug fit and may shave some
interior plastic off. This is by design for a good fit. SEE FIGURE
6.
3. Take the (3) hinge upright poles from each hinge assembly and
insert them into the (3) assembled top cross brace poles (large
loop poles). Push the snap buttons inward and allow cross brace
poles to go over hinge poles and slide them to their shortest height
(transport mode). SEE FIGURE 7.
4. Unfold the skin and locate the Eskimo logo near the zippered door,
which is the front of shelter. With the front of shelter skin laying
face down on the ground, in front of shelter, locate the (3) fabric
sleeves sewn to the bottom seam on front side of shelter. Slide the
54.52” horizontal assembly pole (68189) through the long fabric
sleeve. Insert the horizontal assembly pole into (2) plastic corner
pieces by lining up snap button with snap button holes in plastic
corner pieces. Snap into place. Pole will have a snug fit and may
shave some interior plastic off.This is by design for a good fit. SEE
FIGURE 8.
5. Insert (2) 25.14” vertical assembly poles (68185) through the
short fabric sleeves and into the previously assembled horizon-
tal pole/plastic corner assembly by lining up snap button with
the snap button holes in plastic corner pieces. Snap into place.
Poles will have a snug fit and may shave some interior plastic
off. This is by design for a good fit. SEE FIGURE 8.
6. Take the J-hinge poles from each hinge assembly and insert
them into the assembled bottom cross brace pole assembled in
step 5. Push snap buttons inward and allow cross brace to snap
into place. SEE FIGURE 8.
7. Drape the rest of the shelter skin over the shelter sled, seats
and poles and position it the best you can.
8. Assemble the two sets of door spreader poles (69356 & 69357)
by sliding the male half into the female half and snapping in
place with snap button. SEE FIGURE 9.
FOR QUICKFLIP 3 ONLY
1. Insert (3) 70.02” horizontal assembly poles (68190) into (6)
plastic corner pieces (68175) by lining up snap button with snap
button holes in plastic corner pieces. Snap into place. Pole will
have a snug fit and may shave some interior plastic off. This is
by design for a good fit. SEE FIGURE 6.
FIGURE 7
top brace poles
snap button
upright poles
FIGURE 6
horizontal pole
assembly
plastic corner
vertical pole
assembly

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 11
GetEskimo.com
1-800-345-6007
2. Insert (6) 27.76” vertical assembly poles (68186) into the previ-
ously assembled horizontal pole/plastic corner assemblies by
lining up snap button with the snap button holes in plastic corner
pieces. Snap into place. Poles will have a snug fit and may
shave some interior plastic off.This is by design for a good fit.
SEE FIGURE 6.
3. Take the (3) hinge upright poles from each hinge assembly and
insert them into the (3) assembled top cross brace poles (large
loop poles). Push the snap buttons inward and allow cross brace
poles to go over hinge poles and slide them to their shortest
height (transport mode). SEE FIGURE 7.
4. Unfold the skin and locate the Eskimo logo near the zippered
door, which is the front of shelter. With the front of shelter skin
laying face down on the ground, in front of shelter, locate the (3)
fabric sleeves sewn to the bottom seam on front side of shelter.
Slide the 67.52” horizontal assembly pole (68191) through the
long fabric sleeve. Insert the horizontal assembly pole into (2)
plastic corner pieces by lining up snap button with snap button
holes in plastic corner pieces. Snap into place. Pole will have
a snug fit and may shave some interior plastic off. This is by
design for a good fit. SEE FIGURE 8.
5. Insert (2) 29.64” vertical assembly poles (68187) through the
short fabric sleeves and into the previously assembled horizon-
tal pole/plastic corner assembly by lining up snap button with
the snap button holes in plastic corner pieces. Snap into place.
Poles will have a snug fit and may shave some interior plastic
off. This is by design for a good fit. SEE FIGURE 8.
6. Take the J-hinge poles from each hinge assembly and insert
them into the assembled bottom cross brace pole assembled in
step 5. Push snap buttons inward and allow cross brace to snap
into place. SEE FIGURE 8.
7. Drape the rest of the shelter skin over the shelter sled, seats
adn poles and position it the best you can.
FOR ALL MODELS
1. Unzip door and move to the inside of shelter and extend the (3) top cross
brace poles and snap into place.Place back spreader pole with stud, both
roof spreader poles and both door spreader poles into position by snapping
C-clip over cross brace poles. For back spreader pole, simply place end
with stud into pre-drilled hole in back lip of sled. Attach all Velcro loops to
cross brace poles. SEE FIGURES 9 & 10.
2. Move to outside of shelter. Find the center of the edge trim and line it up
with the center of sled lip on back side of shelter. Pull down on the skin
evenly over the sled lip until it is snug.
 


Temporarily press the edge trim over the skin and sled lip. Using a rubber
mallet may be helpful to press over the sled lip.
FIGURE 9
snap button snapped
in place
FIGURE 8
snap button
bottom
brace pole
assembly
front J-leg
pole
fabric sleeve

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 12
GetEskimo.com
1-800-345-6007
FIGURE 10 (Quickflip 3 shown)
door spreader
poles
spreader poles
3. Secure edge trim in place using #6 3/8” sheet metal screws.
 



4. Push ends of 8’ tow rope through holes provided at the front of sled and
knot each end to secure. This tow rope is designed for manual pulling
by hand only. Do not tow behind a motorized vehicle with rope. For high
speed towing you should purchase the Eskimo Tow Hitch acces-
sory.
IMPORTANT NOTE:





Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 13
GetEskimo.com
1-800-345-6007
SET-UP AND TAKE-DOWN INSTRUCTIONS
SET-UP: From the outside or inside of shelter depending on your
preference, start with the bottom cross brace pole and pull out all
cross brace poles and snap into place. As you pull out each cross
brace pole and snap into place, flip all cross braces over to the in use
position. Secure all spreader poles in between all cross brace poles
by snapping C-clips over cross brace poles.
By removing the back spreader pole and the top back spreader pole,
you can flip the shelter back halfway and use it as a wind break on
nice days.
TAKE-DOWN: Close all window covers, vent covers and zip door
shut. Remove all spreader poles and place in bottom of sled. Starting
with the rear cross brace, push snap buttons in and retract all cross
brace poles to their shortest length. Work from the rear cross brace
to the front cross brace that lies on the ground/ice. Flip all poles back.
Use extreme caution when flipping poles for transport position
and make sure no part of the skin gets pinched, caught or stuck be-
tween any poles or in any pinch points. Fold excess skin inside sled
when complete.
 -


LONG TERM STORAGE
• Always make sure your ice shelter is completely dry before storing
for long periods of time. Storing your ice shelter when damp or wet
may cause mold and mildew damage.
• Remove skin, padded seats and padded backrests from ice shel-
ter sled and poles. Clean all salt, moisture and debris from your
shelter skin
• Store skin, padded seats and padded backrests in a cool, dry
place away from rodents.
• Clean all salt, moisture and debris from the sled and poles of your
shelter. Wipe down poles with WD-40® or similar types of silicon to
deter from corrosion.
 


• Store poles and sled in a cool, dry place.

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 14
GetEskimo.com
1-800-345-6007
QUICKFLIP 2 & EXPRESS 2 PARTS


Quickflip 2 assembledQuickflip 2 hinge assembly (right side shown)
2
19
21
20
21
21
22
7
18
11
7
9
7
15
16
8
16
15
13
14
10
3
1
2
12
17
4
5
5
5
6
4
4
LEFT SIDE
RIGHT SIDE

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 15
GetEskimo.com
1-800-345-6007
REF.
NO. DESCRIPTION PART NO. QTY.
1 WASHER, 1/4” FLAT 48261B 8
2 NUT, 1/4-20 HEX NYLOCK 67538 16
3 BOLT, 1/4-20 X 7/8” HHCS GR5 67541 8
4 CORNER, PLASTIC 7/8 POLE SIZE 68175 8
5 ASSEMBLY, POLE VERTICAL 24.00” 68184 6
6 ASSEMBLY, POLE VERTICAL 25.14” 68185 2
7 ASSEMBLY, POLE HORIZONTAL 57.21” 68188 3
8 ASSEMBLY, POLE HORIZONTAL 54.52” 68189 1
9 POLE ASSEMBLY, TOP FRONT SPREADER
(INCLUDES TWO .706” CLIPS)
68331 1
10 SLED 68380 1
11 POLE ASSEMBLY, BACK SPREADER (INCLUDES
ONE .706” CLIP & ONE .706” STUD)
68422 1
12 SEAT KIT (SEE PAGE 18 FOR PARTS) 68436 1
13 HINGE, ASSEMBLY LEFT SIDE 69309L 1
14 HINGE, ASSEMBLY RIGHT SIDE 69309R 1
15 POLE ASSEMBLY, FRONT TOP SPREADER
(INCLUDES ONE .706” CLIP)
69356 2
16 POLE ASSEMBLY, FRONT BOTTOM SPREADER
(INCLUDES ONE .875” CLIP)
69357 2
17 SUPPORT BAR, SLED 69677 2
18 POLE ASSEMBLY, TOP BACK SPREADER
(INCLUDES TWO .706” CLIPS)
69679 1
19 BOLT, 1/4-20 X 1-1/4” PHILLIPS TRUSS HD GR2 67400 8
20 CAP, HINGE POLE 68305 8
21 POLE ASSEMBLY, MIDDLE UPRIGHT 69652 6
22 POLE ASSEMBLY, J-LEG 69678A 2
ITEMS BELOW NOT SHOWN
- SNAP BUTTON, 1/4” 67501 26
- CLIP, .875” 69124 2
- CLIP, .706” 69134 7
- STUD, .706” 68309 1
- TOW ROPE 67589 1
- SCREW, #6 X 3/8” PHILLIPS TRUSS HD 69629 13
- SHELTER SKIN, RED (QUICKFLIP 2) 68017 1
- SHELTER SKIN, RED (EXPRESS 2) 69208 1
- EDGE TRIM, 1/4” CUT TO 93.5” 69654 1
- WINDOW REPLACEMENT, 8” X 12” 69531 2
- WINDOW REPLACEMENT, 8” X 28” 69533 1
- WINDOW REPLACEMENT, 13.5” X 13.5” 69534 1
REPAIR PARTS
- PATCH KIT, RED KITISP -
QUICKFLIP 2 & EXPRESS 2 PARTS LISTS

          -


Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 16
GetEskimo.com
1-800-345-6007
QUICKFLIP 3 PARTS
7
15
10
7
9
7
13
8
13
12
11
16
14
3
1
2
6
4
5
4
5
5
Quickflip 3 assembledQuickflip 3 hinge assembly (right side shown)
2
19
18
18
17
20
21
LEFT SIDE
RIGHT SIDE

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 17
GetEskimo.com
1-800-345-6007
QUICKFLIP 3 PARTS LISTS
REF.
NO. DESCRIPTION PART NO. QTY.
1 WASHER, SAE 67435 6
2 NUT, 1/4-20 HEX NYLOCK 67538 14
3 BOLT, 1/4-20 X 7/8” HHCS GR5 67541 6
4 CORNER, PLASTIC 7/8 POLE SIZE 68175 8
5 ASSEMBLY, POLE VERTICAL 27.76” 68186 6
6 ASSEMBLY, POLE VERTICAL 29.64” 68187 2
7 ASSEMBLY, POLE HORIZONTAL 70.02” 68190 3
8 ASSEMBLY, POLE HORIZONTAL 67.52” 68191 1
9 ASSEMBLY, POLE SPREADER 43.50” 68340 1
10 ASSEMBLY, POLE SPREADER, BACK
46.75”
68406 1
11 HINGE ASSEMBLY, RIGHT SIDE 68425 1
12 HINGE ASSEMBLY, LEFT SIDE 68426 1
13 POLE ASSEMBLY, 61.06” 68428 2
14 SEAT KIT (SEE PAGE 19 FOR PARTS) 68442 1
15 ASSEMBLY, POLE SPREADER 34.50” 69331 1
16 SLED 69390 1
17 POLE ASSEMBLY, FRONT UPRIGHT 69305A 2
18 POLE ASSEMBLY, MIDDLE UPRIGHT 69300A 4
19 BOLT 1/4-20 X 1-1/4” PHILLIPS TRUSS
HD GR2
67400 8
20 TOP HINGE POLE 68305 8
21 POLE ASSEMBLY, J-LEG 69310A 2
ITEMS BELOW NOT SHOWN
- SNAP BUTTON, 1/4” 67501 24
- CLIP, .706” 69134 9
- STUD, .706” 68309 1
- TOW ROPE 67589 1
- SCREW, #6 X 3/8” PHILLIPS TRUSS HD 69629 13
- SHELTER SKIN, RED 68018 1
- EDGE TRIM, 1/4” CUT TO 114” 69306 1
- WINDOW REPLACEMENT, 8” X 12” 69531 2
- WINDOW REPLACEMENT, 8” X 28” 69533 1
- WINDOW REPLACEMENT, 13.5” X 13.5” 69534 1
REPAIR PARTS
- PATCH KIT, RED KITISP -

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 18
GetEskimo.com
1-800-345-6007
QUICKFLIP 2 SEAT PARTS
REF.
NO. DESCRIPTION
PART
NO. QTY.
1 BOLT 1/4-20 X 3/4” HH GR5 8930 8
2 BOLT 1/4-20 X 2” HHCS GR5 48153 1
3 BOLT 1/4-20 X 1-1/2” HHCS GR5 48240 4
4 BOLT 1/4-20 X 1-3/4” HHCS GR5 48250 4
5 WASHER 1/4” 48261 34
6 BOLT 1/4-20 X 3” HH GR5 ZN 48272 2
7 NUT 1/4-20 HEX NYLOC 67538 27
8 BOLT 1/4-20 X 2-3/4” HHCS GR5 67540 8
9 SEAT PAD RED 68162 2
10 BACKREST PAD RED 68163 2
11 SEAT BRACE WELDMENT 68172 1
12 SPACER, SEAT TUBES 68224 2
13 TUBE, SEAT BASE 68225 2
14 BRACKET, SEAT MOUNT 68430 2
15 BACKREST FRAME WELDMENT 68433 2
16 SEAT BASE WELDMENT 68435 2
17 TABLE 68439 1
17
9
10
15
16
3
7
5
4
8
6
2
13
14
7
5
1
11
13
12

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 19
GetEskimo.com
1-800-345-6007
QUICKFLIP 3 SEAT PARTS
1
2
10
6
5
13
1
11
4
3
8
10
5
7
9
14
12
REF.
NO. DESCRIPTION
PART
NO. QTY.
1 TUBE, SEAT BASE 68441 2
2 BRACKET, SEAT MOUNT 68430 2
3 SEAT BASE WELDMENT 68435 3
4 BACKREST FRAME WELDMENT 68433 3
5 WASHER 1/4” 48261 36
6 BOLT 1/4-20 X 3/4” HH GR5 8930 4
7 BOLT 1/4-20 X 1-3/4” HHCS GR5 48250 4
8 BOLT 1/4-20 X 1-1/2” HHCS GR5 48240 6
9 BOLT 1/4-20 X 2-3/4” HHCS GR5 67540 12
10 NUT 1/4-20 HEX NYLOC 67538 28
11 SEAT PAD RED 68162 3
12 BACKREST PAD RED 68163 3
13 SEAT BRACE WELDMENT 68440 1
14 BOLT 1/4-20 X 2-1/4” HHCS GR5 48271 2

Quickflip™2 (69167), Quickflip™3 (69168) & Express™2 (69802)
Page 20
GetEskimo.com
1-800-345-6007
FAQ’S: (Frequently Asked Questions)
• How can I keep mice and other rodents from damaging my ice shelter?
During the off season, you should always remove your ice shelter skin, padded seats and padded backrests from the sled and
poles and make sure it is dry. Fold skin up, store items in a large plastic container with lid and store in a cool, dry place. The use of
moth balls or dryer sheets may be helpful also.
• My poles are noisy and don’t run as smooth as they did originally. Is there a fix?
Applying WD-40® or a similar type of silicon spray works well for lubricating the poles for easier operation and also deters from cor-
rosion.You should do this maintenance at least seasonal, especially before storing for long term periods. Wipe off excess lubricant
so it does not damage your ice shelter skin. Using a rod with a cloth attached to the end of it, apply the WD-40® or silicon lubricant
to the rag and wipe the inside of the large poles so they have a lubricated surface for the hinge poles to slide on.
• My zipper functions roughly or freezes up from snow/ice. How can I fix this?
You can try a silicon spray to help lubricate it, or purchase an actual Zipper Lube® brand lubricant found in many sporting goods
stores, in the camping section. Either way, use with caution and wipe off excess lubricant so it does not damage your ice shelter
skin.
• For attaching the edge trim to my skin and sled, do I actually drill holes through the skin?
Yes, this is the best way to make a seal between the skin and sled. It also keeps the edge trim securely in place and will not fall off
during transport. If you remove the skin from the poles and sled during the off season, the skin will go back on the same way and
you should be able to use the same holes for the screws as you did the previous season.
• The edge trim is hard to put on the sled lip, is there a secret?
You should apply the edge trim to the sled lip at room temperature which makes it more pliable. The use of a rubber mallet will
help too.
• Why are my windows turning cloudy when they get wet?
Sometimes if your windows get extremely wet, the moisture can penetrate the windows which gives them a cloudy appearance.
This can easily be remedied by removing the windows and bringing them into a warm environment (indoors) and letting the mois-
ture retreat from the window which will clear them back up to the original appearance.
• I have a tear in my skin, how do I repair it?
You can call or e-mail us to purchase a patch kit which consists of a 12” x 12” piece of skin material and an adhesive to apply the
patch to the tear area.This should be done at room temperature. Allow at least 24 hours for adhesive to set to assure proper adhe-
sion.
• My shelter lets some water come through it, how can I remedy that?
You may purchase a seam sealer or silicon spray to help seal the seams to help repel water, such as Camp Dry® which can be
found in many sporting goods stores, in the camping section. See Important Safety Precautions on page 4. Eskimo ice shelters
are not water proof.
• I can see small pin holes in my shelter skin, why?
The coating on the inside of shelter skin is done to help darken the interior. The pin holes are normal and may increase from normal
exposure to the elements or from normal wear and tear. This will not affect the performance of the ice shelter in any way and is
normal.
• I can see cracks on the inside of my shelter skin, why?
This is also normal due to exposure to the elements and normal wear and tear. When you fold your shelter for transport, lines and
creases develop in the fabric. This will not affect the performance of the ice shelter in any way
• Will my ice shelter leak from the small pin holes in skin?
Many variables can come into play. It depends on the outside air temperature, the air temperature inside the shelter, how much heat
you are using inside shelter, etc. Some leaking could occur due to condensation, but that is normal. This can be controlled better
by using the numerous air vents, windows and doors that are on your shelter.
• Do I have to have a tracking kit to tow my ice shelter?
For high speed towing behind a snowmobile or ATV, we highly recommend you purchase a high speed tracking kit so you do not
cause unnecessary or premature damage to your ice shelter sled. If you are only going to pull your ice shelter by hand, a high
speed tracking kit is not necessary, but does make it easier to pull.
• Can I wash my ice shelter skin?
You can use a mild bleach and water solution to get rid of mold or mildew. If you are just wanting to wash your skin, you can use a
mild soap and water mixture. Do not machine wash your skin.