Arlec WLED2030 User manual
WLED2030 A5_ 4 pAgE instruction mAnuAL cpin002943/2
CPIN002943/2
LUMEN
LED PORTABLE WORKLIGHT
Operating Instructions WLED2030
Important! Please read these instructions carefully before use.
Due to continuous research and development the specifications herein are subject to change without notice.
20W
PORTABLE WORKLIGHT
20W
Warranty
Arlec guarantees this product in accordance with the Australian Consumer Law.
Arlec also warrants to the original first purchaser of this product (“you”) from a retailer that this product will be free of defects in materials
and workmanship for a period of 12 months from the date of purchase; provided the product is not used other than for the purpose, or in a
manner not within the scope of the recommendations and limitations, specified by Arlec, is new and not damaged at the time of purchase,
has not been subjected to abuse, misuse, neglect or damage, has not been modified or repaired without the approval of Arlec and has not
been used for commercial purposes (“Warranty”).
If you wish to claim on the Warranty, you must, at your own expense, return the product, and provide proof of original purchase and your
name, address and telephone number, to Arlec at the address below or the retailer from whom you originally purchased the product within
12 months from the date of purchase.
Arlec will (or authorise the retailer to) assess any claim you may make on the Warranty in the above manner and if, in Arlec’s reasonable
opinion, the Warranty applies, Arlec will at its own option and expense (or authorise the retailer to) replace the product with the same or
similar product or repair the product and return it to you or refund the price you paid for the product. Arlec will bear its own expenses of
doing those things, and you must bear any other expenses of claiming on the Warranty.
The Warranty is in addition to other rights and remedies you may have under a law in relation to the product to which the Warranty relates.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or
refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Arlec Australia Pty. Ltd. ACN 009 322 105 (“Arlec”) gives the Warranty.
Arlec’s telephone number, address and email address are:
Customer Service: (03) 9982 5111
New Zealand Toll Free: 0800 003 329
Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130
Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130
Email: [email protected]
Important Notes
• Donotremovethesupportbracketfrom
thelampbody.
• Donotpinchorsharplybendthesupply
cordwhileadjustingthelamphead.
• Donotopentheworklightbody,thereare
nouserserviceablepartsinside.
• Donotimmerseinwaterorany
otherliquid.
• Donotuseabrasivecleaners,
cleanwithadampcloth.
• Ifthesuppliedexiblecordisdamaged
itmustonlybereplacedbyaservice
agentorsimilarlyqualiedpersoninorder
toavoidahazard.
High Output LED
Module Array
• 20WLEDarray
• Provideshighintensityeven
lightdistribution
• Indoor/Outdoorlightingforcontractor,
tradesman,andDIYapplications
• Cooltotouchdurablepolycarbonate/
aluminiumhousing
• Wideanglecoverageforlarge
workareas
• WeatherproofIP44rating.
Specifications
INPUT VOLTAGE 220-240Vac50Hz
WATTAGE 20W
IP CLASSIFICATION IP44
LED
Superbrightmodule
•300mA
•29-35V
•20W
•6500K
(non-replaceabletype)
PROTECTIVE
SHIELD
GlassLens
172x110x3.85mm
thick
ENCLOSURE polycarbonate/
aluminiumhousing
Holdstandhandlermly
Pushlamp
headforward
orbackwardto
desiredangle
70°
even
light
beam
WLED2030 A5_ 4 pAgE instruction mAnuAL cpin002943/2
Base
stand
Opening
adjacentto
theSupport
Bracket
opening
Fixing
knob
Introduction
TheArlecWLED2030issuitablefor
indoorandtemporaryoutdooruse.Itis
idealforcontractor,tradesmanandDIY
handymanapplications.Pleasenotethat
whenusedoutdoorsthesupplyplugand
socket-outletmustbesuitablyprotected
againstwateringress.
Assembly
Assembletheworklightasshownbelow.
1Removethexingknobwithintegralscrew
fromthebasestand,thenslidethebase
standintotheopeningadjacenttothe
supportbracket.
2Insertxingknobwithintegralscrewinto
thecaptivenutinsidebasestand,then
tightenrmly.
Tosetthetiltofthelampheadsimplyloosen
thexingknob,pushtheheadforward
orbackwardtothedesiredpositionwhile
holdingthebasestand,thentightenthexing
knob.
Note:Donotremovethesupportbracketfrom
thelampbody.Whileadjustingthelamphead
avoidpinchingorbendingofthesupplycord.
Use of Worklight
1Adjustthetiltofthelampheadbypushing
thetopofheadforwardorbackwardtothe
desiredpositionwhileholdingthestand
rmlybythehandle.
2Plugtheworklightintoapowerpoint.
3Turnonthepowertotheworklight.
PORTABLE WORKLIGHT
20W PORTABLE WORKLIGHT
20W
Other Arlec Work Light manuals
