Arrow Storage Products RMGRA86 Instructions for use

Gloves must be worn
at all times to reduce
risk of injury!
Owner’s Manual
& Assembly Guide
731470821
BUILDING DIMENSIONS
* See Inside for Detailed Safety Information.
Size rounded off to the nearest foot For proper base construction see page 12
†
Nominal Size
8’ x 6’
EN-01JT
Model No. RMGRA86
†
Base
Size
Exterior Dimensions
(Roof Edge to Roof Edge)
Width Depth Height
Interior Dimensions
(Wall to Wall)
Width Depth Height
Door
Opening
Width Height
Approx.
Size
Storage
Area
8’ x 6’ 43 Sq. Ft. 255 Cu. Ft. 99 3/4” 71 1/4” 74 7/8” 94 3/4” 66” 73 5/8” 43 1/2” 65”
2,4 m x 1,8 m 4,0 m27,2 m3253,4 cm 181,0 cm 190,2 cm 240,7 cm 167,6 cm 187,0 cm 110,5 cm 165,1 cm
†
97 1/2” x 68 3/4”
247,7 cm x 174,6 cm
ShelterLogic.com
/
product-registration
Register • Enregistrer • Regístrate
Steel ShedSteel Shed

3
• Keep children and pets away from the worksite during construction and until the building is completely assembled. This will
help avoid distractions and any accidents which may occur.
EN-04HN
• Care must be taken when handling various pieces of your building since many contain sharp edges.
CAUTION
• Do NOT attempt to assemble your building before double checking that you have all the parts indicated in the parts lists.
Any building left partially assembled may be seriously damaged by even light winds.
• Do NOT attempt to assemble your building on a windy day. The large panels can catch the wind like a “sail”, making
construction diffi cult and unsafe.
• NEVER concentrate your weight on the roof of the building.
Watch the Weather Closely
• Before assembling any parts, your base should be constructed and an anchoring system should be ready to use.
Your building MUST be anchored to prevent wind damage.

4
EN-05HN
• The best location is a level area with good drainage.
ASSEMBLY
• Allow enough space outside the building to be able to access the roof with a ladder.
• Use Teamwork: Two or more people are required to assemble your building.
CARE & MAINTENANCE
• DO NOT use power washing to clean your shed.
• Combustibles and corrosives must be stored in air tight containers designed for chemical and/or combustible storage.
Corrosive chemicals such as fertilizers, pesticides and herbicides should be cleaned off the interior and exterior surfaces
immediately. Rust caused by chemical damage is not covered by the warranty.
Rust protection precautions
• Avoid nicking or scraping the coating surface, inside and out.
• Keep roof, base perimeter and door free of debris.
• Touch up scrapes or nicks and any area of visible rust as soon as possible.

5
HARDWARE LIST ARG EN-05HY
The fasteners used in each step are shown actual size at the top of each page. If you are unsure which
fastener to use, hold it up to the picture and use the one that matches.
165103 Hex Nut (#8-32) 102
Key
No. Part No. Part
Description Qty. Part Views
265923 Small Bolt (#8-32 x 3/8) (10 mm) 102
365004 Small Screw (#8AB x 5/16) (8 mm) 280
465900 Black Screw (#10B x 1/2) (13 mm) 8
565109 Acorn Nut (#8-32) 6
If you fi nd that a part is missing, include the model number of your building and contact the retailer where
you purchased your shed.

6
HARDWARE LIST EN-06HY
14 6228 Track Support 2
15 67293 Weather Stripping 1
16 30028 Nameplate 1
13 7916 Roof Beam Bracket 4
666045 Handle 2
767468 Peak Cap 2
866769 Door Slide 4
966646 Washer Sheet 8
10 66382 Lower Door Guide 4
11 66183L Left Roof Trim Cap 2
12 66183R Right Roof Trim Cap 2
Key
No. Part No. Part
Description Qty. Part Views
17 66775 Plug (Door Jamb Color/Clear) 2
18 66775 Plug (Door Color) 2

6
7
19 8946 Side Floor Frame 2
21 8941 Ramp 1
22
8471 Corner Panel 2
23
9382 2
24
25 6627 Wall Panel 6
26 10535 2
28
8476 Side Wall Angle 3
30
11486 Rear Wall Angle 2
31
20 11481 Rear Floor Frame 2
27 11484 Rear Wall Channel 2
EN-07JT
PARTS LIST
Key
No. Part No. Part
Description Qty. Part Views
9379 Front Floor Frame 2
Wall Panel
9920 Side Wall Channel 2
29
32 9370 2
Door Jamb
Front Corner Panel
80247 2
Door Panel

6
8
38 8474 Roof Beam 3
39 8466 Right Roof Panel 2
40 8467 Left Roof Panel 2
41 7875 Roof Panel 4
42 8482 Roof Trim 2
43 8461 Ridge Cap 1
35 6658 Gable Brace 2
36 7906 Right Gable 2
37 7907 Left Gable 2
EN-08JT
34 9378 2
PARTS LIST
Door Track
33 6617 Door Track Splice 1
44 6300 Vertical Door Channel 2
Key
No. Part No. Part
Description Qty. Part Views

6
9
EN-09aHY
PARTS LIST
Key
No.
Part No. Part
Description Qty. Part Views
45
46
10498 Horizontal Door Brace 4
69836 4 Edge Trim(Purple)

6
10
10bHY
ASSEMBLY BY KEY NO. PIÈCES PAR N° DE REPÈRE
MONTAJE POR N.º DE REFERENCIA
27
25
22
25
28
19
19
21
24
24
25 26
30
31
20
20
22
25
25
2526
27
28
32
32
30
33
34
MONTAGE NACH LFD. NR.
31
34
23
23

6
11
EN-11aHY
40
38
37
44
36
35
36
37 35
38
45
13
40
39
41
42
42
41
29
44
45
ASSEMBLY BY KEY NO.
38
41
39
30
13
13
13
41
43
29
45
45
46
46
46
46

6
12
ARG EN-12HY
CONSTRUCTING A FOUNDATION
Wood Platform Concrete Slab
16"/24"
40,6 cm/61,0 cm
97 1/2”
247,7 cm
68 3/4"
174,6 cm
97 1/2"
247,7 cm
68 3/4"
174,6 cm
*IMPORTANT *
The base MUST be fl at and level to provide adequate support for your building, otherwise the PRE-DRILLED HOLES WILL
NOT ALIGN AND IT CANNOT BE ASSEMBLED.
OPTION 1: Build directly on the ground
OPTION 2: Wood Platform
NOTE: Pressure Treated Lumber must NOT be used where it will make contact with your storage building. The properties of Pressure
Treated Lumber will cause accelerated corrosion. If Pressure Treated Lumber comes in contact with your storage building your
warranty will be voided. The platform should be level and fl at (free of bumps, ridges, etc.) to provide good support for the building.
The necessary materials may be obtained from your local lumber yard.
OPTION 3: Concrete Slab
The slab should be at least 4" (10,2 cm) thick.

13
11481
95 7/8” 243,5 cm
11 7/8” 30,2 cm
EN-14HY
1: FLOOR FRAME
Overlap Length Finished Length
11481 2
11481
9379 2
65923 65103 465004 8
65923 65103
65004
65923
65103
9379
8941
9379
8941 1
Finished Length
95 7/8” 243,5 cm
Front

12
EN-15HY
14
8946
1: FLOOR FRAME
65004 811481+11481 1(2)9379+8941 18946 2
8946
11481
11481
9379
8941
NOTES:
Do NOT fasten your Floor Frames to your
Base at this time. You will anchor your
building after it is erected.
The Floor Frame must be BOTH square AND
level or the holes will not line up properly.
Measure diagonally from corner to corner.
When diagonal measurements are equal,
the Frame is square.
X4
65004
9379
8946
11481
9379
8946
X2
65923 65103 2
65103
65923

15
EN-16HY
94 5/8” (240,3 cm)
Finished Length
11486
2: PRE-ASSEMBLY
65923 65103 211486 211484 2
65923
65103
11486
11484
65923
65103
11484
94 5/8” (240,3 cm)
Finished Length

16
EN-17HY
2: PRE-ASSEMBLY
8474 18476 1 65004 10
8474
8476
8474
8476
65004

17
EN-18HY
2: PRE-ASSEMBLY
9378
65004 49378 26617 1
Painted Part
9378
6617
94 5/8” (240,3 cm)
Finished Length
CORRECT INCORRECT
Long Leg
on top.
Door Slide
END VIEW
65004
66769
To remove or install Door Slides:
• Remove Doors from Slides and set aside.
• Using pliers, bend down a corner of the Door Track.
• Remove or install Door Slides.
• Carefully bend the corner back into position.
Slides should be installed in Door Track prior to installation. However, if this step is overlooked
or if the Slides need to be removed for maintenance, the following procedure may be used.
66769 4

18
EN-19JT
3: CORNER PANELS
65004 66646 48471 2
6627 2
65923 66646 65103 2
6627 8471
65004
66646
65923
65103
66646
6627 8471
65004
66646
65923
65103
66646

19
EN-20JT
3: CORNER PANELS
65004 66646 16 9382 28471+6627 2
65004
66646
9382
8471
6627
Front
6627
9382
8471

20
EN-21HY
8476
8476
4: WALL ANGLE
65004 66646 16 8476 2
11486+11486
65004
66646
Front
Short Leg on Bottom.
Opening Faces In.
Long Leg on Top.
(2)9378+6617 1 11486+11486 1
9378
9378
6617
9378