arpha D01 User manual
USER MANUAL
D01 Smart Lock
Please read this manual carefully before installation
Table of contents
... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .
Prepare for Installation
Installation Overview
Installation Guide
Lock Calibration
Basic Functions
App Control
Additional Functions
Specifications
FAQ
Customer Service
.....................................................
... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..
... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .
... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..
... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ...
.......................................................
... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..
... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..
02
03
04
07
07
10
16
18
18
19
Prepare for Installation
Note: Please prepare a Phillips screwdriver, a drill and 4 AA
batteries before installation.
Check your door dimensions to make sure that they fit the
following measurements:
•The door hole diameter is 54mm (2⅛")
•Backset is 60mm (2⅜") or 70mm (2¾")
•The door thickness is 35mm (1⅜") to 55mm (2 ⅛")
2⅛"
54mm
1½"
38m m
or
Backset
60mm(2⅜")or
70mm(2¾")
Door
thickness
35mm(1⅜")-
55mm(2⅛")
Installation Overview
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15 1616 17 18 19 20 21
① Front Panel
② Connection Column (M4*1.5inch) * 1
③ Front Panel Block ④ Deadbolt ⑤ Pick Jack
⑥ Connection Wire ⑦ Iron Plate
⑧ Connection Column Screw (M4*1.5inch) * 1
⑨ Back Panel ⑩ Back Panel Screw (M4*0.4inch) *1
⑪ Battery Cover ⑫ Reset Button ⑬ Back Cover
02 03
⑯ Button'Switch'
⑰ Front Panel Screw (M5 * 1.8inch/2.2inch) * 2
⑱ Lock Body Screws ⑲ Paddle
⑳ Emergency Power Port Key Cover
21
⑭ Back Panel Screw (M4*1inch) * 1 ⑮ Knob
Installation Guide
1. Install the deadbolt
a. Measure your door’s backset dimension: whether it is 2¾'' /
70 mm or 2⅜ '' / 60 mm.
If your door’s backset dimension is 2⅜ '' / 60 mm, use the provided
deadbolt to install.
If your door’s backset is 2¾'' / 70 mm, turn the faceplate 180° and
pull to extend simultaneously until the deadbolt locks in position
as the pic shows below.
b. Insert the deadbolt into the doorframe and make sure the word
“TOP” faces up as indicated on the deadbolt.
c. Screw into the doorframe with a screwdriver.
TOP
TOP
2. Install the front panel
a. Align the paddle with the center hole of the deadbolt in the
horizon direction, and insert it into the hole.
b. Route connection wire under the deadbolt.
“TOP”faceup
3. Install the iron plate
a. Route the cable through the iron plate
b. Align the holes in both plates to match the front panel with the
iron plate, then fix them with the front panel screws and
connection column screw.
04 05
Note: If the thickness of your door is 35mm (1.4inch) to 45mm
(1.7inch), please use the M5*1.8inch screws to fix it.If the
thickness is 45mm (1.7inch) to 55mm (2.1inch), please fix it with
M5*2.2inch screws.
horizondirection
Connection Column
Screw
Front Panel Screw
4. Install the back panel
a. Remove the back cover, route the connection wire through the
back panel, and straighten.
b.Turn the KNOB to the vertical position and align the pick to the
door.
c. Turn the KNOB to check the latch switch is ok.
d. Fix with the back panel screws(M4 * 0.4inch) in the battery box
and 1 back panel screw(M4*1inch).
e. Insert the connection wire interface into the back panel.
f. Install 4 AA batteries and the battery cover.
Paddle
KNOB: Vertical
Back Panel Screw
(M4 * 0.4inch)
Connection Wire
Interface
Back Cover
Back Panel Screw
(M4*1inch)
Lock Calibration
1. Reset Lock: Long press 'Reset' button for 3 seconds, back to the
factory default settings.
2. when the voice prompt 'Di' and the " " button is solid on,
turn the KNOB to the horizontal position, then the voice
'successful' appears.
3. Activate Auto-Lock Function: Take the keys with you, then
close the door. Press '7 ' and it will automatically lock when
the door is closed.
Basic Functions
1. Add administrator (The first two users are
administrators)
· Short press "reset" button or any key to wake up the keyboard,
long press ' '
· Enter the administrator pin password (6~8 digits) ended
with ' ', enter the same password again. Then the voice
"successful" appears.
· Set the 2nd administrator (pin password or fingerprint), just like
the steps above.
· When the voice says "the administrator is full", it means you've
set 2 administrator password already.
06 07
Note: Make sure to press different parts of the same finger until
the whole finger data is collected completely. The lock
keyboard '1~3' will light on when added successfully.The
improper operation will increase the input times.The
administrator password is very essential for some special
settings, please keep it in mind.
Round Head
Screws
Flat Head
Screws
2. Add user
· Short press "reset" button or any key to wake up the keyboard,
long press ' ', you will hear the voice "Please verify
administrator".
· Verify the adminstrator, the voice "Successful, please add user"
appears.
· Add user's the fingerprint (3 times), or enter pin password
(6~8 digits) ended with ' ' for 2 times. Then the voice prompts
'successful'.
3. Delete user
· Short press "reset" button or any key to wake up the keyboard,
long press ' ', you will hear the voice "Please verify
administrator".
· Verify the adminstrator, the voice "Successful, please add user"
appears.
· Long press ' ' again. Then press '1' to delete all users'
fingerprints. Press '2' to delete all users' pin passwords. Press '3'
to delete all users' data.
· Then the voice prompts 'successful'
Note: The administrator can not be removed by doing steps
above. Only when you reset the lock, the old adminstrator
can be deleted and set new administrator.
4. Change the user's password
· Wake up the keyboard and press '5 ', then you will hear
the voice "please input old password"
· Please input the old password, and input the new
password when you hear the voice "new password"
· Enter new password (6~8 digits) ended with ' ', then it's
done.
Note: The administrator password can not be changed.
5. Reset the lock
· Long press the 'reset' button for 3 seconds, the keyboard will
flash.
· Verify the administrator, then the lock will back to the factory
default settings and clear the data ( The administrator will be
removed as well)
· The original password is '1234567890', confirm with ' '
· Please calibrate the lock again and set the new adminstrator
6. Lock the door
If you're outside of the door, short press ' ' to lock the door.
If you're inside of the door, just turn the knob from vertical
direction to horizon direction.
08 09
Table of contents
