Metra Electronics Door Access Terminal Combo User manual

Door Access Terminal Combo Technical Manual

Page 2
Door Access Terminal Combo Technical Manual
Table of contents
Door Access Terminal Combo Technical Manual.................................................................................... 3
Product description............................................................................................................................. 3
Basic Parts ........................................................................................................................................... 4
Door Access Terminal Combo user interface................................................................................... 4
Door Access Terminal Combo control module ................................................................................ 4
6 pole connection cable ................................................................................................................... 4
Installation .......................................................................................................................................... 5
User interface................................................................................................................................... 5
Control module ................................................................................................................................ 6
Connections ........................................................................................................................................ 8
User interface................................................................................................................................... 8
Control module ................................................................................................................................ 8
Power supply connection................................................................................................................. 9
User interface connection.............................................................................................................. 10
Electronic door lock connection..................................................................................................... 10
Tamper sensor connection............................................................................................................. 11
Push-button connection................................................................................................................. 11
DIP switch settings ............................................................................................................................ 12
Network address ............................................................................................................................ 12
Operating indicator........................................................................................................................... 14
Signalization lights............................................................................................................................. 15
Operating parameters....................................................................................................................... 15
Setting Operational parameters - via Metra NET Network............................................................ 16
Setting Operational parameters - via serial port by PC ................................................................. 16
Maintenance ..................................................................................................................................... 16
Technical data ................................................................................................................................... 17
Appendix ........................................................................................................................................... 17

Page 3
Door Access Terminal Combo Technical Manual
Door Access Terminal Combo Technical Manual
Manufacturer:
Metra inženiring d.o.o.
IOC Trzin
Špruha 19
SI-1236 Trzin, Slovenia
phone:
fax:
web:
[phone]
[phone]
www.metra.si
System:
Metra Access Control System
Product Group:
Door Access Terminal Combo
Types:
DLCIS (ISO14443A/B, ISO 15693)
DLCLF (LF Multitag)
DLCMF (Mifare, ISO14443A/B)
Year of Construction:
2011 - 2012
Declaration of Conformity:
Metra Access Control products have been developed, designed and
manufactured in accordance with the EU directive for Electromagnetic
Compatibility (2004/108/EC).
Door Access Terminal Combo Technical Manual [rev.0-050912]
2012 Metra inženiring d.o.o.
All Rights reserved.
No part of this manual may be reproduced in any form or by any means without prior written permission of Metra inženiring d.o.o.
The contents of this manual are subject to change without notice.
All efforts have been made to ensure the accuracy of the contents of this manual, however, should any errors be detected, Metra inženiring would greatly appreciate being informed of
them. Metra inženiring d.o.o. can assume no responsibility for any errors in this manual.
Product description
Door Access Terminal Combo (DAT Combo) is designed to
form a one-way check point in Metra Access Control
Systems and Electronic Locking Systems.
In Access Control Systems a RFID media is used as a door
key. For higher security (e.g. outside door, etc.) a user
specific PIN code as an addition to RFID media can be used.
In Electronic locking systems a RFID media or a locker
number followed by a locker’s PIN code can be used as a
door key.
When access is granted device gives a single relay signal for
access mechanisms such as electric door strike, automatic
door, etc. Normally it is mounted near door where passage
control is needed.
Door Access Terminal operates on line with Metra software.
It must be connected to Metra NET Network.
Passage on Door Access Terminal Combo for particular RFID
ticket can also be externally controlled by 3rd party SW via
TCP/IP software interface.
Operating parameters are defined in the Metra software.
Event data from device is used for further analyses with this
software.

Page 4
Door Access Terminal Combo Technical Manual
Basic Parts
Door Access Terminal Combo user interface
Door Access Terminal Combo control module
6 pole connection cable
6 pole round to flat cable used to connect Door Access Terminal
user interface to the control module.
Length: 3 m

Page 5
Door Access Terminal Combo Technical Manual
Installation
User interface
STEP 1: User interface can be mounted over an electrical
box or directly to the wall.
See appendices for exact dimensions and mounting holes
positions for the user interface.
STEP 2: Thread the connection wire to the installation
point.
STEP 3: With at least 4 screws attach the metal wall mount
to the wall.
NOTE: Screws are not supplied.

Page 6
Door Access Terminal Combo Technical Manual
STEP 4: Connect the cable from the control module to the
connector on the back of the user interface device.
STEP 5: Attach the user interface to the metal wall mount
and with 2mm hex screwdriver / inbus key lock it in place.
Rotate the screws counter clockwise.
NOTE: Remove the protective film from the foil.
Control module
STEP 1: Control module can be mounted over an electrical
box or directly to the wall.
See appendices for exact dimensions and mounting holes
positions for the control module.

Page 7
Door Access Terminal Combo Technical Manual
STEP 2: Thread the wires (power, network, door lock, etc.)
to the installation point.
NOTE: Example on the photo shows wires for Metra NET
Network, power, connection cable for user interface and
electronic door lock.
STEP 3: Attach the control module to the surface.
If mounted over an electrical box use the hole on the side
to wire cables thru it.
STEP 4: Connect the cables to the control module. For
details see next chapter. Attach the front with 4 supplied
screws.
STEP 5: With two supplied screws attach the front cover.

Page 8
Door Access Terminal Combo Technical Manual
Connections
User interface
#
description
1
User interface –control module communication
Control module
#
description
#
description
1
Metra NET Network
8
Not Used

Page 9
Door Access Terminal Combo Technical Manual
2
Power 12V DC
9
Not Used
3
Door Lock / Tamper sensor / Push-button
10
Extension Relay Module (I2C bus)
4
Not Used
11
User interface
5
Not Used
12
Serial RS-232
6
Not Used
13
Metra NET Network
7
BDM Loader
14
Metra NET Network
Power supply connection
Regulated DC power supply is required for proper operation. See chapter “Technical data” for power
requirements.
Connect 12V DC regulated power supply to designated
terminals on the Control Module’s integrated Network
Splitter. The terminals are marked as +12V for positive
connection and GND for ground connection.
WARNING
Mind the polarity! Wrong polarity could result in
irreparable damage to the device.
Respect power requirements data! Using unsuitable
power supply could result in damage to the power
supply and to the device.
Metra NET Network connection
The Metra NET Network connection provides for operational functionality of the Door Access
Terminal Combo.
Different devices in parallel can be connected to the Metra Network Controller by a single unshielded
twisted pair (UTP) cable. Total length of the twisted pair cable is limited to 1 km. One Network Line
Terminator must be connected at the far end of the network cable. See also “Metra NET Network –
Installation Manual” for different wiring schemes.
Connect the UTP Metra NET network cable to one of the
designated terminals on the Control Module’s integrated
Network Splitter. The terminals are marked “RJ45“.
NOTE 
Do not confuse Metra NET Network connection with
computer LAN network.

Page 10
Door Access Terminal Combo Technical Manual
User interface connection
CONTROL MODULE
Connect the connection cable to the terminal marked
“READER”.
USER INTERFACE
Connect the connection cable to the terminal marked
“READER IN”.
Electronic door lock connection
Set the relay output jumpers on the device or on the relay module according your electronic door
lock.
Connect the electronic door lock to the terminals marked “RELE” on the control module.
WARNING 
Mind the power polarity if one of the options with DC output is selected –see corresponding
schematics. Wrong polarity could result in irreparable damage to the device.
WARNING 
Mind the electronic door lock power consumption. 12 V
DC door lock with max 0.5 A current consumption can be
connected directly to the device. Use additional relay
module for electronic door locks with higher current
consumption.