Arlec HL110 User manual

4
Arlec guarantees this product against defects of materials and workmanship for a
period of 1 year from the date of purchase provided the product is used for its
proper purpose, in accordance with Arlec’s recommendations and within such
voltage and current limits as are specified by Arlec in relation to the product.
Arlec will at its own option and cost make good, or replace this product with the
same or similar product and return it to you, or provide a credit for any product
manufactured or supplied by it, which proves to be defective within the limits set
out above provided that no repairs, alterations or modifications to the product
have been undertaken or attempted by anyone, other than Arlec or its authorized
agents. Should you wish to make a claim under this guarantee, the product and
proof of purchase must be returned pre-paid by you to the place of purchase.
This guarantee is in addition to and does not take away from any other rights and
remedies you may have under any relevant law.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
Proof of Purchase
Please retain your proof of purchase for all warranty claims.
ARLEC WARRANTY
CPIN002110
*Guarantee excludes tungsten halogen tubes
For all Sales & Warranty enquiries
Arlec Australia Pty Ltd. (A.C.N. 009 322
105).
272-274 Maroondah Highway
Chirnside Park, Victoria 3116 Australia
PO Box 181 Lilydale Victoria 3140 Australia
Phone [phone] Fax [phone]
[e-mail]
© This instruction leaflet is subject to copyright and must not be reproduced,
copied or otherwise used in any way or for any purpose without the consent in
writing of the owner, Arlec Australia Pty Ltd (A.C.N. 009 322 105).
CPIN002110
HL110 INSTRUCTIONS
500W Portable
Halogen Worklight

PORTABLE HALOGEN FLOODLIGHT (HL110)
ASSEMBLY
DO’S AND DON’TS
Extreme care should be taken when handling and operating the
Portable Halogen Floodlight HL110.
Please observe the following do’s and don’ts to ensure safe and trouble free use:
DO ensure combustible material is kept away from Floodlight.
DO use the handle to adjust the beam.
DO keep the floodlight out of reach of children when in use.
DO switch off and allow to cool for a minimum of 10 minutes before storing.
DO take extreme care in crowded or confined areas that Floodlight is not
positioned where it can be easily toppled over.
DO use the Floodlights in horizontal position (±4°). If not used in horizontal position
the tube life will be greatly reduced.
DON’T touch tube with bare hands. This could cause tube to shatter when
Floodlight is switched on.
DON’T stand Floodlight in pools of water.
DON’T handle with wet hands or operate when standing on wet surface.
DON’T position the Floodlight closer than one metre from surface to be
illuminated.
DON’T allow power cable to come into contact with front of Floodlight or housing.
DON’T touch the housing or glass while hot.
DON’T allow overhanging shrubs or foliage to come into contact with Floodlight.
DON’T place or operate the Floodlight closer than 5 metres to a swimming pool
or spa.
DON’T operate the Floodlight with the front of housing opened.
OPERATION: The Portable Halogen Floodlight HL110 is suitable for indoor or
temporary outdoor use, from any standard power point and is weatherproof to IP44.
Extreme care should be taken when handling and operating the Portable Halogen
Assemble stand and light as follows:
Attach stand (A) to floodlight / handle
assembly (B) using adjustment knob (C).
Tighten to thumb pressure, do not over
tighten.
NOTE: Arlec safety adjustment slot
prevents Floodlight from tilting too far
forward or backward. This helps avoid
accidental scorching or burning.
The tungsten halogen tube is supplied and packed separately to avoid damage.
Open the Floodlight housing by loosening the top screw. The glass front of the
housing will hinge forward and down. Ensure that Floodlight is unplugged from
wall socket. Insert the tube in the holder, ensuring that you do not touch the glass
envelope of the tube with bare hands. Use the tube wrapper to handle tube.
(Oils from the hands can cause the tube to fail or shatter).
If necessary the tube should be carefully cleaned with methylated spirit and dried
before installation. Do not attempt to adjust or force the tube holder with tools, but
carefully push the tube into the holder contacts. Reassemble the Floodlight
housing.
4°
4°
4°
4°
FITTING THE TUNGSTEN HALOGEN TUBE
A
B
C
2 3