Arnott MC-2913 User manual

1REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
Arnott®is committed to the quality of its products. If you have a question or problem with any Arnott product,
please contact Arnott by calling 800-251-8993 during normal business hours or email [e-mail].
(In the EU please call [phone] or email [e-mail]).
WARNING: DO NOT inate the air suspension system until it is installed. Ination of the air suspension system
before both ends are supported by the motorcycle’s frame and/or appropriate suspension components may result in
serious personal injury and/or damage to the air suspension system. The maximum recommended air spring ination
pressure is 200 psi.
Congratulations on your purchase of an Arnott®Motorcycle Air Suspension system. This system provides
you with the ability to maintain your bike at a constant level regardless of load, resulting in enhanced vehicle
ride, handling, and performance. We at Arnott Incorporated are proud to offer a high quality product at the
industry’s most competitive pricing. Thank you for your condence in us and our product.
Proper installation is essential to experience and appreciate the benets of this system. Please take a moment
to review these installation instructions before you begin to install these components on your motorcycle.
The removal and installation of air suspension products should only be performed by a fully qualied, ASE
Certied, professional.
It is equally important to be aware of all necessary safety measures while installing your new Air Suspension
System. This includes proper lifting and immobilizing of the motorcycle and isolation of any stored energy to
prevent personal injury or property damage.
"Elevate Your Ride"

2REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
20-10222 - INFLATION KIT
PARTS LIST
QTY PART NO. DESCRIPTION
1 21-3110 MICRO RELAY ASSEMBLY W/ HARNESS
1 21-7268 4MM AIRLINE X 6FT. ACCESSORY KIT
1 21-7715 4MM VOSS FITTING ACCESSORY KIT
1 21-7271 HARNESS CABLETIES ACCESSORY KIT
1 21-7272 SPLIT LOOM- 1 FT LENGTHS ACCESSORY KIT
1 21-2698 UNIVERSAL FUSE HOLDER ASSEMBLY KIT
1 21-10142 VICTORY CROSS COUNTRY & CROSS ROADS, PUMP ASSY.
1 11-MC-VICT1 INSTALLATION MANUAL FOR MC-2913, MC-2927
1 20-10217 VICTORY CROSS COUNTRY & CROSS ROADS, MOUNTING KIT
21-10208-B - SHOCK KIT
PARTS LIST
QTY PART NO. DESCRIPTION
1 21-9263 AIR SHOCK
BILL OF MATERIALS
MC-2913 - VICTORY CROSS COUNTRY/CROSS ROADS SUSPENSION SYSTEM
HANDLE BAR SWITCH
PARTS LIST
QTY PART NO. DESCRIPTION
1 29-9749 HANDLE BAR SWITCH, BLACK

3REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
20-10222 - INFLATION KIT
PARTS LIST
QTY PART NO. DESCRIPTION
1 21-3110 MICRO RELAY ASSEMBLY W/ HARNESS
1 21-7268 4MM AIRLINE X 6FT. ACCESSORY KIT
1 21-7715 4MM VOSS FITTING ACCESSORY KIT
1 21-7271 HARNESS CABLETIES ACCESSORY KIT
1 21-7272 SPLIT LOOM- 1 FT LENGTHS ACCESSORY KIT
1 21-2698 UNIVERSAL FUSE HOLDER ASSEMBLY KIT
1 21-10142 VICTORY CROSS COUNTRY & CROSS ROADS, PUMP ASSY.
1 11-MC-VICT1 INSTALLATION MANUAL FOR MC-2913, MC-2927
1 20-10217 VICTORY CROSS COUNTRY & CROSS ROADS, MOUNTING KIT
21-10208-B - SHOCK KIT
PARTS LIST
QTY PART NO. DESCRIPTION
1 21-9263 AIR SHOCK
BILL OF MATERIALS
MC-2927 - VICTORY CROSS COUNTRY/CROSS ROADS SUSPENSION SYSTEM
HANDLE BAR SWITCH
PARTS LIST
QTY PART NO. DESCRIPTION
1 29-9750 HANDLE BAR SWITCH, CHROME

4REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
GENERAL INFORMATION:
Reading this manual signies your agreement to the terms of the general release, waiver of liability, and hold harmless agreement, the
full text of which is available at www.arnottcycles.com.
• Avoid damage to air lines and electrical components.
• Removal and installation is only to be performed by fully qualied personnel.
CAUTION: Damage to the motorcycle and air suspension system can be incurred if work is carried out in a manner other than
specied in the instructions or in a different sequence.
To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to
disconnect your battery.
Use a solid, level surface to position the bike on a motorcycle lift and use all recommended safety techniques. Lift the
bike so the rear wheel is just slightly off the ground.
Refer to the Owner’s Manual for the bike and instructions for the motorcycle lift for all correct lifting procedures. It is also
recommended that you protect any chrome or painted surfaces that may be damaged during lifting, removal or installation
process.
Each owner or installer is unique, therefore installation of this system can be done many different ways. The mounting locations of
the compressor and ination switch are suggestions by our engineers. If proper wiring guidelines and instructions are followed,
relocation of the compressor or switch will neither affect the system operation nor void your warranty.
Adjust air shock pressure as required for desired ride quality to maximize the benets of your system. Excess pressure will result
in a rmer ride, too little pressure will allow the suspension to bottom out.
1. REMOVE BOTH SADDLE BAGS AND SIDE COVERS. (FIGURES 1, 2)
FIGURE 1 FIGURE 2
FIGURE 7

5REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
2. REMOVE THE SEAT AND THE SHOCK AIR FILL VALVE NUT. (FIGURES 3, 4)
4. WITH A TWISTING MOTION, REMOVE THE SHOCK GUARD FROM THE FRAME. (FIGURE 7, 8)
3. REMOVE THE THREE SCREWS ATTACHING THE RIGHT ELECTRICAL PANEL. TIE THE PANEL UP TO GAIN
ACCESS TO THE SHOCK AND LINKAGE BEHIND IT. (FIGURE 5,6)
FIGURE 7 FIGURE 8
FIGURE 5 FIGURE 6
FIGURE 3 FIGURE 4

6REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
5. REMOVE THE SCREW IN THE IMAGES BELOW FROM THE FRAME. (FIGURES 9, 10)
6. REMOVE THE BOLTS FROM THE LOWER SHOCK AND LINKAGE CLEVIS. (FIGURES 11, 12)
FIGURE 9 FIGURE 10
FIGURE 7
FIGURE 11 FIGURE 12

7REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
7. REMOVE THE WHITE ELECTRICAL MODULE NEAR THE SHOCK FROM THE FRAME. (FIGURES 13, 14)
8. PULL THE UPPER LINKAGE PIN FROM THE FRAME. LOWER THE LINKAGE AND REMOVE THE LINKAGE PUSH
ROD. (FIGURES 15, 16)
FIGURE 13 FIGURE 14
FIGURE 7
FIGURE 15 FIGURE 16

8REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
9. REMOVE THE SHOCK FROM THE FRAME AND REMOVE THE LINKAGE FROM THE UPPER EYELET.
(FIGURES 17, 18)
10. SCREW ONE OF THE INCLUDED VOSS FITTINGS INTO THE AIR SHOCK. PULL OUT THE WHITE PLUG AND
THEN INSERT THE INCLUDED 4MM AIR HOSE UNTIL YOU FEEL IT SEAT. REMOVE THE FITTING FROM THE
SHOCK AND CONFIRM THAT THE KEEPER IS ATTACHED TO THE HOSE. SCREW THE VOSS FITTING BACK INTO
THE SHOCK AND SNUG TIGHT WITH A 10MM WRENCH. (FIGURES 19, 20, 21, 22)
FIGURE 17 FIGURE 18
FIGURE 7
FIGURE 19 FIGURE 20
FIGURE 21 FIGURE 22

9REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
11. MOUNT THE AIR SHOCK TO THE LINKAGE IN THE ORIENTATION SHOWN BELOW. ROUTE THE AIR LINE UP
AND OVER THE SHOCK. (FIGURES 23, 24)
12. PUT THE SHOCK AND LINKAGE IN THE FRAME. ROUTE THE AIR HOSE THROUGH THE LEFT SIDE OF THE
MOTORCYCLE. ATTACH THE LINKAGE PUSH ROD TO THE LINKAGE. (FIGURES 25, 26, 27, 28)
FIGURE 23 FIGURE 24
FIGURE 7
FIGURE 25 FIGURE 26
FIGURE 27 FIGURE 28

10 REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
13. LOCATE THE LOWER SHOCK AND LINKAGE PUSH ROD CLEVIS OVER THE SWING ARM. PUSH THE UPPER
LINKAGE INTO THE FRAME AND INSERT THE PIN. INSERT THE PIN KEEPER SCREW BACK INTO THE FRAME
AND TIGHTEN. INSERT AND TIGHTEN THE SHOCK CLEVIS BOLT TO THE FACTORY RECOMMENDED TORQUE
FOLLOWED BY THE LINKAGE PUSH ROD. (FIGURES 29, 30, 31, 32)
FIGURE 7
FIGURE 31 FIGURE 32
FIGURE 29 FIGURE 30

11 REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
15. INSERT THE AIR PUMP ASSEMBLY INTO THE BATTERY BOX AND ATTACH USING THE SUPPLIED SCREWS
AND LOCK WASHERS. (FIGURES 36, 37)
FIGURE 36 FIGURE 37
14. REMOVE THE THREE PANELS SHOWN BELOW FROM THE MOTORCYCLE. (FIGURES 33, 34, 35)
FIGURE 33 FIGURE 34
FIGURE 35

12 REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
17. TRIM THE 4MM HOSE TO LENGTH. FOLLOW THE SAME PROCESS AS IN STEP #10 SCREW THE VOSS
FITTING INTO THE AIR MANIFOLD. (FIGURES 40)
FIGURE 7
16. ROUTE THE AIR LINE FROM THE SHOCK ALONG THE LOWER LEFT SIDE OF THE ENGINE TOWARD THE
FRONT OF THE MOTORCYCLE. ATTACH IT ALONG THE WAY WITH THE SUPPLIED ZIP TIES.
MAKE SURE IT IS NOT TOUCHING THE EXHAUST OR RUBBING ON ANY MOVING PARTS. (FIGURES 38, 39)
FIGURE 38 FIGURE 39
FIGURE 40

13 REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
19. FOLLOW THE WIRING DIAGRAMS IN THE BACK OF THIS MANUAL TO COMPLETE THE ELECTRICAL
CONNECTIONS.
FIGURE 7
18. REMOVE THE OE CLUTCH LEVER PERCH PINCH SCREW AND DISCARD. USING THE INCLUDED SCREW
ATTACH THE SWITCH MOUNT TO THE CLUTCH PERCH. USING THE SHORTER INCLUDED SCREW
ATTACH THE HANDLE BAR SWITCH TO THE MOUNT.
(FIGURES 41, 42, 43, 44)
FIGURE 41 FIGURE 42
FIGURE 43 FIGURE 44
The use and installation of any Arnott Air Suspension product or kit may adversely affect or void your factory warranty. It is the responsibility of the
motorcycle owner to check federal, state and local laws and ordinances before modifying or customizing his or her motorcycle. It is the exclusive
and total responsibility of the motorcycle owner to determine the suitability of this product for his or her use. The user shall assume all legal
obligations, personal injury risk and all liability duties and risk associated with the use of this product. Arnott Air Suspension products are designed
and intended for the experienced on-road motorcyclists only and intended for closed course operation. Arnott Air Suspension products and kits
are designed exclusively for OEM manufactured and equipped motorcycles with no modications. Any installation of aftermarket or customized
components may adversely affect the operation and performance of Arnott Air suspension kits and components and may void the manufacturer’s
warranty. These directions are accurate at time of publication. Arnott Inc. reserves the right to revise specications without notice.

14 REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES

15 REV 3 10/08/201811-MC-VICT1
KIT # MC-2913, MC-2927
FOR 2010-PRESENT
VICTORY
®
TOURING
SERIES
WEIGHT:
0
35-2610
KMD
4/4/08
SWITCH MOUNT
ASSEMBLY
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ARNOTT, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
ARNOTT, INC. IS
PROHIBITED.
COMMENTS:
SHEET 1 OF 1
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
DATE
NAME
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
USED ON
APPLICATION
DO NOT SCALE DRAWING
FINISH
MATERIAL
REV.
A
DWG. NO.
SIZE
SCALE: NONE
INFLATION BUTTON
DEFLATION BUTTON
SOLENOID POWER
FUSE POWER
COMPRESSOR POWER
FEMALE SPADE CONNECTOR MALE SPADE CONNECTOR
ORANGE
RED
BLACK
(TWO WIRES)
AS SHOWN IN ILLUSTRATION ABOVE;
1. CUT SWITCH WIRING TO APPROPRIATE LENGTH.
2. CRIMP THE TWO MALE SPADE CONNECTORS TO THE ORANGE WIRE AND TO THE BLACK WIRE.
3. CRIMP THE FEMALE SPADE CONNECTOR TO THE DOUBLE RED WIRE.