Arrow SD 600eval Instructions for use

SD 600eval
Hardware User Manual
Version 1.0 May 2016
Powered By:
Downloaded from Arrow.com.

2/30
Table of Contents
1. Introduction.............................................................................................................................................................. 5
2. Change History ......................................................................................................................................................... 6
3. What’s in the Box ..................................................................................................................................................... 6
4. Board Overview ........................................................................................................................................................ 7
4.1 Key Components..................................................................................................................................................... 7
4.2 System Block Diagram ............................................................................................................................................ 8
5. Getting Started ......................................................................................................................................................... 8
5.1 Prerequisites........................................................................................................................................................... 8
5.2 Starting the Board for the First time ...................................................................................................................... 9
6. Component Details................................................................................................................................................... 9
6.1 Processor ................................................................................................................................................................ 9
6.2 PMIC ....................................................................................................................................................................... 9
6.3 Memory (DRAM) .................................................................................................................................................... 9
6.4 Storage.................................................................................................................................................................... 9
6.4.1 eMMC .............................................................................................................................................................. 9
6.4.2 Micro SDHC...................................................................................................................................................... 9
6.4.3 Boot Configuration ........................................................................................................................................ 10
6.5 Networking ........................................................................................................................................................... 11
6.5.1 WiFi/Bluetooth LE.......................................................................................................................................... 11
6.5.2 Ethernet......................................................................................................................................................... 12
6.6 Display Interface................................................................................................................................................... 12
6.6.2 MIPI-DSI ......................................................................................................................................................... 13
6.7 Camera Interface .................................................................................................................................................. 13
6.8 USB Ports .............................................................................................................................................................. 13
6.9 Audio .................................................................................................................................................................... 15
6.10 DC Power ............................................................................................................................................................ 15
6.11 Power Measurement.......................................................................................................................................... 15
6.12 External Fan Connection..................................................................................................................................... 16
6.13 UART ................................................................................................................................................................... 16
6.14 Buttons ............................................................................................................................................................... 16
6.14.1 Power Button............................................................................................................................................... 16
Downloaded from Arrow.com.Downloaded from Arrow.com.

3/30
6.14.2 Reset Button................................................................................................................................................ 16
6.15 LED Indicators..................................................................................................................................................... 16
6.16 Additional Functionality ..................................................................................................................................... 17
6.16.1 GPS............................................................................................................................................................... 17
6.16.2 SATA............................................................................................................................................................. 17
6.16.3 Magnetometer, Gyroscope & Accelerometer Interface ............................................................................. 18
6.16.4 JTAG............................................................................................................................................................. 19
7. Expansion Connectors ............................................................................................................................................ 20
7.1 Low Speed Expansion Connector ......................................................................................................................... 20
7.1.1 UART {0/1} ..................................................................................................................................................... 20
7.1.2 I2C {0/1}......................................................................................................................................................... 20
7.1.3 GPIO {A-L} ...................................................................................................................................................... 21
7.1.4 SPI0 ................................................................................................................................................................ 21
7.1.5 PCM/I2S ......................................................................................................................................................... 21
7.1.6 Power and Reset............................................................................................................................................ 21
7.1.7 Power Supplies .............................................................................................................................................. 21
7.2 High Speed Expansion Connector......................................................................................................................... 22
7.2.1 MIPI-DSI0 ....................................................................................................................................................... 23
7.2.2 MIPI-CSI {0/1} ................................................................................................................................................ 23
7.2.3 I2C {2/3}......................................................................................................................................................... 23
7.2.4 HSIC................................................................................................................................................................ 23
7.2.5 Reserved ........................................................................................................................................................ 23
7.2.6 SD/SPI ............................................................................................................................................................ 23
7.2.7 Clocks............................................................................................................................................................. 23
7.2.7 USB ................................................................................................................................................................ 23
7.3 Audio Expansion Connector ................................................................................................................................. 24
7.3.1 40-Pin Audio Expansion Connector ............................................................................................................... 24
7.3.2 16-Pin Audio Expansion Connector ........................................................................................................ 25
8. Power Management Overview............................................................................................................................... 26
8.1 Block Diagram....................................................................................................................................................... 26
8.2 DC Power Input..................................................................................................................................................... 26
8.3 Power Source Selection and Sequencing ............................................................................................................. 27
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

4/30
8.4 Power Measurements .......................................................................................................................................... 29
9. Mechanical specification ........................................................................................................................................ 30
Board Dimensions................................................................................................................................................... 30
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

5/30
1. Introduction
The SD 600eval board is a 96Boards Customer Edition compliant board based on Qualcomm® Snapdragon 600 series of SoC.
The following table lists its key features:
Processor
Qualcomm 600 APQ8064 PoP (839BNSP)
4 Krait uP cores (up to 1.7 GHz), plus 1 QDSP6 core (to 500 MHz)
Adreno 320 3D Graphics at 400 MHz / 325 MHz (turbo/ nominal) with support for
OpenGL ES 1.x, 2.0, 3.0; Direct3D Dx9.x; C2D for 2D composition; OpenCL 1.1 embedded profile
Memory/
Storage
2GB LPDDR2 533MHz
16GB eMMC on board storage
Video
1080p HD video
Camera Support
One 4-lane MIPI camera serial interface (CSI), one 2-lane MIPI CSI
Audio
PCM/AAC+/MP3/WMA, ECNS, Audio+ post-processing (optional)
Connectivity
WCN3680B integrates 3 technologies into single device
-Dual-band 2.4 GHz and 5 GHz WLAN compliant with the IEEE 802.11a/b/g/n/ac
specification
-Bluetooth (BT) compliant with 4.x + BR/EDR + BLE
Two Standard USB 2.0 Type A (Host mode only)
One OTG USB 2.0 via Micro AB
GPS/GLONASS
PCIe to Ethernet via AR8151
External GPS antenna (default) as well On-board Antenna (optional)
On-board as well as external BT and WLAN antenna
HDMI
I/O Interfaces
40 pin low speed expansion connector:
+1.8V, +5V, SYS_DCIN, GND, UART x2, I2C x2, SPI, PCM, PWM, GPIO x12
60 pin high speed expansion connector:
SDIO, 4L-MIPI_DSI, 4L+2L MIPI_CSI, I2C x2, USB2.0, HSIC
16-pin and 40-pin audio expansion connector:
Stereo Headset/Line-out, Speaker, Analog/Digital Mics.
External
Storage
Micro SD card slot
SATA Hard Drive connector
User Interface
Power/Reset
User configurable Switch
1 Wi-Fi activity LED (Yellow)
1 BT activity LED (Blue)
4 User LEDs (Green)
OS-support
Android
Linux
Version depends on current release
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

6/30
Power,
Mechanical and
Environmental
Power: +6.5V to +18V
Dimensions: 100mm x 85mm meeting 96Boards™ Consumer Edition Extended Dimensions
specifications
Operating Temp: 0°C to +50°C
RoHS and REACH compliant
2. Change History
Version
Changed By
Description of Changes
1.0
eInfochips
Initial version
3. What’s in the Box
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

7/30
4. Board Overview
4.1 Key Components
1
(J3) Ethernet Connector
2
(J1) SATA Connector
3
(J2) Power Jack
4
(SW1)User Configurable SW
5
(SW2) Soft Power Button
6
(SW3) Reset Button
7
(J4) 40 Pin Audio Expansion
Connector
8
RTC Battery Connector
9
(J16) External Battery Connector
10
(J5) Low Speed Expansion Connector
11
(J6) 16 Pin Audio Expansion
Connector
12
(U6) GPS
13
Bluetooth / WLAN Antenna
14
(U10) Bluetooth / WLAN
15
(U8) APQ8064 Processor
16
(U9) Power Management PMIC
17
(J9) High Speed Expansion Connector
18
(J10) Micro SD Card Socket
19
(J13) HDMI Type A Port
20
(J14) Micro USB Type AB Connector
21
Bluetooth / WLAN LED’s
22
(J11) USB Host 1 Connector
23
User LED’s 0-3
24
(J12) USB Host 2 Connector
25
(U26) eMMC
26
(SW5) Boot Switches
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

8/30
4.2 System Block Diagram
5. Getting Started
5.1 Prerequisites
Before you power up your SD 600eval board for the first time, you will need the following:
•SD 600eval board
•A 96Boards CE specification compliant power supply (sold separately by Arrow)
•An HDMI Monitor that supports resolution of 1080P/30Hz
•HDMI-HDMI cable to connect the board with Monitor.
•Computer keyboard with USB interface.
•Computer mouse with USB interface.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

9/30
5.2 Starting the Board for the First time
For starting the board for the first time, follow these simple steps:
Step 1. Connect the HDMI cable to the SD 600eval HDMI connector (marked J13) and to the HDMI Monitor.
Step 2. Connect the keyboard to the board’s USB connector marked J11 and the mouse to the USB connector marked J12.
(Connection can be done in any order)
Step 3. Ensure that the boot switches are set to ‘0000’, all in OFF position.
Step 4. Connect the power supply to power connector J2.
Once user plugs the power supply into a power outlet the board will start the booting process Android/Linux boot up appears on
Display.
6. Component Details
6.1 Processor
Qualcomm 600 APQ8064 PoP (839BNSP)
The Qualcomm Snapdragon 600 APQ8064 (PoP) is a 4 Krait uP cores (up to 1.7 GHz), plus 1 QDSP6 core (to 500 MHz)
Adreno 320 3D Graphics at 400 MHz / 325 MHz (turbo/ nominal) with support for OpenGL ES 1.x, 2.0, 3.0; Direct3D Dx9.x; C2D
for 2D composition; OpenCL 1.1 embedded profile (for GPGPU)
6.2 PMIC
SD 600eval uses PMM8920 for its power management requirement. PMM8920 integrates two power management die into a
single package. PMM8920 has 9 switching regulators, 22 LDO’s & 9 LVS (Low Voltage Switches) driver ports. PMM8920 provides
power to different rails of processor as well peripherals on board. PMM8920 maintains the power sequence for APQ8064
6.3 Memory (DRAM)
The SD 600eval uses Package-on-Package (POP) high-speed 2 GB LPDDR2 memory. The LPDDR2 is a 32bit width bus memory
device mounted on APQ8064 with POP/Bare die. The maximum LPDDR2 clock is 533 MHz.
6.4 Storage
6.4.1 eMMC
SD 600eval has onboard 16GB eMMC nand flash and is the default boot location. eMMC is 8-bit implementation, interfaced
with SDC1 port of APQ8064 supporting MMC 4.5 specifications.
6.4.2 Micro SDHC
The 96Boards CE specification calls for a micro SDHC socket to be present on the board. The micro SDHC socket (J10) is placed
on the bottom left corner of the SD 600eval board and is routed directly to SDC3 port of APQ8064.The Micro SD slot is a push-
push type with a dedicated support for card detect signal. SDIO interface implemented for SD card has 4 data lines, one
command, clock and card detect signals.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

10/30
6.4.3 Boot Configuration
For boot mode configuration on SD 600eval board, a 4 position SPST dip switch (SW5_SPST1) is located at the bottom side of the
SD 600eval board.
CONFIG switch in ON position indicates a Logic 1 level
Boot Selection table is shown below:
CONFIG_0
(Position-1)
CONFIG_1
(Position-2)
Function
1
1
EMERGENCY BOOT (SDC3 FOLLOWED BY USB HS)
0
1
SDC3 FOLLOWED BY SDC1 (eMMC)
1
0
SDC3 FOLLOWED BY SDC2 (Invalid)
0
0
SDC1 (eMMC) DEFAULT
Fast and secure boot selection
CONFIG_6
(Position-3)
Function
1
SECURITY BOOT
0
FAST BOOT
Forcefully entering SD 600eval board in Fast boot mode
FORCE_USB_BOOT
(Position-4)
Function
1
SDC3 FOLLOWED BY SDC1 (eMMC)
0
NO OPERATION
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

11/30
Above figure shows all the switches are in OFF (Logic 0 level) position.
6.5 Networking
6.5.1 WiFi/Bluetooth LE
The 96Boards CE specification calls for a WiFi (minimally 802.11g/n) and Bluetooth 4.0 (Bluetooth Low Energy) to be present on
board.
The SD 600eval board deployed Qualcomm’s RF chip WCN3680B (U10) solution that integrates three different wireless
connectivity technologies into a single device, the interfaces are:
•Dual-band 2.4 GHz and 5 GHz wireless local area network (WLAN) compliant with the IEEE 802.11a/b/g/n/ac
specification
•Bluetooth (BT) compliant with the BT specification version 4.0 BLE; ANT+ support
•FM radio is supported by WCN3680; this feature is not tested for SD 600eval Board
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

12/30
6.5.2 Ethernet
The 96Boards CE specification allows for optional Ethernet interface on board.
The APQ8064 processor is interfaced with Atheros AR8151 PCIe to Gigabit Ethernet controller for Ethernet connectivity on SD
600eval.
6.6 Display Interface
6.6.1 HDMI
The 96Boards CE specification calls for HDMI port to be present on board.
The HDMI signals of APQ8064 are routed to HDMI connector (J13). APQ8064 supports following HDMI features:
•Hot-plug detection
•Consumer electronics control (CEC) messages
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

13/30
6.6.2 MIPI-DSI
The 96Boards CE specification calls for MIPI-DSI implementation via the High Speed Expansion Connector.
The SD 600eval implemented a four-lane MIPI_DSI interface meeting this requirement. More information about this
implementation can be available in chapter 7.2 High speed expansion connector.
6.7 Camera Interface
The 96Boards CE specification calls for two camera interfaces via High Speed Expansion Connector.
The SD 600eval implements two camera interfaces, one with a four-lane MIPI_CSI (CSI0 port) and other with two-lane MIPI_CSI
(CSI1 port) of APQ8064. More information about this implementation can be available in chapter 7.2 High speed expansion
connector.
6.8 USB Ports
The 96Boards CE specification requires two USB 2.0 Host ports, one Micro USB 2.0 slave port to be present on board and one
USB Host port to be provided on high speed expansion connector.
The APQ8064 supports two USB 2.0 host interface, one USB OTG interface and one HSIC interface. One USB host Interface and
HSIC interface of APQ8064 is connected to high speed expansion connector. The 2nd USB Host interface is connected to on-
board USB Hub, which supports 3 downstream ports. Two downstream USB ports of USB Hub are available at Type A connector
J12 (Host1) and J11 (Host2). USB OTG port is provided at USB Micro AB connector J14 of SD 600eval board. The USB host
controller supports full speed (12Mbps) mode, high speed (480Mbps) mode and Low Speed (1.2Mbps) mode.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

14/30
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

15/30
6.9 Audio
The 96Boards CE specification calls for a minimum of single channel audio through two interfaces either via Bluetooth 4.0 or audio
output at HDMI/MHL/Display Port.
96Boards also requires I2S/PCM audio channel to be provided on the low speed expansion interface.
The SD 600eval board meets this requirement. For additional audio functionality, APQ8064 is interfaced with audio codec
WCD9310 via SLIMBUS. WCD9310 provide 6 analog differential mics, 2 digital mics, 5 speaker outs and one headset (headphone
out and single ended mic input) signals, routed to Audio Expansion connector (J4 & J6). The details of connector J4 & J6 are
mentioned in section 7.3 Audio Expansion Connector
6.10 DC Power
The 96Boards CE specification calls for power to be provided to the board in one of the following ways:
•An 8V to 18V power from a dedicated DC jack
•An 8V to 18V power from the SYS_DCIN pins on the Low Speed Expansion Connector
•A USB Type C port at 5V (not supported on SD 600eval Board)
The SD 600eval board exceeds the power input requirement and can operate from as low as 6.5V power input.
Please see section 8.2 for detailed information on SD 600eval implementation of DC Power.
6.11 Power Measurement
The 96Boards CE specification calls for support for measuring power consumptions of the board. Please see section 8.4 for
detailed information on SD 600eval power measurement implementation.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

16/30
6.12 External Fan Connection
The SD 600eval board can drive 5V or 12V DC fan. The power for driving external Fan is available on the Low Speed Expansion
connector.
6.13 UART
The 96Boards CE specification calls for support for one SoC UART and an optional second UART, both to be routed to the Low
Speed Expansion Connector.
The SD 600eval meets these requirements by routing APQ8064 GSBI 1 port as full UART and GSBI 7 port as debug UART, to low
speed expansion connector.
6.14 Buttons
The 96Boards CE specification calls for the presence of button switch to manually Power up/down & Reset the board.
The SD 600eval meets the board reset requirement. The power button SW2 can be used to sleep/wakeup the board. The reset
button SW3 is used to reset the board.
Additionally, SD 600eval also provides a user configurable switch SW1 on board.
6.14.1 Power Button
The push-button SW2 serves as the sleep/wakeup button. Upon applying power to the board, the boot process will start. Once
the board boot process is completed, user can go to Power off selection on Android UI by pressing the button for more than 5
seconds. If the board is in a sleep mode, pressing the power button will wake up the board.
(Above functionality of power button is tested over Android release)
6.14.2 Reset Button
The on board SW3 push-button serves as a reset button. Button press with duration of more than 10 seconds will cause a
system reset.
6.15 LED Indicators
The 96Boards CE specification calls for six LEDs to be implemented on the board. The specification defines the LEDs color and
mechanical location on the board.
Two activity LEDs:
• Wi-Fi activity LED is a surface mount Yellow color LED, 0603 size. The SD 600eval board drives this Yellow LED via
MPP_07 (PMIC GPIO).
• BT activity LED is a surface mount Blue color LED, 0603 size. The SD 600eval board drives this Blue LED via MPP_08 (PMIC
GPIO).
Four User-LED’s:
The four user LEDs are surface mount Green LED, 0603 size, located next to the two USB type A connector and labeled
‘USER LEDS 3 2 1 0’.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

17/30
6.16 Additional Functionality
The 96Boards CE specification allows for additional functionality, provided that all mandatory functionalities are available.
The SD 600eval board implements few additional functions, which are listed in the following sections.
6.16.1 GPS
SD 600eval board GPS implementation is based on Qualcomm WGR7640 GNSS RF receiver (U6). The APQ8064 communicates
directly with the WGR7640.
The SD 600eval board has two options for GPS antenna:
•External antenna at connector (J7) [default setting]
•On board antenna (ANT1)
6.16.2 SATA
For external storage, the SD 600eval board has one SATA 1.0 interface. The SATA signals of APQ8064 are routed to 13 Pin Slim
line SATA connector (J1).
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

18/30
6.16.3 Magnetometer, Gyroscope & Accelerometer Interface
Magnetometer, Gyro meter & Accelerometer interface are provided on SD 600eval board. The Magnetometer functionality is
implemented using LIS3MDLTR (U46) and Gyro meter & Accelerometer functionality is implemented using LSM6DS3H (U45),
interfaced with the APQ8064 via I2C interface.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

19/30
6.16.4 JTAG
The 96Boards CE specification allows for an optional JTAG connector.
On SD 600eval board, APQ8064 JTAG signals are routed to a non-standard Dual Row 20 Pin JTAG connector J17 (5-104655-3).
The following tables show the JTAG Connector pin out:
Pin
No.
Signal Name
Pin No.
Signal Name
1
JTAG_CONN_VREF
11
CPU_JTAG_TDO
2
VCC_5V0/VCC_3V0
12
GND
3
CPU_JTAG_TRST#
13
CPU_JTAG_RTCK
4
GND
14
GND
5
CPU_JTAG_TDI
15
CPU_JTAG_SRST#
6
GND
16
GND
7
CPU_JTAG_TMS
17
GND
8
GND
18
GND
9
CPU_JTAG_TCK
19
GNS
10
GND
20
TAG_CONN_DET_N
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

20/30
7. Expansion Connectors
The 96Board CE specification calls for one Low speed expansion connector and one High speed expansion connector.
7.1 Low Speed Expansion Connector
The low speed expansion connector brings GPIO and other low speed interfaces for the Expansion Board connection. The
connector is a dual row, low profile 2mm, 40 pin female receptacle J5 (9-1734516-0)
The following tables show the Low Speed Expansion Connector pin out:
Pin
No.
SD 600eval Signals
Pin
No.
SD 600eval Signals
1 GND
2
GND
3
LS_EXP_UART_1_CTS (APQ GPIO_20)
4
PWRBTN#
5
LS_EXP_UART_1_TX
(APQ GPIO_82)
6
RSTBTN#
7
LS_EXP_UART_1_RX (APQ GPIO_83)
8
LS_EXP_SPI_CLK
9
LS_EXP_UART_1_RFR (APQ GPIO_21)
10
LS_EXP_SPI_MISO
11
LS_DEBUG_UART_TX (APQ GPIO_18)
12
LS_EXP_SPI_CS_N
13
LS_DEBUG_UART_RX (APQ GPIO_19)
14
LS_EXP_SPI_MOSI
15
LS_EXP_I2C0_SCL (APQ GPIO_7)
16
LS_EXP_I2S_WS
17 LS_EXP_I2C0_SDA (APQ GPIO_6)
18
LS_EXP_I2S_SCLK
19
LS_EXP_I2C1_SCL (APQ GPIO_23)
20
LS_EXP_I2S_DOUT
21
LS_EXP_I2C1_SDA (APQ GPIO_22)
22
LS_EXP_I2S_DIN
23
LS_EXP_GPIO_A (APQ GPIO_35) (APQ INT)
24
LS_EXP_GPIO_B
25
LS_EXP_GPIO_C (APQ GPIO_55) (TS_INT_N)
26
LS_EXP_GPIO_D
27
LS_EXP_GPIO_E (APQ GPIO_29)
(GYRO_ACCL_INT_N)
28
LS_EXP_GPIO_F
29
LS_EXP_GPIO_G (APQ GPIO_0) (DSI_VSYNC)
30
LS_EXP_GPIO_H
31
LS_EXP_GPIO_I (APQ GPIO_28) (CSI0_RST)
32
LS_EXP_GPIO_J
33
LS_EXP_GPIO_K (APQ GPIO_34) (CSI1_RST)
34
LS_EXP_GPIO_L
35
LS_EXP_1P8
36
SYS_12V_DCIN
37
VCC_5V0
38
SYS_12V_DCIN
39
GND
40
GND
7.1.1 UART {0/1}
The 96Boards CE specification calls for a 4-wire UART implementation and an optional 2-wire UART on the Low Speed Expansion
Connector.
The SD 600eval board implements UART0 as a 4-wire UART that connects directly to the APQ8064 SoC. These signals are driven
at 1.8V.
UART1 is implemented as a 2-wire UART that connects directly to the APQ8064 SoC. These signals are driven at 1.8V.
7.1.2 I2C {0/1}
The 96Boards CE specification calls for two I2C interfaces to be implemented on the Low Speed Expansion Connector.
The SD 600eval board implements both interfaces, I2C0 and I2C1 that connects directly to the APQ8064 SoC. I2C lines are pulled
up with 2.2K resistor at 1.8V voltage level.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.