Arkiplot ArkiPress UHP-20M-D User manual

ArkiPress HP8E-D 40x50cm Auto Open doble plato
UHP-20M-D Manual

GY-04 Operation Instruction
1. When you turn on the heat press machine, the display shows “OFF”.
2. Press the “OK”button will show the degrees Celsius “C”. You could use the Up or
Down button to switch between degrees Celsius and degrees Fahrenheit.

3. Press “OK”button to enter TEMPERATURE setting. When the TEMP indicator
blinks, use Up/Down button to set the required temperature. (Temperature
adjustable range: 100-225 C/212-437 F)
4. Press “OK”button to enter TIME setting. When the TIME indicator blinks, use
Up/Down button to set the required time. (Time adjustable range: 0-999S)
5. After finishing above-mentioned settings, press“OK”button to enter the heating
mode. If the temperature is below 100C/212F, then the display reads “LO”(low
temperature).

6. If you need to adjust the settings during the heating mode, you could repeat step
2 to step 5 to do the adjustment.
7. When the heat platen has settled into its desired temperature, press down the
heat platen, then the timer will automatically start counting down and CD-L indicator
blinks. The timer will begin to sound once it reaches 3 seconds. The warning is meant
to prepare the user to release the handle once the time reaches 0 seconds. When
the handle is lifted, the timer will automatically sound off.
8. Long press the digital controller for 4-5 seconds, then can enter the engineering
model:
P-5: Temperature Difference Calibration Mode, calibration range is -99 to +99
P-6: Intermittent heating in advance before setting, setting range is from 1 to 20 Sec.
This function is to set the heating time and pause time after the machine enter the
constant temperature mode. The setting parameters is different according to
different size of heat platen.
P-7: Constant temperature in advance before setting, setting range is from 1 to 9
degree.
This function is to set when the machine will enter the constant temperature mode.
You could set a temperature value that you want to enter to constant temperature
before it reach the setting temperature.
For example, the setting temperature is 180℃and P-7 is 10℃, then when the
temperature reaches 170℃, it will enter the constant temperature mode, heating
and pause in cycle to avoid overheat.
P-8: Constant temperature mode, when reach the setting temperature, the machine
will stop heating for 1 seconds then will keep heating for few seconds, setting range
is from 0 to 9 Sec.
P-9: Countdown mode: “No”means when the machine work, it will count down,
“Yes”means when reach the setting temperature, the machine will enter the
countdown mode.

Maintenance
1. In order to prolong the machine service life, please add the lubrication oil on the
joints regularly .
2. Turn off the power before changing spare parts. In order to ensure the accuracy
of the parameter of GY-04 controller. please re-set the time and temperature
3. To avoid damage, please keep the heaters well when change the spare parts
Trouble Shooting For Transfer Print Quality
1. After changing heat platen, time and temperature showing become abnormal:
Solution: Reset time/temperature according to the manual
2. If the color is not as bright as photo after printing, please try below ways:
Solution: A. Adding transfer time. B. Increasing transfer temperature.
3. If the print color is too brown or the transfer paper is almost burnt:
Solution: Please reduce the setting temperature
4.If print color is different/ partial transfer effect is not good enough:
Solution: A. Increase the pressure. B. Extend the transfer time. C. Change the
sublimation paper.
5.If the machine is getting abnormal, please contact us to solve the problems.

Explosion View
No.
Part name
Qty.
No.
Part name
Qty.
1
Flat Pipe on Under frame
2
39
Cover Plate
1
2
Pillar Plate Left and Right
2
40
Heat Plate
1
3
Tapered Machine Leg
4
41
Pinboard
1
4
Square Block
4
42
GB Gross Screws Type138 M4X12-N
10
5
GB Hexagon Type 22 M8*25-N
12
43
Heat-insulating Plastic Ring
4
6
Bottom Plate
1
44
Adjusting Handle
1
7
Front Flat Pipe For Machine Frame
1
45
Adjusting Screw Rod
1
8
Square Pipe of base plate support
1
46
Adjusting Nut
1
9
Pillar Junction Plate
1
47
Gasket
1
10
Pillar Intermediate Strengthen Plate
2
48
Heat Plate
1
11
Flat Pipe
2
49
400X500
1
12
Flat Pipe
2
50
Cover for Handle
4
13
Ringent Slider
4
51
Connection Strap
2
14
GB Cross Screws Type 142 M8*25-N
6
52
Limit Switch
1
15
GB Fastener Washer SW 8
11
53
Controller Panel
1
16
GB Fastener Washer SWMC 10
24
54
Right Plate of Controller Box
1

17
Electromagnet plate
1
55
Left Plate of Controller Box
1
18
GB Fastener Nut LN M8-N
1
56
Power Cord Holder
1
19
Arm
1
57
Power Switch
1
20
Ball Bearing
8
58
Back Plate of Controller Box
1
21
Mat for Electromagnet plate
1
59
Transformer
1
22
GB Fastener Nut SNAB1 M4-N
2
60
Handwheel screw
4
23
Left and Right Handle Plate
1
61
GB-Fastener Nut Snc1 M5-N
4
24
Left and Right Handle Plate
1
62
Controller
1
25
Handle Spindle
1
63
GB Cross Screws Type135 M3X6 N
4
26
Handle Arched Plate
1
64
prat0157
1
27
Handle
1
65
Electromagnet Drive Plate
1
28
Electromagnet
1
66
Emergency Stop Switch
1
29
Alum. Arm
1
67
Relay
1
30
Post Bolt
2
68
Fixing Frame of Base Plate
1
31
Arm Bolt
2
69
Big Shake Handshandle
1
32
GB Hexagon Type 9 M10-N
8
70
Base Plate
2
33
Fixed Head for Gas Spring
1
71
Silicone Pad
2
34
Fixed Base for Gas Spring
1
72
Cushion Column of Base Plate
8
35
Round steel for Fixing Gas Spring
1
73
Reinforcing Rib of Slider Board
4
36
Round steel for Fixing Gas Spring
1
74
Chrome-plated Pole
2
37
Steel for Gas Spring Distance
2
75
Aluminium Rod
2
38
Steel for Gas Spring Distance
2
76
Anti-collision Adhesive
4