Argo AGHP081PH User manual

Thank you for choosing an Argoclima heat pump. Please read this manual carefully before using the unit and retain
it for future reference.
V 09/21
User Manual
Air/water Heat pump
Monobloc
MODELS:
AGHP081PH
AGHP121PH
AGHP161PH
AGHP123PH
AGHP163PH

Notices
Thank you for selecting Argo product. Please read this instruction manual carefully before installing and using the
product, so as to master and correctly use the product. In order to guide you to correctly install and use our product and
achieve expected operating effect, we hereby instruct as below:
(1) This instruction manual is a universal manual, some functions are only applicable to particular product. All the
illustrations and information in the instruction manual are only for reference.
(2) In order to make the product better, we will continuously conduct improvement and innovation. We have the right
to make necessary revision to the product from time to time due to the reason of sales or production, and reserve
the right to revise the contents without further notice.
(3) For personal injury or property loss and damage caused by improper operation such as improper installation and
debugging, unnecessary maintenance, violation of related national laws and rules and industrial standard, and
violation of this instruction manual, etc., we will bear no liability.
(4) The final right to interpret for this instruction manual belongs to Argoclima Spa.

Contents
Safety Notices (Please be sure to abide) ........................................................................................................................ 1
1.General ......................................................................................................................................................................... 2
1.1Menu Page............................................................................................................................................................ 2
1.2Backlight ............................................................................................................................................................... 3
2.Operation Instructions ................................................................................................................................................ 4
2.1ON/OFF ................................................................................................................................................................ 4
2.2Function Setting .................................................................................................................................................... 4
2.3User Parameter Setting....................................................................................................................................... 13
2.4Commissioning Parameter Setting...................................................................................................................... 14
2.5Viewing ............................................................................................................................................................... 24
2.6General Setting ................................................................................................................................................... 28
3.Intelligent Control...................................................................................................................................................... 29
3.1Install Ewpe Smart APP ...................................................................................................................................... 30
3.2Setting of Main Functions.................................................................................................................................... 34
3.3Setting of Other Functions .................................................................................................................................. 35

Operation Instructions
1
Safety Notices (Please be sure to abide)
Do not install the control where it is damp or exposed to direct sunlight.
Once the air conditioning unit is installed where possibly subject to electromagnetic interference, shielded twisted
pairs should be used as signal lines and other communication lines.
Be sure communication lines are wired to the correct ports, or normal communication would fail.
Do not beat, toss or frequently assemble and disassemble this control.
Do not operate the control with wet hands!
INFORMATION FOR THE CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EUROPEAN
DIRECTIVE 2012/19/EU
This appliance may not be scrapped with domestic waste at the end of its life cycle. We call your attention to the
crucial role played by the consumer in the re-use, recycling and other forms of recovery of such waste.
The appliance must be scrapped by a sorted waste disposal centre or by returning it to the retailer (no charge is
levied for this service), when you purchase a new equivalent appliance.
Sorted disposal of electric and electronic equipment prevents the negative effects on the environment and human
health resulting from improper scrapping, and also allows the materials from which it is made to be recovered
and recycled, with significant savings in terms of energy and resources.
The sorted disposal requirement is indicated by the crossed waste bin label affixed to the appliance.

Operation Instructions
2
1. General
(This picture is just for reference)
This display panel uses the capacitor touch screen for input operation. The valid touching area indicates the black
rectangle when the display panel lights off.
This control panel is of high sensitivity and will response to unexpected click by the foreign matters on the display
panel. Therefore, please keep it clean during operation.
1.1 Menu Page
Menu Page
Above the menu, the corresponding icon will be displayed based on the mode and status of the controller.
No Item Description
1 Current mode Current mode
2 Data Current data
3 Time Current time
4 Function setting Go to the user setting page.
5 Parameter setting Go to the parameter setting page.
6 Parameter viewing Go to the parameter viewing page.
7 Commissioning parameters Go to the commissioning parameter setting page.
8 ON/OFF
It is used to turn on or off the unit. “OFF” indicates the unit has turned off and
“ON” indicates the unit has turned on. When there is failure-level error, this
button will turn to OFF once the unit is automatically turned off.
9 General setting Go to the general parameter setting page.

Operation Instructions
3
Icon Description Icon Description
Heating Floor commissioning
Cooling Floor commissioning error
Hot water Card out
Heating + Hot water Defrosting
Hot water + Heating Holiday
Cooling + Hot water WiFi
Hot water + Cooling Back
Quiet Menu page
Sanitation Save
Emergency Error
Error Icon
[Notes]
At any other page, where there is no operation in 10 minutes, the display panel will back to the menu page.
1.2 Backlight
Among the general setting page, when “Back light” is set to “Energy save”, the display panel will light off when
there is no operation in 5 minutes. However, it will light on again by touching any valid area.
When “Back light” is set to “Lighted”, the display panel will be kept lighting on.
It is suggested to set it to “Energy save” so as to extend its service life.

Operation Instructions
4
2. Operation Instructions
2.1 ON/OFF
[Operation Instructions]
At the menu page, by touching ON/OFF, the unit will be turned on/off.
[Notes]
It is defaulted to be OFF upon first power-on.
ON/OFF operation will be memorized by setting “On/Off Memory” to be “On” at the “GENERAL.” setting page.
That is, in case of power failure the unit will resume running upon power recovery. Once “On/off Memory” is set to be
“Off”, in case of power failure the unit will keep “Off” upon power recovery.
ON Page
2.2 Function Setting
[Operation Instructions]
1. At the menu page, by touching “FUNCTION”, it will go to the function setting page as shown in the figure below.
FUNCTION Setting Page
2. At the function setting page, by touching the page turning key, it will access to the last or next page. When
setting is finished, by touching the homepage icon, it will directly back to the homepage; by touching the back icon, it will
back to the upper menu.
3. At the function setting page, by pressing the desired function, it will access to the corresponding setting page of
this option.
4. At the function setting page of some function option, by touching “OK”, this setting will be saved; by touching the
“CANCEL” key, this setting will be canceled.
[Notes]
At the function setting page with setting of any function changed, if the function is set to be memorized upon
power failure, this setting will be saved automatically and memorized upon next power-on.
When there is submenu for the selected function option, by pressing it the control will go directly the setting page
of the submenu.
Function Setting

Operation Instructions
5
No Item Range Default Remarks
1 Mode
Cool
Heat
1. When the water tank is unavailable, then only
“Cool” and “Heat” are available.
2. For the heating only unit, only "Heat" mode, “Hot
water”, and “Heat + hot water” are available.
Heat
Hot water
Cool + Hot water
Heat + Hot water
2 Fast hot water On/Off Off 1. When the water tank is unavailable, it will be
reserved.
3 Cool + hot water Cool/Hot water Cool
1. When the water tank is available, it will be
defaulted to be “Hot water”; when unavailable, it will
be reserved.
4 Heat + hot water Heat/Hot water Heat
1. When the water tank is available, it will be
defaulted to be “Hot water”; when unavailable it will
be reserved.
5 Quiet mode On/Off Off /
6 Quiet timer On/Off Off /
7 Weather depend On/Off Off /
8 Weekly timer On/Off Off /
9 Holiday release On/Off Off
10 Disinfection On/Off Off
When the water tank is unavailable, it will be reserved
The disinfection date ranges from Monday to Sunday.
Saturday is defaulted.
23:00. The disinfection time ranges from
00:00~23:00. 23:00 is defaulted.
11 Clock timer On/Off Off /
12 Temp. timer On/Off Off /
13 Emergen. mode On/Off Off /
14 Holiday mode On/Off Off /
15 Preset mode On/Off Off /
16 Error reset / / Some error can be cleared only when it has been
reset manually.
17 WiFi reset It is used to reset the WiFi.
18 Reset / / It is used to reset all user parameter setting.
2.2.1 Mode
[Operation Instructions]
At the function setting page with the unit turned off, by touching “Mode”, it will go to the mode setting page, where
desired mode can be selected. Then by touching “OK” this setting will be saved and the display panel will back to the
function setting page.

Operation Instructions
6
[Notes]
The default mode is “Heat” upon first power-on.
Mode setting is allowed only when the unit is turned off, otherwise a dialog box will pop up, saying “Please turn off
the system first!”
When the water tank is unavailable, only 'Heat” and “Cool” mode are allowed.
When the water tank is available, “Cool”, “Heat”, “Hot water”, “Cool+ Hot water”, and “Heat+ Hot water” are
allowed.
For the heat pump, the “Cool” mode is allowed; for the heating only unit, “Cool+ Hot water” and “Cool” are
unallowable.
This setting can be memorized upon power failure.
2.2.2 Fast Hot Water
[Operation Instructions]
At the function setting page with the unit turned off, by touching “Fast hot water”, the display panel will go to the
corresponding setting page, where desired option can be selected. Then by pressing “OK” this setting will be saved and
the display panel will back to the function setting page.
[Notes]
This function can be set to “On” only when the water tank is available. When the water tank is unavailable, this
function will be reserved.
It will be memorized upon power failure.
2.2.3 Cool + hot water
[Operation Instructions]
At the function setting page with the unit turned off, by touching “Cool + hot water”, the display panel will go to the
corresponding setting page, where desired option can be selected. Then by pressing “OK” this setting will be saved and
the display panel will back to the function setting page.
[Notes]
When the water tank is unavailable, it will be reserved; when it is unavailable, the default priority will be given to
“How water”.
It will be memorized upon power failure.
2.2.4 Heat + hot water
[Operation Instructions]
At the function setting page with the unit turned off, by touching “Heat + hot water”, the display panel will go to the
corresponding setting page, where desired option can be selected. Then by pressing “OK” this setting will be saved and
the display panel will back to the function setting page.
[Notes]
When the water tank is unavailable, it will be reserved; when it is unavailable, the default priority will be given to
“Hot water”.
It will be memorized upon power failure.

Operation Instructions
7
2.2.5 Quiet Mode
[Operation Instructions]
At the function setting page with the unit turned off, by touching “Quiet mode”, there will be a choice box, where
“Quiet mode” can be set to “On”, “Off”, or “Timer”.
When it is set to “Timer”, it is also required to set the “Start timer” and “End timer”. Unless otherwise stated,
otherwise time setting is all the same.
Timer for Quite Mode
3. This setting will be saved by touching the corner at the upper right corner.
[Notes]
It can be set under both ON and OFF statuses, but will work only when the main unit is turned on.
When it is set to “On”, it will automatically back to “Off” when the main unit is turned off; while it is set to “Timer”,
this setting will remain when the main unit is turned off and can only be canceled manually.
It will be memorized upon power failure.
2.2.6 Weather Depend
[Operation Instructions]
At the function setting page, by touching “Weather depend”, there will be a choice box, where it is able to set it to
“On” or “Off”, and also it is able to set the weather-dependent temperature.
Page of the Weather Depend
[Notes]
When “Weather depend” has been activated; it cannot be deactivated by ON/OFF operation but done manually.
It is available to find the weather-dependent target temperature at that parameter viewing pages.
When this function has been activated, it is still allowed to set the room temperature, however, this setting
becomes valid only when “Weather depend” has been deactivated.
This function can be set to “On” no matter the unit is turned on or off, but works only when the unit is turned on.
This function only works for air conditioning. Under the “Hot water” mode, it cannot be activated.
It will be memorized upon power failure.

Operation Instructions
8
2.2.7 Weekly Timer
[Operation Instructions]
1. At the function setting page, by touching “Weekly timer”, it will go to the setting page as shown below.
2. At the “Weekly timer” setting page, as shown in the figure below, the weekly timer can be set to “On” or “Off”.
3. At the “Weekly timer” setting page, by touching the desired day (Monday ~ Sunday) it will access to the setting
page of this option.
4. At the weekday setting page, it is able to set the timer to “Valid” or “Invalid”. Also, it is able to set three timing
periods, each of which can be set to “Valid” or “Invalid”.
5. Then, by touching the “Save” icon, this setting will be saved.
[Notes]
Three periods can be set for each day. The start time should be earlier than the end time for each period,
otherwise this setting will be invalid. In the same way, the latter should be earlier than the former.
When the weekly timer has been activated, the display panel will act based on the current mode and temperature
setting.
Timer setting for the weekday
“Valid” it indicates this setting works only when “Weekly timer” has been activated, unaffected by the holiday mode.
“Invalid” indicates this setting does not work even though the “Weekly timer” has been activated.
It will be memorized upon power failure.
2.2.8 Holiday Release
[Operation Instructions]
At the function setting page, by touching “Holiday release”, it will go to the corresponding setting page, where it can
be set to “On” or “Off”.
[Notes]
When this function has been activated, at the 'Weekly timer” setting page, some week day can be set to “Holiday
release”. In this case, the setting of the “Weekly timer” at this day is invalid unless it has been manually set to “Valid”.
It will be memorized upon power failure.
2.2.9 Disinfection
[Operation Instructions]
1. At the function setting page, access to “Disinfection” setting page.
2. At the “Disinfection” setting page, it can select the disinfection clock, disinfection temperature and disinfection
week and the corresponding setting page will pop up at the right side.
3. Then, this setting will be saved by touching the “Save” icon.

Operation Instructions
9
[Notes]
This setting can be activated only when “Water tank” is set to “With”. When “Water tank” is set to “Without”, this
function will be deactivated.
This setting can be done no matter if the unit is turned on or off.
When “Emergen.mode”, “Holiday mode”, “Floor debug”, “Manual defrost”, or “Refri. recovery” has been
activated, this function cannot be activated at the same time. When “Disinfection” has been activated, “Emergen.
mode”, “Holiday mode”, “Floor debug” “Manual defrost”, or “Refri. recovery” setting will fail and a window will pop
up, saying “Please disable the disinfect mode!”
“Disinfection” can be activated no matter if the unit is turned on or off. This mode will take priority over the “Hot
water” mode.
When disinfection operation fails, the display panel will tell “Disinfection fail!”. Then, by pressing OK it will be
cleared.
When “Disinfection” has been activated, if communication error with the indoor unit or malfunction of the water
tank heater occurs, it will automatically quit.
It will be memorized upon power failure.
2.2.10 Clock Timer
[Operation Instructions]
1. At the function setting page, access to the “Clock timer” setting page.
2. At the “Clock timer” setting page, it can be set to “On” or “Off”.
3. The option “Mode” is used to time the desired mode; “WOT-Heat” and “T-water tank” is used to set the
corresponding water temperature; “Period” is used to for time setting. After that, by touching the “Save” icon, all settings
will be saved.

Operation Instructions
10
[Notes]
When “Clock timer” has been set and “Hot water” mode is involved, in this case, if “Water tank” is changed to
“Without”, “Hot water” will be automatically switched to “Heat”, and “Cool/Heat + Hot water” will be switched to
“Cool/Heat”.
When “Weekly timer” and “Clock timer” have been set at the same time, the priority will be given to the former.
When the water tank is available, “Heat”, “Cool”, “Hot”, 'Heat + Hot water”, and “Cool + Hot water” are allowed;
however, when the water tank is unavailable, only “Heat” and “Cool” are allowed.
When the end time is earlier than the start time, this setting is invalid.
Water tank temperature can be set only when “Hot water” is involved in the operation mode.
The setting of “Clock timer” only works once. If this setting is needed again, it should be set again.
It will be deactivated when the unit is turned on manually.
This function will be memorized upon power failure.
2.2.11 Temp. Timer
At the function setting page, access to the “Temp.timer” setting page.
At the “Temp.timer” setting page, it can be set to “On” or “Off”.
Select “Period 1”/” Period 2” and a window will pop up, where time period can be set. Then select "WT-Heat1/ WT-
Cool 1/2” and also a window will pop up where temperature can be set.

Operation Instructions
11
[Notes]
When “Weekly timer”, “Preset mode”, “Clock timer” “Temp. timer” have been set at the same time, then the latter
takes the priority.
This setting is valid only when the unit is turned on.
Under the “Cool” or “Cool + Hot water” mode, the setting targets at “WT-Cool”; while under the “Heat” or “Heat +
Hot water” mode, the setting targets at “WT-Heat”.
When start time of period 2 is the same as that of period 1, then the former takes prevalence.
”Temp.timer” is judged based on timer.
During this setting, when temperature is set manually, then this setting will take prevalence.
Under the “Hot water” mode, this function will be reserved.
This function will be memorized upon power failure.
2.2.12 Emergen. Mode
[Operation Instructions]
1. At the function setting page, set the mode to “Heat” or “Hot water”.
2. At the function setting page, select “Emergen.mode” and set it to “On” or “Off”.
3. When “Emergen.mode” has activated, the corresponding icon will appear at the upper side of the menu page.
4. When the mode is not set to “Heat” or “Hot water”, the display panel will tell “Wrong running mode!”
[Notes]
The emergency mode is allowed on conditions that there is some error or protection and the compressor has
stopped at least for three minutes. If the error or protection has not been recovered, the unit can access to the
emergency mode through the wired controller (when the unit is off).
Under the emergency mode, “Hot water” or “Heat” cannot be performed at the same time.
When the running mode is set to “Heat”, if “Other thermal” or “Optional E-Heater” is set to “Without”, the unit
will fail to access to the “Emergen. mode”.
When the unit performs “Heat” under “Emergen. mode” and the controller detects “HP-Water Switch”, “Auxi.
heater 1”, “Auxi. heater 1”, and “Temp-AHLW”, this mode will quit at once. In the same way, when errors mentioned
above occur, “Emergen. mode” cannot be activated.
When the unit performs “Hot water” under “Emergen. mode” and the controller detects “Auxi.-WTH”, this mode
will quit at once. In the same way, when errors mentioned above occur, “Emergen. mode” cannot be activated.
When this function has been activated, “Weekly timer”, “Preset mode”, “Clock timer”,and “Temp timer” will be
deactivated. Beside “On/Off”, “Mode”, “Quiet mode”, “Weekly timer”, “Preset mode”, “Clock timer”,and “Temp timer”
operation are unavailable.
Under “Emergen. mode”, the thermostat does not work.
This function can be activated only when the unit is turned off. If dosing so with the unit keeping “On”, a window
will pop up, saying “Please turn off the system first!”.
“Floor debug”, “Disinfection”, and“Holiday mode” cannot be activated at the same with this function. When
doing so, a window will pop up, saying “Please disable the emergen. mode!”.
Upon power failure, “Emergen. mode” will back to “Off”.
2.2.13 Holiday Mode
[Operation Instructions]
At the function setting page, select “Holiday mode” and set it to “On” or “Off”.
[Notes]
This function can be activated only when the unit has been turned off, otherwise a prompt dialog box will pop up,
saying “Please turn off the system frist!”.
When “Holiday mode” has been activated, the operation mode will automatically switch to “Heat”. Mode setting
and “On/Off' operation through the controller will be unavailable.

Operation Instructions
12
When “Holiday mode” has been activated, the controller will automatically deactivate the “Weekly timer” and
“Preset mode” and “Clock timer” and “Temp.timer”.
Under the “Holiday mode”, when the unit is under the control of room temperature, the set point (room
temperature for heating) should be set to 10°C; when it is under the control of leaving water temperature, the set point
(leaving water temperature for heating) should be 30°C.
When this function has been activated, “Floor debug”, “Emergen.mode”, “Disinfection”, “Manual defrost”,
“Preset mode”, “Weekly timer”, “Clock timer”, and “Temp.timer” cannot be activated at the same time, meanwhile a
window will pop up, saying “Please disable the holiday mode!”.
This function will be memorized upon power failure.
2.2.14 Preset Mode
[Operation Instructions]
At the function setting page, select “Preset mode” and go to the corresponding setting page.
At the time period setting page, each time period can be set to “Valid” or “Invalid”.
The option “Mode” is used to preset the mode; “WOT-Heat” is used to set the leaving cold/hot water temperature;
“Start timer” / “End timer” is used to for time setting. After that, by touching the “Save” icon, all settings will be saved.
[Notes]
When “Preset mode” has been set to “Hot water” and “Water tank” is to set to “Without”, the preset “Hot water”
mode will be automatically switched to “Heat”.
When “Weekly timer” and “Preset mode” both have been set, priority will be given to the latter.
When the water tank is available, the preset mode can be “Heat”, “Cool”, or “Hot water”; however, when the
water tank is unavailable, the preset mode can only be “Heat” or “Cool”.
“Start timer” should be earlier than “End timer”, otherwise a dialog will pop up, saying “time setting wrong”.
The setting for “Preset mode” will works until it has been canceled manually.
When “Start timer” is reached, the unit will perform the preset mode. In this case, mode and temperature setting
are still allowed but will not be saved to the preset mode. When “End timer” is reached, the unit will perform OFF
operation.
This function will be memorized upon power failure.

Operation Instructions
13
2.2.15 Error Reset
[Operation Instructions]
At the function setting page, by touching “Error reset”, a choice box will pop up, where by touching “OK” the error
will be reset and by touching “Cancel” the error will not be reset.
[Notes]
It can be performed only when the unit is turned off.
2.2.16 WiFi Reset
[Operation Instructions]
At the function setting page, by touching “WiFi”, a choice box will pop up, where by touching “OK” , the WiFi setting
will be reset, and by touching “Cancel” the choice box will quit and WiFi will not be reset.
2.2.17 Reset
[Operation Instructions]
At the function setting page, by touching “Reset”, a choice box will pop up, where by touching “OK” all user
parameter settings will be reset and by touching “Cancel” it will back to the function setting page.
[Notes]
This function is allowed only when the unit has turned off.
This function is valid for “Temp. timer”, “Clock timer”, “Preset mode”, “Weekly timer”, and “Weather depend”.
2.3 User Parameter Setting
[Operation Instructions]
1. At the menu page, by touching “PARAMETER”, it will back to the parameter setting page, as shown in the figure
below.
Parameter Setting Page
2. At the menu setting page, by touching the page turning keys, it is able to switch to the page where the desired
parameter is.
3. After that, this setting will be saved by touching “OK” and then the unit will run based on this setting. While this
setting will give up by touching “Cancel”.

Operation Instructions
14
[Notes]
For parameters with different defaults under different conditions, when conditions changes, the default value also
will change as the corresponding condition changes.
All parameters will be memorized upon power failure.
Parameter Setting
No Full Name Displayed Name Range Range Default Remarks
(°C) (°F)
1
Leaving water
temperature for
cooling(T1)
WOT-Cool 7~25°C 45~77°C 18/64°C
2
Leaving water
temperature for
heating (T2)
WOT-Heat
20~60°C 68~140°C 45/113°C High-temp series units
20~55°C 68~140°C 45/113°C Normal-temp series
units
3 Room temperature
for cooling (T3) RT-Cool 18~30°C 64~86°C 24/75°C /
4 Room temperature
for heating (T4) RT-Heat 18~30°C 64~86°C 20/68°C /
5 Water tank
temperature(T5) T-water tank 40~80°C 104~176°C 50/122°C /
6
Leaving water
temperature
difference for cooling
(
Δ
t1)
ΔT-Cool 2~100°C 36~50°C 5/41°C /
7
Leaving water
temperature
difference for cooling
(Δt2)
ΔT-Heat 2~10°C 36~50°C 10/50°C /
8
Leaving water
temperature
difference for water
heating (Δt3)
ΔT-hot water 2~8°C 36~46 C 5/41°C
9
Room temperature
control difference
(Δt4)
ΔT-Room temp 1~50°C 34~41°C 2/36°C /
2.4 Commissioning Parameter Setting
[Operation Instructions]
1. At the menu page, by touching “Commission”, it will access to the commissioning parameter page, where the
left side is for the function setting and the right side is for the parameter setting, as shown in the figure below.

Operation Instructions
15
[Notes]
At the commissioning parameter setting page, when the state of any function changes, the system will automatically
save this change and this change will remain upon power failure.
Do not modify any commissioning parameter except the approved qualified servicemen, as it would give birth to
adverse effects to the unit.
Commissioning Function Setting
No. Item Range Default Description
1 Ctrl. state T-water out/T-room T-water out When “Remote sensor” is set to “With”, it can
be set to “T-room”.
2 2-Way valve
Cool 2-Way valve, On/Off Off It will decide the status of the 2-way valve under
the “Cool” and “Cool + Hot water” modes.
Heat 2-Way valve, On/Off On It will decide the status of the 2-way valve under
the “Heat” and “Heat + Hot water” modes
5 Solar setting With/Without Without
When the water tank is unavailable, this setting
will be reserved.
When it is set to “With”, the solar kitting will work
on its own.
When it is set to “Without”, hot water by the
solar kitting is unavailable.
6 Water tank With/Without Without
7 Thermostat Without/Air/Air+ hot water Without
This setting cannot be interchanged between
“Air” and “Air+ hot water” directly but via
“Without” this option
Each time when “Air” or “Air + hot water” is
switched to “Without”, the unit will go to the OFF
status. Meanwhile, the control will send out
“OFF” command for consecutive 40 seconds (it
is longer than the communication error, and the
“ON” command can be performed only when 40
seconds have been expired.
8 Other
thermal With/Without Without /
9 Optional E-
Heater Off/1/2 Off /
10 Remote
sensor With/Without Without When it set to “Without”, and the “Ctrl. state” will be defaulted to be “T-water out”.
11 Air removal On/Off Off /
12 Floor debug On/Off Off /
13 Manual
defrost On/Off Off /
14 Force mode Off/Force-cool/Force-heat Off /
15 Tank heater Logic 1/Logic 2 Logic 1 This setting is allowed when the water pump is
available and the unit is OFF.
16 Gate-Ctrl. On/Off Off /
17 Current Limit On/Off Off It ranges from 0 to 50A and the default is 16A.
18 Address [1-125] [127-253] 1 /
19 Refri.
recovery On/Off Off /

Operation Instructions
16
Commissioning Parameters Setting
No Full Name Display Name Range Default Remark
1 T-HP max T-HP max 40~55 °C 104~131°C 50/122°C
2 Cool run time Cool run time 1~10min
3min
[2-way valve Off]
5min
[2-way valve On]
3 Heat run time Heat run time 1~10min
3min
[2-way valve Off]
5min
[2-way valve On]
2.4.1 Ctrl. state
[Operation Instructions]
At the commissioning parameter setting page, by touching “Ctrl. state”, it can be set to “T-water out” or “T-room”
[Notes]
When “Remote sensor” is set to “With”, this setting can be set to “T-water out” or “T-room”. When “Remote
sensor” is set to “Without”, this setting can only be set to “T-water out”.
This setting will be memorized upon power failure.