Ardisam 5055 Parts list manual

ARDISAM
.com
OPERATING INSTRUCTIONS &
PARTS EXPLOSIONS
CRT ROTOTILLERS
OMCRT07
Rev. 12/21/06
© Copyright 2006 Ardisam, Inc.
All Rights Reserved. Printed in USA.
5055 6 HP BRIGGS 5155 6 HP BRIGGS
6065VE 6.5 HPVIPER ELECTRIC
R5055H 5.5 HP HONDA

OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS
CRT Models
Page 20 800-345-6007
CRT hANdlEBAR PARTS ExPlOSION
53650(2)
53614
53613
53612
53620
53606(2)
53607(4)
503
53629
60G56
53630(2)
53624
2104(4)
48762(2)
53632
53631(2)
53679
90138(4)
90139(2)
53618(2)

OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS
CRT Models
Page 21800-345-6007
CRT hANdlEBAR PARTS lIST
PART # dESCRIPTION QTY.
2104 Nut Hex Two-Way 3/8-16 6
48762 Bolt 3/8-16 x 1” Carriage 4
503 Bolt 5/16-24x1” HH GR5 1
53606 Nut-Nyloc, #10 2
53607 Nut-Jam, 5/16-24 4
53612 Link 11-5/8” long 1
53613 Link 9-1/2” long 1
53614 Pin Clevis 1/4 x 1-1/2” 1
53618 Belt Guard Clip 2
53620 Spring Compression Forward Arm 1
53624 Handlebar Mount Weldment 1
53629 Cable Mount Bracket 1
53630 Cable - RearTine 39” Sheath 2
53631 Grip Handlebar 1” ID Flangeless 2
53632 Nut Push 1/4” 1
53650 Lever Control RearTine 2
53679 Handlebar Weldment 1
60G56 Nut-Bi-Way Lock, 5/16-18 1
90139 Bolt 3/8-16 x 1” 2
91038 Bolt 3/8-16 x 3/4 Serrated Flange 4
PART # dESCRIPTION QTY.
300500 Grommet, 1/2” ID 1
300501 Nut, Wing M5 x .8 2
300502 Screw, Thumb M5 x .8 2
300503 Wiring Harness (not shown) 1
46122 Battery, 12-Volt 7-Amp 1
46140* Switch, Key 1
4656 Battery Box 1
4657 Cover, Battery Box 1
4660 Solenoid 1
4661 Charger Pigtail 1
4663 Cap, Charger Pigtail 1
53106 Nut, Bi-Way Lock 1/4-20 2
53696 Support, Battery Box 1
69169 Bolt, Phillips Truss Hd 1/4-20 x 3/4” 2
* 46140 - On Model 6065VE the key switch is located on the
engine.
6065vE BATTERY BOx PARTS lIST
6065vE BATTERY BOx ExPlOSION

OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS
CRT Models
Page 22 800-345-6007
CRTTINES & hOOd PARTS ExPlOSION
53698, 53699
8931(2)
8905F(2)
1439(2)
1103C(2)
1103B(2)
8932(2)
1103A(2)
1710(2)
1500CRT2, 1500CRT3
53698
1507
1514
1515
48406
53655
1516(3)
740
804
803
504
802
727A
730
509(2)
53581
1501(4)
69170
394
1501(2)
1511(3)
1508
1507
2001(2)
1900LCRT
719(2)
2104(2)
1103(2)
1501
504(2)
417(2)
1504(2)
1900RCRT
53699
Model 5155, 6065VE
1105

OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS
CRT Models
Page 23800-345-6007
CRTTINES & hOOd PARTS lIST
PART # dESCRIPTION QTY.
1103 Lock Pin 5/16” x 1-3/4” 2
1103A Wheel Lockout Knob (5155,
6065VE) 2
1103B Butterfly Lockout (5155, 6065VE) 2
1103C Snap Ring 1/2” (5155, 6065VE) 2
1105 Spring Clamp w/ Dowel (5155,
6065VE) 2
1439 Flat Washer 1/4” ID (5155, 6065VE) 2
1500CRT2 Transmission Assembly, Lock Pin 1
1500CRT3 Transmission Assembly, Lockout
(5155, 6065VE) 1
1501 Bolt 5/16-18 x 3/4” 7
1504 Gasket, Transmission 2
1507 Gasket, Bearing Cap 2
1508 Rear Bearing Cap 1
1511 Bolt 1/4-20 x 7/8” 3
1514 Front End Cap 1
1515 Seal Oil Drive Shaft 1
1516 Bolt 1/4-20 x 3/4” 3
1710 External Snap Ring 2
1900LCRT Left Tine Set 1
1900RCRT Right Tine Set 4
2001 Bolt 3/8-16 x 1-3/4” 2
2104 Nut, Bi-Way Lock 3/8-16 2
PART # dESCRIPTION QTY.
394 Tail Mount Depth Regulator 1
417 Bolt 5/16-18 x 1/2” HH GR5 2
48406 Black Knob 5/16-18 1
504 Lock Washer Spring 5/16” 3
509 Bolt 1/4-20 x 1/2” 2
53581 Hood Assembly w/Side Shields 1
53655 Drag Weldment 1
53698 Wheel, Left Lock Pin/Right Lockout 1
53699 Wheel, Right Lock Pin/Left Lockout 1
69170 Detent Pin 5/16 x 2” Zinc 1
719 Spring Washer 3/8” 2
727A Forward Belt 1
730 Reverse Belt 1
740 Pulley, Two Groove Transmission 1
802 Bolt 5/16-24 x 3/4” 1
803 Washer 5/16” x 1-1/2” 1
804 Key 3/16” x 1” 1
8905F Spring, Compression (5155,
6065VE) 2
8931 Bolt 1/4-20 X 2” SHCS (5155,
6065VE) 2
8932 Nut 1/4-20 (5155, 6065VE) 2

OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS
CRT Models
Page 24 800-345-6007
CRT mOTOR mOUNT PARTS ExPlOSION
53413
1501(4)
53623
810
504(2)
WF516
743
803
731
804
741, 742
53616
60G56(5)
WF38(2)
2104(2)
53648
1501(4)
60G56(4)
53638
53649
1423(4)
WF516 (4)
60501, 60365E,
501H
2104
1408
WF38(2)
739
53682
48144B
53622
WF516
802(2)
504(2)
1407(2)
1501
53633
2104
1408
WF38(2)
48144B
1416
1418
53696B
53617
53637
WF516
504
810
WF516

OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS
CRT Models
Page 25800-345-6007
CRT mOTOR mOUNT PARTS lIST
PART # dESCRIPTION QTY.
1407 Forward Arm Spring 2
1408 Forward Pulley Idler 2
1416 Clevis Pin 1
1418 Cotter Pin 5/64” x 1/2” 1
1423 Bolt 5/16-18 x 2” 4
1501 Bolt 5/16-18 x 3/4” 9
2104 Nut 3/8-16 4
48144B Bolt 3/8-16 x 2” 2
501H Engine, 5.5 hp Honda (R5055H) 1
504 Lock Washer Spring 5/16” 5
53413 Dip Stick 1
53596B ClevisYoke Zinc Plated 1
53616 Spacer, Engine Weight Block 1
53617 Forward Arm 1
53622 Cable Pull Weldment 1
53623 Motor Mount 1
53633 Belt Guide 1
53637 Forward Arm Bushing 1
53638 Plastic Push-in Rivet 1
PART # dESCRIPTION QTY.
53648 Bumper Guard (5155, 6065VE,
R5055H) 1
53649 Belt Guard 1
53682 Reverse Tine Weldment 1
60501 Engine, 6 hp Briggs & Stratton 1
60565E Engine, 6.5 hp Electric Viper
(6065VE) 1
60G56 Nut Bi-Way Lock 5/16-18 9
731 Two Groove Pulley 3/4” 1
739 Reverse Belt Guide 1
741 Spacer, Drive Pulley .900” (6065VE) 1
742 Spacer, Drive Pulley .550” 1
743 Reverse Arm Bushing 1
802 Bolt 5/16-24 x 3/4” 2
803 Washer 5/16” x 1-1/2” 1
804 Key 3/16” x 1” 1
810 Bolt 5/16-24 x 1” 3
WF38 Flat Washer 3/8” 6
WF516 Flat Washer 5/16” 8

OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS
CRT Models
Page 26 800-345-6007
CRTWhEEl &TIllER ShAFT PARTS ExPlOSION & PARTS lIST
PART # dESCRIPTION QTY.
1500CRT2 Transmission Complete, Lock Pin 1
1500CRT3 Transmission Complete, Lockout 1
1506 Seal-Tiller Housing 4
1600LC1 Main Drive Shaft, LH 1
1601 Bearing-Tapered (Includes Cone &
Race) 2
1700A Wheel Shaft Assembly, Lock Pin 1
1700AD Wheel Shaft Assembly, Lockout
(5155, 6065VE) 1
1701 Key 1/4” x 1” 2
1702 Gear-Worm, Brass, 61Tooth, Wheel
Shaft 1
1703 Shim Set-Axle Spacer Kit 4
1704 Bushing 4
1705 Shim, 1.375 OD x .062” thick, (as
required.) 4
1706 Shim, 1.375 OD x .030” thick, (as
required.) 2
PART # dESCRIPTION QTY.
1801 Tine Shaft 1
1803C Gear-Worm, Brass, 30Tooth, LH,
Tiller Shaft 1
1804 Spacer, 1.250” x 1.000” x .062” thick 4
1805 Shim Set-Bearing Cap 2
1806 Shim, 1.750 OD x .062” thick, (as
required.) 6
1807 Shim, 1.750 OD x .030” thick, (as
required.) 2
1808 Shim, 1.750 OD x .015” thick, (as
required.) 2
1809 Shim, 1.750 OD x .010” thick, (as
required.) 2
1810 Snap Ring-Retainer, Internal 4
494LC Casting, Tiller Transmission Long 1