ARMATURA OmniAC20CAPQ User manual

OmniAC20CAPQ
Quick Start Guide
Version: 1.1

1
Overview
Microphone
2.4-inch Touchscreen
Camera & Palm Collector
Doorbell Button
Card Reading
Near-infrared Flash
Speaker
Terminal Block
WD0-OUT
WD1-OUT
INWD0
INWD1
GND
485B
485A 12VIN
12VIN
12VIN
GND
GND
GND
BELL+
BELL-
AL+
AL-
AUX
GND
COM
NC
NO
SEN
BUT
12VOUT
GND
TX+
RX+
TX-
RX-

2
Installation Environment
Please refer to the following recommendations for installation.
AVOID DIRECT
SUNLIGHT
AND EXPOSURE
AVOID GLASS
REFRACTION
KEEP EFFECTIVE
DISTANCE
0.3-2.5m
KEEP DISTANCE
10ft
6.5ft
window
Recommended Palm Gestures
Note:
DO NOT KEEP
YOUR FINGERS
CLOSE
KEEP SPACES
BETWEEN
YOUR FINGERS
DO NOT KEEP
PALM OUTSIDE
COLLECTION AREA
DO NOT KEEP
YOUR FINGERS
FOLD/CURLED
KEEP EFFECTIVE
DISTANCE OF
18 to 40 cm
18 to 40cm
Make sure to keep space between your fingers.
Place your palm within 18 to 40 cm of the device.
Place your palm in the palm collection area, such that the palm is placed
parallel to the device.
1.
2.
3.

Device Installation
Fix the Backplate on the wall using wall mounting screws.
Attach the device to the Backplate.
Fasten the device to the Backplate with a security screw.
Attach the mounting template sticker to the wall, and drill holes according
to the mounting paper.
1 2
43
①
②
With Backplate:
1.
2.
3.
4.
3
59.06" / 1.5m

1.
2.
3.
4.
Fix the Back Cover on the wall using wall mounting screws.
Attach the device to the Back Cover.
Fasten the device to the Back Cover with a security screw.
Attach the mounting template sticker to the wall, and drill holes according
to the mounting paper.
With Back Cover ★:
1 2
3
①
②
4
Note: Features and parameters with mark are not available in all devices. ★
4
55.12" / 1.4m

5
Standalone Installation
Power Connection
TCP/IP
Alarm Smoke
Detector
Lock
Exit Button
Door Sensor
Reader
PC
12V
12V ± 10%, at least 1500mA.
To share the power with other devices, use an AC Adapter with higher
current ratings.
1.
2.
Recommended AC Adapter

Ethernet Connection
Click on [COMM.] > [Ethernet] > [IP Address] , input the IP address and click on [OK].
IP address: 192.168.1.130
Subnet mask: 255.255.255.0
Default IP address: 192.168.1.201
Subnet mask: 255.255.255.0
Connect the device and computer software over an Ethernet cable. As shown in
the example below:
PC
Note: In LAN, the IP addresses of the server (PC) and the device must
be in the same network segment when connecting to the software.
Wiegand Reader Connection
Note: 485A and 485B can be connected to the Barrier gate or the 485 Reader,
separately, but cannot be connected to the gate and reader at the same time.
485A
485B
WD0-OUT
WD1-OUT
INWD0
INWD1
GND
12VOUT
GND
+12V
GND
WD1
WD0
Wiegand
Reader
WD0
WD1 Access
Controller
6

7
485A
485B
WD0-OUT
WD1-OUT
INWD0
INWD1
GND
12VOUT
+12V
GND
RS485 Connection
Door Sensor, Exit Button, Auxiliary Connection
485+
485-
485 Reader
GND
COM
NC
NO
SEN
BUT
AUX
ExitButton
COM
NO
+
-
Detector
Power
Smoke
Detector
Door
Sensor

Lock Relay Connection
The system supports Normally Opened Lock and Normally Closed Lock.
The NO LOCK (normally unlocked when power-on) is connected with 'NO'
and 'COM' terminals, and the NC LOCK (normally locked when power-on) is
connected with 'NC' and 'COM' terminals. Take NC Lock as an example
below:
1)Device not sharing power with the lock 2)Device sharing power with the lock
GND
COM
NC
NO
SEN
BUT
AUX
Normally Closed Lock
DC12V
FR107
Maximum 30V 3A input.
GND
+12V
DC12V
DC12V
GND
COM
NC
NO
SEN
BUT
AUX
FR107
GND
+12V
Normally Closed Lock
Do not reverse the polarity.
Alarm Connection
BELL+
+
-
-
Alarm Power
Alarm
BELL-
AL+
AL-
+
8

9
User Registration
When there is no super administrator set in the device, click on to enter the
menu. Add a new user and set User Role to Super Admin, then the system
requests for the administrator’s verification before entering the menu. It is
recommended to register a super administrator initially for security purposes.
Click on > [ ] > [ ] to register a new user. The options in-User Mgt. New User
clude entering the user ID and Name, setting User Role, registering Palm,
Face, Card and Password, adding User Photo and Access Control Role.
L
L
L
EnrolledSuccessfully

10
Ethernet Settings
Click on > [COMM.] > [Ethernet] to set the network parameters. If the
TCP/IP communication of the device is successful, the icon will be
displayed in the upper right corner of the standby interface.
L
Access Control Setting
L
Click on > [Access Control] to enter the access control management
interface and set relevant parameters of access control.
L

Health Protection
Click on > [System] > [Health Protection] to enable mask detection.
L
When the Allow Unregistered People to Access is enabled, optionally, set
Enable Capture of Unregistered Person to save the temperature data.
11