Arrow Revolution User manual

P/N V2-51-INST-QUK Rev A
An ASSA ABLOY Group brand
Detail B
Directions
Components
Quick Start Instructions
Installation Instructions
Door Marker
Outside Escutcheon
Inside Escutcheon Assembly:
• Inside Mounting Plate
• Inside Escutcheon
• Battery Cover
4 AA Alkaline Batteries
Bolt
Strike Plate
Screw Pack (7 screws)
2 Keys
For Technical Assistance call Arrow:
1-800-839-3157
1. Install bolt in door.
NOTE: The bolt must be in a retracted position
when installing the lockset.
Attach with two (2) M4 x 25.4mm screws
supplied.
2. Install strike on the door frame.
3. Route the cable through 2-1/8" diameter hole.
NOTE: Cable must go under bolt and through.
See Detail A.
4. Insert outside escutcheon while routing cable
through inside mounting plate’s 1/2" hole; insert
mounting plate “tongue” into bottom slot of
outside escutcheon.
5. Secure inside mounting plate to outside
escutcheon using two (2) M6 x 59.5mm
pan head machine screws. Do not over-tighten.
6. Attach cable connector to inside escutcheon
circuit board (See Detail B above). Press
firmly with thumbs so that back edge (wires) of
connector lines up with arrows on PCB.
CAUTION:
Use care when assembling to ensure that cable
lies against the back recessed area of the inside
escutcheon.
Position and bend the cable, using the harness
clip as shown in Detail B to prevent binding
when installing the escutcheon over the mounting
plate.
7. Slide inside escutcheon over mounting plate.
8. Install and secure using (3) M4 x 8mm pan
head screws through the battery housing into the
mounting plate.
9. Insert four (4) AA alkaline batteries. The lock
responds, “Welcome to the Arrow Revolution.”
Note: Refer to programming instructions prior to
completion of step 10.
10. Install battery cover and tighten Phillips
head screw.
Inside Mounting Plate Inside Escutcheon
(3) M4 x 8mm
[8-32 x 5/16"]
Pan Head Screws
(2) M6 x 59.5mm
[15/64 x 2-11/32"]
Pan Head Machine Screws
Outside Escutcheon Battery Cover
5
7
8
10
Cable
4
6
See Detail B
9
3
Detail A
Inside Mounting Plate
(2) M4 x 25.4mm
[8-32 x 1"]
Flat Head
Combination Screws
(2) M4 x 25.4mm
[8-32 x 1"]
Flat Head
Combination Screws
1
2
Tools Needed
Phillips #2 screw driver
2-1/8" (54mm) hole saw
1" (26mm) boring bit
7/64" (2.5mm) drill bit
Chisel & hammer An ASSA ABLOY Group brand
P/N LT-503201 Rev A
Touchscreen Deadbolt Quickstart Guide For more information go to: www.arrowlock.com
Harness Clip
™

An ASSA ABLOY Group brand
P/N LT-503201 Rev A
Touchscreen Deadbolt Quickstart Guide
M
Register
M
Master PIN Setting
Register User PIN
Delete
1 2 3 4 User Number (UN)
1~25
5
Complete
Continue
Complete
Continue
U
Enable
Disable
High
Low
Silent
English
Spanish
French
Enable
Disable
Auto Relock
Volume
Language
All Code Lock-Out
Programming
• For proper security, the Master
PIN code* must be changed
prior to programming the lock.
• PIN codes can be 4 to 8
digits in length.
• The key is used to enter or
accept an entry, and also to
conclude a programming
session.
• The key is used either to
enter or to continue additional
steps in a programming
sequence.
*The factory default Master
PIN code is: 1 2 3 4 5 6 7 8.
Features
Open Door With PIN Code
1. Touch the screen with
the back of your hand
or fingers to activate.
2. Enter PIN code.
3. Touch the
key to confirm
the selection.
4. Unlock.
1. Touch the screen with
the back of your hand
or fingers to activate .
2. Enter the 4-8 digit Master
PIN code* followed by
the key.
Lock Response: “Menu
mode, enter number, press
the key to continue.”
3. Enter digit corresponding
to the function to be
performed followed by
the key.
Follow the voice
commands.
4. Press the key to
complete the process
and conclude the
programming session.
For Technical Assistance call Arrow:
1-800-839-3157
™
For more information go to: www.arrowlock.com
*Default Master Pin Code must be changed
prior to any programming of lock.