Argus Wi-Bio Instruction Manual

Installation & User Manual V2.022
Contents
Other Access Control Products
standalone products
Also available is a range of fully functional standalone door controls for less
complex door management. This attractive design, with modern aesthetics, will
complement and building.
- 1 and 2 Door Digital Keypads
- Proximity Switch
- Biometric Switch
Features:
- (35 - 1000) users
- Access control
- Door monitoring
- Manager user
- fire and intruder alarm interface
- Backlighting
- Tamper resistant
- 5 amp relays
- Indoor or outdoor use
- Robust polycarbonate housing with stainless steel keys
- Mounts onto a standard electrical back box
Wi-Bio
2
Operation Instructions
3
Installation Diagrams
4
Wiring Diagrams
10
8
Enrolling Door Controls
Finger Placement
Simple Secure Access
www.argusaccess.com

2Operation Instructions
Power Supply 12V DC only
Current consumption 70mA
Current consumption with load (max) 100mA
Relay Contact Rating 5 Amps /240V ac
Operating Temperature -20 C to +60 C
Moisture Resistance IP 65
Dimensions - Surface Mount W. 87mm D. 35mm H. 160mm
Number of Users 10000
Technical Specs
Restoring Factory Settings
Example: To Restore Factory Default Settings
Code Description
55 Restoring Factory Default Settings
Enter
Programming
Code + +
55
(Code) Present Finger
to Confirm
Note: If programming code is lost, Remove the Tamper Wing and hold down the
5 key during power-up and enter the default programming code ‘6666’.
Note: The Door Control can only be defaulted if it is not part of a network.
i.e If the Door Control has not been assigned an address.
To release Security Caps push a
screwdriver into slots on the side
and pull forward.
To attach Security Caps hook tabs
into holes and push on.
Finger Print Switch is mounted to pattress box using security
screws provided. Both Security Caps are
then clipped onto Finger Print
Switch.
Flush Mounting
3
Installation Diagrams

12V Linear
Power supply
Door
Contact
0V
Door
Exit Button
0V
12V Linear
Power supply
Door
Contact
0V
Door
Exit Button
Fire Alarm
Panel
0V
Door
12V
Varistor
OP2
OP1
IP1
IP2
IP3
12V Sounder
Always connect a
varistor between
the lock terminals
Wiring Diagrams with
External IP3 Function
B
A
NC
COM
NO
0V
12V
A
B
0V
Note : Used ONLY for
Wired 485 Network
Connections.
4
Wiring Diagrams
Follow
Relay
- Lock Door
5
Wiring Diagrams
Door
12V
Varistor
OP2
OP1
IP1
IP2
IP3
12V Sounder
Follow
Relay
Common OV from the
Fire Alarm Panel and the OV
from the Door Control to
avoid any ground loop issues.
When the fire alarm
is activated (0V removed
from IP3) the door will
be opened
Always connect a
varistor between
the lock terminals
0V
Wiring Diagrams with
Fire Alarm Override
B
A
NC
COM
NO
0V
12V
A
B
0V
Note : Used ONLY for
Wired 485 Network
Connections.

12V Linear
Power supply
Door
Contact
0V
Door
Exit Button
0V
12V Linear
Power supply
Door
Contact
0V
Door
Exit Button
0V
6
Wiring Diagrams
Interlock OP to
Interlock IP on
2nd Door
Interlock IP from
Interlock OP on
2nd Door
Door
12V
Varistor
OP2
OP1
IP1
IP2
IP3
12V Sounder
Always connect a
varistor between
the lock terminals
Wiring Diagrams with
Interlock Connections
B
A
NC
COM
NO
0V
12V
A
B
0V
Note : Used ONLY for
Wired 485 Network
Connections.
Door
12V
Varistor
OP2
OP1
IP1
IP2
IP3
12V Sounder
Always connect a
varistor between
the lock terminals
Wiring Diagrams with
Alarm Panel Connections
B
A
NC
COM
NO
0V
12V
A
B
0V
Note : Used ONLY for
Wired 485 Network
Connections.
Arm Alarm Input
Arm Output (N/O)
Common OV from the
Intruder Alarm Panel
and the OV from the
Door Control to avoid
any ground loop issues.
Only the Manager User
can activate/deactivate
the Alarm Panel. When the
Alarm Panel is activated all
other users are locked out.
7
Wiring Diagrams

8 Enrolling Door Controls
Assigning a Door Address on Wireless Network
Step Description
1 On the Controller screen: Click ‘Allow Doors to Join this Controller’
All Door Controls that don’t have an address start to beep out the next
available address.
2 Hit any key on the ‘beeping’ Door Control to assign this address.
When a Door Control is assigned an address, all unassigned Door
Controls will start to beep the next available address.
3 When all doors are assigned: Click ‘Secure Network’
Assigning a Door Address on a Wired 485 Network
Step Description
1 Right Click on the Controller Icon & select ‘Manually Assign Addresses’
Follow Step 2 above to complete the process.
Enrolling Door Controls
Adding Door Controls
Step Description
1 Click the Doors Icon on the left hand toolbar on the PC application
2 Click ‘Add New Door’
3 The Door is added to the Controller.
4 Configure the required Door settings : Door Timers, Alarm Options,
Door Options, Timed Actions, Inputs & Outputs.
5 Click ‘Save’ to transmit the changes to the Controller.
Note: Placing the mouse cursor over a door feature will display a description
of the feature.
9

Correct Finger Placement
10 Finger Placement
Incorrect Finger Placement
11
Finger Placement