Ariston AML 125 User manual

1
GB
English,1
Contents
Installation, 2-3
Unpacking and levelling, 2
Electric and water connections, 2-3
The first wash cycle, 3
Technical details, 3
Washer-dryer description, 4-5
Control panel, 4
Leds, 5
Starting and Progra es, 6
riefly: how to start a programme, 6
Programme table, 6
Personalisations, 7
Setting the temperature, 7
Set the drying cycle, 7
Functions, 7
Detergents and laundry, 8
Detergent dispenser, 8
Preparing your laundry, 8
Special items, 8
Woolmark Platinum Care, 8
Precautions and advice, 9
General safety, 9
Disposal, 9
Saving energy and respecting the environment, 9
Care and aintenance, 10
Cutting off the water or electricity supply, 10
Cleaning your appliance, 10
Cleaning the detergent dispenser, 10
Caring for your appliance door and drum, 10
Cleaning the pump, 10
Checking the water inlet hose, 10
Troubleshooting, 11
Service, 12
efore calling for Assistance, 12
WASHER-DRYER
AML 125
Instructions for use
GB
Downloaded from www.Manualslib.com manuals search engine

2
GB
Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the Washer-dryer to inform the
new owner as to its operation and features.
Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the Washer-dryer.
2. Check whether the Washer-dryer has been
damaged during transport. If this is the case, do not
install it and contact your retailer.
3. Remove the four
protective screws and
the rubber washer with
the respective spacer,
situated on the rear of
the appliance (see
figure).
4. Seal the gaps using the plastic plugs provided.
5. Use the plug provided to seal the three holes
where the plug was housed, situated on the lower
right-hand side on the rear of your appliance.
6. Keep all the parts: you will need them again if the
Washer-dryer needs to be moved to another
location.
Packaging materials are not children's toys.
Levelling
1. Install the Washer-dryer on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or other.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or
loosening the adjustable
front feet (see figure);
the angle of inclination,
measured according to
the worktop, must not
exceed 2°.
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the Washer-
dryer.
Electric and water connections
Connecting the water inlet hose
1. Connect the supply
pipe to the water mains
using a gas 3/4
attachment, fitting the
rubber gasket and the
filter supplied with the
appliance and ensuring
that they are fimly
tightened to the taps.
The water supply marked
C must be connected to the cold water tap; the pipe
marked H must be connected to the hot water tap.
oth pipes may be connected to the cold water tap
using the special Y connection with multiple
attachments, supplied with the appliance (see figure).
efore making the connection, allow the water to run
freely until it is perfectly clear.
2. Connect the other end
of the water inlet hose to
the Washer-dryer,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance
(see figure).
3. Make sure there are no kinks or bends in the hose.
The water pressure at the tap must be within the
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Installation
Downloaded from www.Manualslib.com manuals search engine

3
GB
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from the
floor;
alternatively, place it
over the edge of a
basin, sink or tub,
fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
 We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electric connection
efore plugging the appliance into the mains socket,
make sure that:
 the socket is earthed and in compliance with the
applicable law;
 the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (on the right);
 the supply voltage is included within the values i
ndicated on the Technical details table
(on the right);
 the socket is compatible with the washer
dryer's plug. If this is not the case, replace the
socket or the plug.
 The Washer-dryer should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
 When the Washer-dryer is installed, the mains
socket must be within easy reach.
 Do not use extensions or multiple sockets.
 The power supply cable must never be bent or
dangerously compressed.
 The power supply cable must only be replaced by
an authorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
ServiceTroubleshootingPrecautions CareProgra es DetergentsInstallation Description
65 - 100 cm
Technical details
Model AML 125
Di ensions
59.5 cm wide
85 cm high
53.5 cm deep
Capacity from 1 to 5 kg for the wash programme;
from 1 to 4 kg for the drying programme
Electric
connections
voltage 230/240 Volts 50 Hz
maximum absorbed power 2050 W
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres
Spin speed up to 1200 rpm
Control
progra es
according to
IEC456 directive
Wash: programme 3; temperature
60°C; run with a load of 5 kg.
Drying: first drying cycle performed
with a 1 kg load, by selecting a
drying time of 40 min;
Second drying cycle performed with
a 4 kg load and the DRYING knob
on the setting.
This appliance is compliant with the
following European Community
Directives:
- 73/23/CEE of 19/02/73 (Low
Voltage) and subsequent amendments
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments
Downloaded from www.Manualslib.com manuals search engine

4
GB
Control panel
Washer-dryer description
Detergent dispenser
Programme key
START/STOP
utton
START/RESET
utton
TEMPERATURE
Knob
PROGRAMME
Knob
Leds
FUNCTION
uttons
DRYING
Knob
ON-OFF/DOOR LOCK l
Led
Detergent dispenser: to add detergent and fabric
softener (see page 8).
Progra e key: to consult a straightforward
chart of the different programmes available: pull the
grey tab outwards to open it.
LEDS: to find out which wash cycle phase is under
way.
If the Delay Timer function has been set, the time
left until the programme starts will be indicated (see
page 5).
DRYING knob: to set the desired drying cycle
(see page 7).
FUNCTION buttons: to select the functions
available. The button corresponding to the function
selected will remain on.
TEMPERATURE knob: to set the temperature or
the cold wash cycle (see page 7).
START/STOP button: to turn the Washer-dryer on
and off.
START/RESET button: to start the programmes or
cancel any incorrect settings.
ON-OFF/DOOR LOCK Led: to find out whether the
Washer-dryer is on and if the appliance door can be
opened (see page 5).
PROGRAMME knob: to select the wash
programmes. The retractable control knob: press
the centre of the knob for it to pop out. The knob
stays still during the cycle.
Downloaded from www.Manualslib.com manuals search engine

5
GB
ServiceTroubleshootingPrecautions CareProgra es DetergentsInstallation Description
ON-OFF/DOOR LOCK led:
If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damages,
wait for the LED to flash before you open the appliance door.
 The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED indicates
there is an abnormality. Call for Technical Assistance.
Cycle phase under way:
During the wash cycle, the LEDs gradually illuminate
on to indicate the cycle phase under way:
Prewash / Wash
Rinse
Spin cycle
Drying
Note:
- during draining, the LED corresponding to the Spin
cycle phase will be turned on.
- when the drying cycle is complete, the indicator light
relative to phase will flash, to indicate that the
DRYING knob needs to be set back to the 0 setting.
Function buttons
The FUNCTION UTTONS also act like LEDS.
When a function is selected, the corresponding
button is illuminated.
If the function selected is incompatible with the
programme set, the button will flash and the
function will not be enabled.
If you set a function that is incompatible with
another function you selected previously, only the
last one selected will be enabled.
Leds
The LEDS provide important information.
This is what they can tell you:
Delay set:
If the Delay Timer function has been enabled (see
page. 7), once you have started the programme,
the LED corresponding to the delay set will begin to
flash:
As time passes, the remaining delay will be
displayed, and the corresponding LED will flash:
Once the set delay is complete, the flashing LED will
turn off and the programme set will start.
Downloaded from www.Manualslib.com manuals search engine

6
GB
Type of fabric and degree of soil Program-
mes
Wash
temp.
Detergent Fabric
softener
Cycle
length
(minutes
Description of wash cycle
Pre-
wash Wash
Cottons
Extremely soiled whites
(sheets, tablecloths, etc.) 190°C    137 Pre-wash, wash cycle, rinse cycles,
intermediate and final spin cycles
Extremely soiled whites
(sheets, tablecloths, etc.) 290°C   120 Wash cycle, rinse cycles, intermediate
and final spin cycles
Heavily soiled whites and fast
colours 360°C   105 Wash cycle, rinse cycles, intermediate and final spin cycles
Slightly soiled whites and delicate
colours (shirts, jumpers, etc.) 440°C   72 Wash cycle, rinse cycles, intermediate
and final spin cycles
Drying cycle for cotton fabrics
Synthetics
Heavily soiled fast colours
(baby linen, etc.) 560°C   77 Wash cycle, rinse cycles, anti-crease or delicate spin cycle
Fast colours (all types of slightly
soiled garments) 540°C   62 Wash cycle, rinse cycles, anti-crease or
delicate spin cycle
Heavily soiled fast colours
(baby linen, etc.) 650°C   73 Wash cycle, rinse cycles, anti-crease or
delicate spin cycle
Delicate colours (all types of
slightly soiled garments) 740°C   58 Wash cycle, rinse cycles, anti-crease or delicate spin cycle
Delicate colours (all types of
slightly soiled garments) 830°C   30 Wash cycle, rinse cycles and delicate spin cycl
Drying cycle for synthetic fabrics
Delicates
Wool 940°C   50 Wash cycle, rinse cycles and delicate
spin cycle
Very delicate fabrics
(curtains, silk, viscose, etc.) 10 30°C   45 Wash cycle, rinse cycles, anti-crease or
draining cycle
Drying cycle for delicate fabrics
PARTIAL PROGRAMMES
Delicate rinse cycle  Rinse cycles, anti-crease or draining
Delicate spin cycle Draining and delicate spin cycle
Draining Draining
Starting and Progra es
Progra e table
Notes
For the anti-crease function, please see page 8. The information contained in the table is purely indicative.
Special progra e
Daily wash 30' (programme 8 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it
only lasts 30 minutes and allows you to save on both time and energy. y setting this programme (8 at 30°C), you can
wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommen the use of liqui etergent.
Briefly: starting a progra e
1. Switch the Washer-dryer on by pressing button .
All the LEDS will light up for a few seconds and
the ON-OFF/DOOR LOCK Led will begin to flash.
2. Load your laundry into the Washer-dryer and
shut the appliance door.
3. Set the PROGRAMME knob to the programme
required.
4. Set the wash temperature (see page 7).
5. Set the drying cycle if necessary (see page 7).
6. Add the detergent and any fabric softener
(see page 8).
7. Start he programme by pressing the START/RESET
button.
To cancel it, keep the START/RESET button pressed
for at least 2 seconds.
8. When the programme is finished, the ON-OFF/
DOOR LOCK Led will flash to indicate that the
appliance door can be opened. Take out your
laundry and leave the appliance door ajar to allow
the drum to dry thoroughly. Turn the Washer-dryer
off by pressing button .
Downloaded from www.Manualslib.com manuals search engine

7
GB
Function Effect Comments Enabled with
programmes:
Delay Timer
Delays the start
of the wash by
up to 9 hours.
Press the button repeatedly until the LED corresponding to the
desired delay is turned on.
The fifth time the button is pressed, the function will be disabled.
N. .: Once you have pressed the Start/Reset button, the delay
can only be decreased if you wish to modify it.
All
Super
Wash
Allows for an
impeccable wash,
visibly whiter
than a standard
Class A wash.
This function is incompatible with the RAPID function. 1, 2, 3, 4,
5, 6, 7
Rapid
Cuts the duration
of the wash cycle
by 30%. This function is incompatible with the SUPER WASH function. 1, 2, 3, 4,
5, 6, 7
1200-600
Reduces the spin
speed.
All
programmes
except for 10
and draining.
ServiceTroubleshootingPrecautions CareProgra es DetergentsInstallation Description
Personalisations
Setting the te perature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6).
The temperature can be lowered, or even set to a cold wash ( ).
Set the drying cycle
Turn the DRYING knob to set the desired drying type.
Two options are available:
A - ased on time: From 40 minutes to 150.
B - ased on the damp level of the dry clothes:
Iron : slightly damp clothes, easy to iron.
War robe : ry clothes to put away.
Extra ry : very dry clothes, recommended for towelling
and bathrobes.
A cooling stage is foreseen at the end of the drying cycle.
If your laundry load to wash and dry is exceptionally in excess
of the maximum load foreseen (see table opposite), perform
the wash cycle, and when the programme is complete, divide up the garments and put part of them back in the
drum. Now follow the instructions provided for a dry only cycle. Repeat this procedure for the remainder of the load.
Dry only
Turn the PROGRAMME knob to one of the drying settings depending on the type of fabric, then select the
desired drying type using the DRYING knob.
Important: - A spin cycle is carried out during the drying if you have set a cotton programme and a level of
dryness (Extra dry , Wardrobe , Iron ).
- The woollen garments drying cycle should only and exclusively be run together with the selection of a specific
cycle time (150 - 100 - 60 - 40 minutes). We recommen a 60 minute rying cycle for a 1 kg loa .
If one of the three levels (Extra dry , Wardrobe , Iron ) is selected by mistake, the appliance will run a
drying cycle lasting the MAX time foreseen (150 minutes).
- For cotton loa s of less than 1 Kg, use the rying programme esigne for synthetic fabrics.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the programme set.
Fabric
type
Load type Max.
load
(kg) Extra
dry
Ward-
robe
Iron
Cotton,
Linen
Clothing of different sizes 4 130 120 110
Cotton Terry towels 4 130 120 110
Teri t al,
Cotton
Sheets, Shirts 2,5 90 80 70
Acrylics Pyjamas, socks, etc. 1656060
Nylon Slips, tights, stockings, etc. 1656060
Table of drying ti es The ata containe in the
table are purely in icative.
Downloaded from www.Manualslib.com manuals search engine

8
GB
Detergent dispenser
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your
appliance and even pollute the environment.
Open up the detergent
dispenser and pour in
the detergent and fabric
softener, as follows.
co part ent 1: Detergent for pre-wash
(powder)
co part ent 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in
immediately prior to the wash cycle start.
co part ent 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
 Do not use hand wash detergent because it may
form too much foam.
Preparing your laundry
 Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
 Empty all pockets and check for loose buttons.
 Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 5 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1 kg
How uch does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special ite s
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme
10 which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Trainers: remove any mud. They can be washed
together with jeans and other tough garments, but
not with whites.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1 kg.
Wool ark Platinu Care
As gentle as a hand wash.
Ariston sets a new standard of superior
performance that has been endorsed by
The Woolmark Company with the prestigious
Woolmark Platinum Care brand. Look for the
Woolmark Platinum Care logo on the Washer-dryer
to ensure you can safely and effectively wash wool
garments labelled as "hand wash" (M.00221):
Set programme 9 for all "Hand wash"
garments, using the appropriate detergent.
Anti-crease
This function interrupts the wash programme, and
the washing is left to soak in water before the
appliance is drained. It is enabled in programmes
5 - 6 - 7 - 10 and Delicate rinse cycle.
To conclude the cycle, press the START/RESET
button.
To run the draining cycle alone, set the knob to the
relative symbol and press the START/RESET
button.
Detergents and laundry
1
2
3
Downloaded from www.Manualslib.com manuals search engine

9
GB
Precautions and advice
ServiceTroubleshootingPrecautions CareProgra es DetergentsInstallation Description
 The Washer-dryer was designed and built in
compliance with the applicable international safety
regulations. The following information is provided for
your safety and should consequently be read carefully.
General safety
 This appliance has been designed for non-
professional, household use and its functions must
not be changed.
 This Washer-dryer should only be used by
adults and in accordance with the instructions
provided in this manual.
 Never touch the Washer-dryer when barefoot
or with wet or damp hands or feet.
 Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
 Do not open the detergent dispenser while the
appliance is in operation.
 Do not touch the drain water as it could reach
very high temperatures.
 Never force the Washer-dryer door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
 In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
 Always keep children well away from the
appliance while in operation.
 The appliance door tends to get quite hot during
the wash cycle.
 Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
 efore loading your laundry into the washing
machine, make sure the drum is empty.
 During the drying phase, the door tends to get
quite hot.
 Do not use the appliance to dry clothes that have
been washed with flammable solvents (e.g.
trichlorethylene).
 Do not use the appliance to dry foam rubber or
similar elastomers.
 Make sure that the water tap is turned on during
the drying cycles.
 This washer-dryer can only be used to dry clothes
which have been pre-washed in water.
Disposal
 Disposing of the packaging material:
observe local regulations, so the packaging can
be re-used.
 Disposing of an old Washer-dryer:
before scrapping your appliance, cut the power
supply cable and remove the appliance door.
Saving energy and respecting the
environ ent
Environ entally-friendly technology
If you only see a little water through your appliance
door, this is because thanks to the latest Ariston
technology, your Washer-dryer only needs less than
half the amount of water to get the best results: an
objective reached to respect the environment.
Saving on detergent, water,
energy and ti e
 To avoid wasting resources, the Washer-dryer
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
 The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
 Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on
energy.
 Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
 If you use your Washer-dryer from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
The Delay Timer option (see page 7) helps to
organise your wash cycles accordingly.
 If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
Downloaded from www.Manualslib.com manuals search engine

10
GB
Care and aintenance
Cutting off the water or electricity
supply
 Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
 Unplug your appliance when cleaning it and
during all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser
by raising it and pulling it
out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for your appliance door and
dru
 Always leave the appliance door ajar to prevent
unpleasant odours from forming.
Cleaning the pu p
The Washer-dryer is fitted with a self-cleaning pump
that does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into
the pre-chamber that protects the pump, situated in
the lower part of the same.
 Make sure the wash cycle has ended and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front of the
Washer-dryer (see
figure);
2. unscrew the lid
rotating it anti-
clockwise (see figure): a
little water may trickle
out. This is perfectly
normal;
3. clean the interior thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong and
a cracked hose could easily split open.
 Never use hoses that have already been used.
1
2
Downloaded from www.Manualslib.com manuals search engine

11
GB
Your Washer-dryer could fail to work. efore calling for Assistance (see page 12), make sure the problem can't
easily be solved by consulting the following list.
Troubleshooting
Proble
The Washer-dryer won't start.
The wash cycle won't start.
The Washer-dryer fails to load
water.
The Washer-dryer continuously
loads and unloads water.
The Washer-dryer does not
drain or spin.
The Washer-dryer vibrates too
uch during the spin cycle.
The Washer-dryer leaks.
The ON-OFF/DOOR LOCK Led
flashes rapidly at the sa e
ti e as at least one other LED.
There is too uch foa .
The washer-dryer does not dry.
Possible causes/Solution:
 The appliance is not plugged into the socket, or not enough to make contact.
 There has been a power failure.
 The appliance door is not shut properly.
 The button has not been pressed.
 The START/RESET button has not been pressed.
 The water tap is not turned on.
 A delayed start has been set (using the Delay Timer, see page 7).
 The water inlet hose is not connected to the tap.
 The hose is bent.
 The water tap is not turned on.
 There is a water shortage.
 The water pressure is insufficient.
 The START/RESET button has not been pressed.
 The drain hose is not fitted between 65 and 100 cm from the floor
(see page 3).
 The free end of the hose is underwater (see page 3).
 The wall drainage system doesn't have a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and call for Assistance. If the dwelling is on one of
the upper floors of a building, there may be drain trap problems causing the
Washer-dryer to load and unload water continuously. In order to avoid such
an inconvenience, special anti-drain trap valves are available in shops.
 The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 6).
 The Easy iron option is enabled: to complete the programme, press
the START/RESET button (see page 7).
 The drain hose is bent (see page 3).
 The drain duct is clogged.
 The drum was not unblocked correctly during installation (see page 2).
 The Washer-dryer is not level (see page 2).
 The Washer-dryer is closed in between furniture cabinets and
the wall (see page 2).
 The water inlet hose is not screwed on correctly (see page 2).
 The detergent dispenser is obstructed (to clean it, see page 10).
 The drain hose is not secured properly (see page 3).
 Call for Assistance because this means there is an abnormality.
 The detergent is not suitable for machine washing (it should bear the
definition "for Washing-machine" or "hand and machine wash", or the like).
 You used too much detergent.
 The appliance is not plugged into the socket, or not enough to make contact.
 There has been a power failure.
 The appliance door is not shut properly.
 A delayed start has been set (using the Delay Timer, see page 7).
 the DRYING knob is on the 0 setting.
ServiceTroubleshootingPrecautions CareProgra es DetergentsInstallation Description
Downloaded from www.Manualslib.com manuals search engine

12
GB
Before calling for Assistance:
Check whether you can solve the problem on your own (see page 11);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised servicemen.
Notify the operator of:
 the type of problem;
 the appliance model (Mod.);
 the serial number (S/N);
This information can be found on the data plate situated on the rear of the Washer-dryer.
Service
Service
195042276.01
02/2 004 - Xerox Business Services
Downloaded from www.Manualslib.com manuals search engine