Opera ARCA SLIDE User manual

INSTALLATION INSTRUCTIONS
Art. 23622S - 23624S - 23822S - 23824S
ARCA SLIDE

ELECTRIC LOCK FOR SLIM FRAME SLIDING DOORS
Heavy duty electric lock with mechanical override to secure a slim sliding door.
Counter lock with bolt release system, retracted when the door is open.
› Stainless steel lock and counter lock body, nickeled tempered steel block pin.
› Opening limited to the duration of the impulse (item 23622S, 23624S) or to
the absence of current (item 23822S, 23824S), equipped with current limiter.
› Body width: 21 mm.
› Item + CF: item provided with �xed striking plate, on request.
TECHNICAL SPECIFICATIONS
Counter lock
25
25
29
35
38
backset 20
7.5
7.5
220 180
20
100 150
25
25
10
10

Close the door and verify the correct retention of the counter lock. Activate
the unlocking command and verify the release of the lock.
INSTRUCTIONS
Item 23622S
Item 23822S
Item 23624S
Item 23824S
Power supply 12 Vdc 24 Vdc
Power consumption 1 A 500 mA
Holding force 800 kg 800 kg
Opening overload Max 50 N Max 50 N
Pin status reporting By means of contact
COM./N.O./N.C.
By means of contact
COM./N.O./N.C.
Do not pull the door open before the unlocking command.
It is recommended to verify periodically the correct locking of the
door, the unhindered reception of the opening command and the
tightening of the installed screws.
CAUTION
4

ELECTRICAL CONNECTIONS
PIN STATUS
REPORTING
OPENING
BUTTON
with item 23622/24S
POWER SUPPLY
WITH TIME DELAY
ITEM 05310
with item 23822/24S
COM.
N.O.
N.C.
N.C.
N.C.
N.O.
N.O.
- PWR
+PWR
POWER SUPPLY: 12 Vdc / 1 A item 23622S/822S
24 Vdc / 500 mA item 23624S/824S
PIN STATUS REPORTING: remote reporting of the inserted/non
inserted pin status.

Connect the positive contact of the lock connector
to the N.O. contact of the timer circuit (instead of the
N.C. contact as depicted in the main electrical diagram).
¹ Item 23822S / 23824S
PIN STATUS
REPORTING
COM.
N.O.
N.C.
COM.
N.C.¹ N.O.¹
+
-
OPENING
BUTTON
+V
-V
N
L
PULS
GND
TIMER CIRCUIT
POWER SUPPLY
Item 23622S¹
Item 23624S¹
COM.
N.C.
N.O. +
-

INSTALLATION
Locate the desired installation position of the electric lock on the frame.
Cut a suitable hole in the frame in order to insert the lock and cut the hole
for the cylinder. Refer to the dimension diagram located in the TECHNICAL
SPECIFICATIONS section.
Connect the correctly wired electrical connector (refer to ELECTRICAL
CONNECTIONS), then install the lock by using suitable screws.
Place the counter lock in face of the lock. Slide to close the door in
order to locate the exact position to make the proper hole into the door.
Cut a hole in the door suitable for the installation of the counter lock.
Install the counter lock by using suitable screws.

FIXED STRIKING PLATE INSTALLATION - Item + CF
TESTING AND MAINTENANCE
In case of opening problems: make sure that lock and counter-lock are
correctly lined up, no external objects interfere with the locking mechanism,
the supplied voltage is correct and no force stronger than 50 N is loaded
to the locking pin while sending the unlocking command.
Item 23622S / 23624S (“FAIL SAFE”): power the lock. After the initial
peak the current consumption drops down to 300 mA. Close the door and
test the retention strength, then send the electrical unlocking command or
use the cylinder to open the door.
Item 23822S / 23824S (“FAIL SECURE”): close the door and test the
retention strength, then send the electrical unlocking command or use the
cylinder to open the door. The unlocking is obtained by providing current.
Place the striking plate in face of the lock. Slide to close the door in
order to locate the exact position to make the proper hole into the door.
Cut a suitable hole in the door, then install the striking plate by using
suitable screws.
Adjust the extension of the locking pin: loosen the “A” screw, turn the locking
pin to adjust its extension, then tighten the “A” screw.
A
70
25
21/27

USER MANUAL
OPERA s.r.l.
Via Portogallo, 43
41122 Modena (MO) - Italy
www.opera-italy.com
[email protected]
[phone]
RoHS
WARNINGS
Please read the following instructions carefully.
The warnings in this manual must be observed in conjunction with the USER MANUAL.
Read and keep this manual in its entirety for the life of the product, including proof
of purchase and warranty. Use only supplied or recommended products.
Do not expose the product to water, weather, high temperatures or strong electro-
magnetic �elds. Do not install in explosive environments or in the presence of
flammable vapours: safety hazard.
Entrust the installation of the electrical part to experienced personnel. Do not make
modi�cations or repair to the electrical or electronic components. Check for proper
grounding when connecting to the power supply.
Disposal of packaging in the appropriate containers is recommended.
REV 05/23