Areca ARC-12 6 Series User manual

www.areca.com.tw
Areca ARC-12x6 series
Quick Installation Guide
2700-1M1216-2621
4/8 Ports PCIe 3.0
Internal/External 12Gbps SAS RAID Adapters
Checklist
Inspect ARC-12x6 RAID controller from the package. If it
appears damaged, or if any items of the contents listed below
are missing or damaged, please contact your dealer or
distributor.
Step 1: Unpack
1 x Low-profile bracket
1 x 12Gb/s SAS RAID controller in an ESD-protective bag
1 x ARC-12x6 series quick installation guide
•
•
•
Step 2: Power PC/Server Off
Remove the mounting screw and existing bracket from the
rear panel behind the selected PCIe 3.0 slot. Align the
gold-fingered edge on the card with the selected PCIe 3.0
slot. Press down gently but firmly to ensure that the card is
properly seated in the slot. Then, screw the bracket into the
computer chassis.
Step 3: Install the 12Gb/s SAS RAID Controllers
Step 4: Mount the Drives
You can connect the SAS/SATA drives to the controller
through direct cable and backplane solutions. ARC-12x6
SAS RAID adapters can only support up to 8 directly
attached disks(without expansion capability).
Step 5: Install SAS Cable
Please refer to Appendix B and Appendix C of user manual.
Step 6: Adding a FBM/BBM Backup Module (Optional)
Step 8: Power up the System
Step 9: Install the Controller Driver
Step 10: Install ArcHTTP Proxy Server
Step 11: Configure Volume Set
• Driver installation usually takes places as part of operating
system installation. Please refer to Chapter 4 “Diver
Installation” of the user manual for the detailed installation
procedure.
ArcHTTP has to be installed for GUI RAID console (MRAID
storage manager) to run. It is used to launch the web browser
McRAID storage manager. It also runs as a service or daemon
in the background that allows capturing of events for mail and
SNMP traps notification.
Follow the steps below to install the ArcHttp utility.
1. Download ArcHttp proxy server (or MAID software) from
Areca website:
2. Follow the steps on the user manual to complete the
installation
If you need additional information about installation and
start-up of this function, see the ArcHTTP Proxy Server
Installation section in Chapter 5 of the user manual. For SNMP
agent function, please refer to Appendix D of the user manual.
For a new system:
In an existing system:
• To install the controller driver into the existing operating
system. For the detailed installation procedure, please refer
to the Chapter 4 “Driver Installation” of the user manual.
You can create and configure an RAID controller using any of
these tools:
• McBIOS RAID Utility
— BIOS-based menus and keyboard navigation.
• McRAID Storage Manager
— web browser firmware-based utility, which is accessible via
the web browser installed on your operating system. It can be
launched through ArcHttp utility or onboard LAN port.
※Method 1: McBIOS RAID manager
The McBIOS RAID manager is a menu-driven program, residing
in the firmware, which allows you to scroll through various menus
and sub-menus and select among the predetermined configuration
options.
Step 7: Connect Monitor Port - LAN Port (Optional)
User can remote manage the RAID enclosure without
adding any user specific software (platform independent)
via standard web browsers directly connected to the
10/100Mbit RJ45 LAN port.
https://www.areca.com.tw/support/downloads.html

www.areca.com.tw Quick Installation Guide
2700-1M1216-2621
Product Features
Form Factor
I/O Processor
Driver Connector
On-Board Cache
Drive Support
Enclosure Ready
ARC-1216-4i/1226-8i ARC-1216-4x/1226-8x
Low Profile: 64.4(H) x 169.5(L) mm
Management
Dual Core RAID-on-Chip 1.2GHz
1GB on-board DDR3-1600 SDRAM with ECC
4 or 8 12Gb/s SAS, SATA or SSD drives
1 x SFF-8643 / 2 x SFF-8643 1 x SFF-8644 / 2 x SFF-8644
Individual Activity/Faulty Header,
Serial Bus and SGPIO
In-Band: PCIe / Out-of-Band: BIOS, LCD (Optional) and LAN Port
External Serial Bus TEL:[phone] FAX: [phone]
Technical Support: [email protected]
Sales Information: [email protected]
Serial
Attached
SCSI
12
•
•
If you need more detail information, please download ARC-12x6 user manual from the website below:
• https://www.areca.com.tw/products/sasadapters_12x6.html
• https://www.areca.com.tw/support/downloads.html
※Method 2: McRAID Storage Manager From ArcHTTP
1. Start ArcHTTP– Browser Edition:
(1) In Windows, right-click on “Start” menu and choose
“Programs”. Clicking “MRAID” program icon starts the
ArcHTTP utility (From the Start menu, choose Programs >
MRAID > ArcHTTP).
(2) On a Mac, there is one MARID icon showing on your desktop.
This icon is for you to start up the ArcHTTP utility.
2. When you double-click on the “ArcHTTP64”, it shows all RAID
storages available on the system and create an individual RAID
storage icon located on left column of the “ArcHTTP Configura-
tions” screen.
3. Locate “ARC-1216 Web Management” and launch the selected
McRAID storage manager.
Enter RAID storage default User Name “admin” and the Password
“0000” when the login page prompted for it. After logging in, the
McRAID storage manager process starts.
Click on the “Quick Create” in the main menu, your volume is
auto-matically configured based on the number of disks in your
system. You can create a RAID set associated with exactly one
volume set.
The user can change the Raid Level, Capacity, Initialization Mode,
and Stripe Size. A hot spare option is also created, depending on
the exist configuration. Tick on the “Confirm The Operation”
check box and click on the “Submit” button, the RAID set and
volume set will start to initialize. If you prefer to customize your
volume set, please use the “Raid Set Functions” and “Volume Set
Functions”.
See chapter 6 of ARC-12x6 user manual for information on
customizing your RAID volumes using McRAID storage manager.
Otherwise, to begin using the ARC-12x6 right away.
※Method 3: McRAID Manager From LAN Port (Optional)
User can remote manage the ARC-12x6 series without adding
any user specific software (platform independent) via standard
web browsers directly connected to the Gigabit Ethernet RJ45
LAN port. You can find controller Ethernet port default IP address
in McBIOS RAID manager “System Information” option. Launch
the Web Browser-based McRAID storage manager by entering
http://[IP Address] in the web browser.
Type the User Name and Password. The RAID controller default
User Name is “admin” and the Password is “0000”. After entering
the user name and password, click the button to access the
McRAID storage manager.
See the chapter 6 of Web Browser-based Configuration on the
user manual detailing the McRAID storage manager to customize
your RAID configuration.
1. Power on your computer. When prompted, press Tab or F6 to
enter the McBIOS RAID manager message.
2. If you have more than one controller in your system, the
McBIOS RAID manager window appears showing a selection
dialog box listing the SAS RAID controllers, select your
controller, then press Enter.
3. Follow the McBIOS RAID manager to complete the configuration.