ABH LR6000 User manual

LR6000 INSTALLATION
DETAIL "A"
VERIFY CORRECT BACKSET
AND HORIZONTAL OR VERTICAL
MOUNTING BEFORE DRILLING.
THEN USE BACKSET TEMPLATE
THAT IS SUPPLIED.
INSTALLATION INSTRUCTIONS:
1. Prep door according to LR6000 Series latch template
2. Install latch using either #8 wood screws or 8-32 machine screws (Item 2).
3. Check (1) base assembly (Item 3) to ensure the cam is the position shown in Detail A (See above)
Place the base assembly on the push side of the door by inserting the cam shaft into the latch cam as
detailed above.
4. Check the other base assembly (Item 3) and ensure the cam is the position shown in Detail A
(See above). Place base assembly on the pull side of door by engaging the shaft into the latch cam as
detailed above. Fasten both base assemblies together with (4) 12-24 screws (Item 4) and (4) 12-24
hex nuts (Item 5). Test that cams rotate freely on both sides of the door after tightening the
screws.
5. Install the push handle assembly (Item 7) to the base assembly installed on push side of door using
(2) socket head cap screws (Item 8). Insert (1) stop pin (Item 9) through the push base assembly on
the the same side of the direction the push handle is pointing. Test push handle for proper
operation to be sure stop pin was installed in appropriate base assembly hole.
6. Repeat Step #5 on the pull side of the door for the pull handle assembly (Item 6). Insert (1)
stop pin (Item 9) through the pull base assembly on the opposite side of the direction the pull
handle assembly is pointing. Test pull handle for proper operaton to be sure stop pin was
installed in appropriate base assembly hole.
7. Place covers (Item 10) over handles and fasten each cover with (2) 8-32 screws (Item 11).
LATCH CAM
PARTS LIST
DESCRIPTIONQTYITEM LATCH
11
22
BASE ASSEMBLY23 12-24 X 2-1/2" PTHMS
44
45
HANDLE ASSEMBLY, PULL16
HANDLE ASSEMBLY, PUSH17
6-32 X 3/8" SHCS
48
STOP PIN
29
COVER
210
411
#8 X 3/4"FHWS OR 8-32 X 3/8"FHMS UC
12-24 HEX NUT
8-32 X 3/8" OVAL HEAD M.S.
10
11
11
3
1
8
8
11
11
10
8
8
7
5
9
2
3
CAM SHAFT
4
EDGE GUARD NOTE:
WHEN PREPPING THE DOOR FOR
THE BACKSET, DETERMINE IF THE
DOOR WILL RECEIVE AN EDGE
GUARD, IF SO, THE EDGE GUARD
SHOULD BE INSTALLED FIRST AND
THEN THE PREP FOR THE LATCH
BACKSET SHOULD BE MEASURED
FROM THE OUTSIDE EDGE OF THE
EDGE GUARD.
6
NOTE:
BEFORE MOUNTING BASE ASSEMBLIES,
CAM MUST BE ROTATED AS PER DRAWING
SHOWN IN DETAIL "A".
PATENT PENDING
ALL PREP MOUNTING HOLES
TO BE STRAIGHT & PARALLEL
TO ONE ANOTHER, THIS WILL
HELP PREVENT ANY BINDING
OF MECHANICAL PARTS.
NOTES
1. TRIM CAN BE MOUNTED UP, DOWN, HORIZONTALLY OR VERTICALLY.
2. VISION LITE MUST BE AT LEAST 6" FROM CENTERLINE OF TRIM. **
HORIZONTAL
BACKSET
WITH 5" OR 7"
LEVERS
BACKSET
LEVERS
HORIZONTAL
DOWN
LEVERS
UP
LEVERS PUSHPULL LEVERS
MIXED
PULL
PUSH
** LOCK EDGE
POINTING HINGE EDGE
POINTING
REVISED 11-05-18
PAGE 1 OF 3
LR6000-1-03.DWG
LR6000
Handle
Pointing
Direction
Handle
Pointing
Direction
212 COTTER PIN
12
12
9
1
13 7/64" ALLEN KEY
13
c

REVISED 11-05-18
PAGE 2 OF 3
13/16"
BEVEL EDGE DOOR
UNIVERSAL OR
SQUARE EDGE DOOR
BORE
5-3/8"
4-3/8"
6-5/8"
8-5/8" (4) 1/4" DIA.
THRU HOLES
5/32"
2-1/8" DIA.
THRU HOLE
1-1/8"
C
L
LOCK
&
STRIKE
BACK SET
13/16" 2-1/4"
7"
5"
2-3/4"
3-3/4"
BACK SET
DEPTH OF BORE
DOOR LATCH PROVISIONS
DEPTH
OF
BORE CHART
SEE DEPTH OF
1-1/8" DIA. (MIN)
DRILL FOR #8
WOOD SCREW
(2 PLACES)
LR6000-2-03.DWG
LR6000
[0.900]
29/32"
[1.800]
1-51/64"
[1.800]
1-51/64"
[0.900]
29/32"
[] = DECIMAL DIMENSION
2-1/4"
13/16"
13/16"
BACK SET
#8-32
TAPPED HOLE
(2 PLACES)
1-1/8"
1" DIA. HOLE REQUIRED, 2 PLACES
"HOLE" IN REINFORCEMENT
2-1/8" DIA.
THRU HOLE
5/32"
REINFORCEMENT BY
DOOR MFG.
7"
5"
2-3/4"
3-3/4"
BACK SET
UNIVERSAL OR
SQUARE EDGE DOOR
BEVEL EDGE DOOR
1" DIA. HOLE
(THRU ALL
SUPPORTS)
[0.900]
29/32"
[1.800]
1-51/64"
[1.800]
1-51/64"
[0.900]
29/32"
(4) 1/4" DIA.
HOLES BOTH SIDES
C
L
LOCK
&
STRIKE
WOOD DOORMETAL DOOR
[] = DECIMAL DIMENSION
EDGE GUARD NOTE:
WHEN PREPING THE DOOR
FOR THE BACKSET,
DETERMINE IF THE DOOR
WILL RECEIVE AN EDGE
GUARD, IF SO, THE EDGE
GUARD SHOULD BE
INSTALLED FIRST AND
THEN THE PREP FOR THE
LATCH BACKSET SHOULD
BE MEASURED FROM THE
OUTSIDE EDGE OF THE
EDGE GUARD.
DOOR PREP INFORMATION:
1. BACKSET DIMENSION FROM LOW EDGE OF BEVEL.
2. CENTER PUNCH ALL HOLES.
3. DRILL HOLES (FOR HOLLOW METAL DOORS,
DO NOT DRILL THRU. CENTER PUNCH & DRILL
HOLES FROM BOTH SIDES OF DOOR).
ADA
RECOMMENDED
HEIGHT 44" FROM
FINISHED FLOOR
TO CENTER LINE
-OR-
CHECK LOCAL ORDINANCE
FOR PROPER HEIGHT
USE PROVIDED ORIGINAL FULL SCALE
TEMPLATE TO PREP THE DOOR
VERIFY BACKSET
CENTER LINE
LR6000 PUSH/PULL LATCH - DOOR PREP
c

3/32"
DOOR STOP
MORTAR
GUARD
3-3/8"
(MIN)
1" (MIN)
REINFORCEMENT BY
FRAME MFG.
HALF DOOR THICKNESS
(MEASURED FROM STOP OR
SILENCER WHEN USED)
C
LLOCK & STRIKE
1-1/4"
+1/64
-0
1-1/16"
2-1/16"
2-1/16"
4-7/8"
3-3/8"
3-3/8"
+1/64
-0
#12-24
TAPPED HOLE
(2 PLACES)
LOCK
&
STRIKE
L
C
1" X 1-1/2" MIN CAVITY TO
ACCOMMODATE DUST BOX
C
L
LOCK
&
STRIKE
DRILL FOR #8
WOOD SCREW
(2 PLACES)
L
C
3/32"
27/32"
1-1/2"
1-1/8"
1-1/16"
1-1/16"
2-3/4"
HALF DOOR THICKNESS
(MEASURED FROM STOP OR
SILENCER WHEN USED)
REVISED 11-05-18
LR6000-3-03.DWG
PAGE 3 OF 3
LR6000
WOOD FRAMEMETAL FRAME
THICKNESS
3. Mortise to required strike and box depth.
2. Center strike and mark screw positions.
1. Mark centerline of latch bolt on frame.
FRAME PREP
1-1/4
1-1/4
1-1/23-3/8 4-7/8
4-1/8
3/32
3/8
1/4
1/4
3/8
5/64
1-5/16
1-1/8 9/16
2-3/4
2-1/8
OF LATCH
L
C
(OR SILENCER)
EDGE OF STOP
1/2 DOOR
4. All dimensions in inches.
1/32
15/16
4-3/4
1-5/32
4-1/8
3-1/4 3-3/16
1"
1/16
3/8
3/16
1-11/16
1/2
21/32
PREP FOR #8 SCREW
1-3/16
2-1/4
1-11/16
1
1
1-11/16
1/2
21/32
1-3/16
3/16
1/16
3/8
9/64
2-1/4
1-11/16
1/32
9/16
1-3/16
1-5/32
61/64
2-1/8
2-11/16
1-1/4
PREP FOR #8 SCREW
PREP FOR #8 SCREW
1"
PREP FOR #12 SCREW
1-1/2"
DOOR STOP
LR6000 PUSH/PULL LATCH - FRAME PREP
(ASA STRIKE SHOWN FOR EXAMPLE) ("T" STRIKE SHOWN FOR EXAMPLE)
LOCK & STRIKE
ASA STRIKE & DUST BOX "T" STRIKE & DUST BOX "D" STRIKE
601LB STRIKE
c