Arkal 1400 1 Series User manual

A
B
IN
OUT
A
B
IN
OUT
Arkal 4" Angle Filter
Catalog No. 1400 1_ _ _ VICTAULIC CONNECTION
1400 7_ _ _ 4”ARKAL FLANGE (ASA, BSTD, DIN)
Technical Data
Inlet / outlet diam. 110 mm / 4" 4"
4" Arkal flange 4" Arkal flange
End connections (optional) 4" Victaulic 4" Victaulic
Maximum pressure 10 Bar 140 psi
Maximum flow rate 60 m3/h 265 gpm
General filtration area 1852 cm2 287 in2
Filtration volume 1774 cm3 108 in3
Length of filter 636 mm 25 1/32"
Width of filter 250 mm 9 27/32"
Distance between end connections (A) 146 mm 5 3/4"
Distance between end connections (B 187 mm 7 3/8"
Outer diam. Of filter element 170 mm 6 11/16"
Length Of filter element 347 mm 13 21/32"
Weight - victaulic connection 10.6 kg 23.3 lbs.
Weight with plastic flanges 12.6 kg 27.7 lbs.
Maximum temperature 70° C 158° F
Filtration Grades Head Loss Chart
Off-white (800 micron / 18 mesh)
Blue (400 micron / 40 mesh)
Yellow (200 micron / 80 mesh)
Red (130 micron / 120 mesh)
Black (100 micron / 140 mesh)
Green (55 micron)
Grey (20 micron)
AK 4”ANGLE 9606 71400EN 11/07

Dismantling (for cleaning)
1. Release pressure and open drain tap.
2. Open cover clamp by lifting clamp lever.
3. Pull cover from body.
4. Remove filter element.
5. Open spine tightening nut.
6. Pull cap’s telescopic extension to spread the discs.
7. Rinse with high pressure water jet.
8. To replace filter discs, dismantle spine by releasing inside clamps of spine cap.
Assembly
1. Close spine tightening nut until discs are tightly compressed.
2. Place filter element back in place.
3. Place filter cover on filter body.
4. Secure clamp on cover and close by the lever.
Installation
1. The 4" ANGLE filter may be installed horizontally or vertically.
2. A shut off valve should be installed at the filter inlet in order to close water supply for servicing.
3. A small tap with a flexible hose should be connected in front of the shut off valve for manual cleaning of the filter element.
Part List
No. Cat. No. Description Materials
1. 2501 0300 Filter cover R.PA
2. 5005 0004 Hydraulic seal EPDM
3. 5042 0040 Clamp S.S
4. 2506 0302 3"-4" Spine tightening nut PP
5. 2506 0304 3"-4" Spine cap PP
6. 2033 2_ _ _ Disc set PP
7. 5003 2220 O-ring 2-220 EPDM
8. 2502 0302 3"-4" Spine 99 PP
9. 5003 2354 2-354 O-ring EPDM
10. 5054 0212 ½" x ¼" Tap BRASS
11. 2511 0103 Gauge port nut R.PP
12. 5006 0004 Gauge port seal EPDM
2140 2_ _ _ 3"-4" Filter element 99
13. 2199 0043 3"-4" Spine 99 (w/o disc set) R.PA
14. 2242 1001 4” body complex victaulic ends
14.1 2242 7000 4” body complex with flanges
15. 5019 0112 ½" Plug
16. 2253 0425 4” Arkal flange
16.1 2510 0425 4” Ring flange R.PA
16.2 2507 0402 Cone flange POM
16.3 5005 2014 4” Gasket EPDM
Materials
R.PP- REINFORCED POLYPROPYLENE
R.PA - REINFORCED POLYAMIDE
S.S- STAINLESS STEEL
PP- POLYPROPYLENE
POM- POLYOXYMETHYLENE
16.116.3 16.2
10
11
16.3
9
1
2
3
15
16.1
8
13
6
7
5
4
12
14
16.2
14.1
16
16
AK 4”ANGLE 9606 71400EN 11/07