ArtFox Solar Wash M User manual

Solar Wash M
12x40w RGBW LEDs, Beam Wash 2-in-1
User manual
P le a se rea d t he ins t r u ct ion s ca refu ll y before use
TABLE OF CONTENTS

2
1. S af ety I nst r uctions ................................................................................................... 2
2. Technical Specifications ......................................................................................... 4
3. How To Control The Unit ..................................................................................... 5
4. shape ...................................................................................................................... 13
5. Trouble shooting ................................................................................................... 13
6. Fixture Cleaning .................................................................................................... 14
statement
The product has well capability and intact packing when leave
factory. All of the user should comply with warning item and manual, any
misuse cause of the damages are not included in our guarantee, and
also can not be responsible for any malfunction & problem owing to
ignore the manual.
1. S af ety I nst r uctions
Please keep this User Guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
 Unpack and check carefully there is no transportation damage before using
the unit.
 Before operating, ensure that the voltage and frequency of power
supply match the power requirements of the unit.
 It’s important to ground the yellow/green conductor to earth in order
to avoid electric shock.
 The unit is for indoor use only. Use only in a dry location.
 The unit must be installed in a location with adequate ventilation, at
least 50cm from adjacent surfaces. Be sure that no ventilation slots are
blocked.
 Disconnect main power before replacement or servicing.

14
p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess
s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Ch eck if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta g e c a b les th a t
m a y c a us e d a m a g e or in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is
b r oken.
2. The motor ’ s drive IC on the PCB might be out of condition.
7. Fixture Cleaning
Th e clean ing o f inter na l a nd ex ter na l optica l lens es a nd/or m ir r ors m u s t b e c a rr ied
ou t p eriodica lly to optim iz e ligh t ou tput . Cle a nin g f r eq uency d e p end s on t h e
environm ent in w hich t h e f ixture ope r a tes : d a m p , s m oky o r p a r tic ula r ly d ir ty
s urr ound ing c a n c a us e g r eat er acc um ula tio n of d ir t on th e u nit’ s optics .
 Cle a n with s oft clo th u s ing no r m a l g l a ss clea ni ng fluid .
 A lw a y s d r y th e parts ca r ef ully .
 Cle a n th e ex ter na l optic s a t leas t ev ery 20 days. Cle a n th e in ter na l opti cs a t
lea s t ev ery 30/60 days.
3
 Make sure there are no flammable materials close to the unit while operating as
it is fire hazard.
 Use safety cable when fixes this unit. DO NOT handle the unit by taking its head
only, but always by taking its base.
 Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the
temperature is higher than this Unit surface temperature may reach up to 85℃.
DO NOT touch the housing bare-hand during its operation. Turn off the power
and allow about 15 minutes for the unit to cool down before replacing or serving.
 In the event of serious operating problem, stop using the unit
immediately.Never try to repair the unit by yourself. Repairs carried out by
unskilled people can lead to damage or malfunction. Please contact the
nearest authorized technical assistance center. Always use the same type
spare parts.
 DO NOT touch any wire during operation as high voltage might be causing
electric shock.
Warning:
 To prevent or reduce the risk of electrical shock or fire, do not expose the unit to
rain or moisture.
 DO NOT open the unit within five minutes after switching off.
 The housing, the lenses, or the ultraviolet filter must be replaced
if they are visibly damaged.
Caution:
There are no user serviceable parts inside the unit. DO NOT open the housing
or attempt any repairs yourself. In the unlikely event your unit may require
service, please contact your nearest dealer.

4
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that
the unit is firmly fixed to avoid vibration and slipping while operating.
And make sure that the structure to which you are attaching the unit is secure
and is able to support a weight of 10 times of the unit’s weight. Also always use a
safety cable that can hold 12 times of the weight of the unit when installing the
fixture.
The equipment must be fixed by professionals. And it must be fixed at a place
where is out of the touch of people.
2. Technical Specifications
Light Sources: 12 x 40W 4in1 RGBW osram LED
Beam Angle: 6.5°~ 45°
Power Consumption: 500W
Power Voltage: AC 100-240V, 50/60Hz
Dimension: 32* 25.6* 40.1 cm
Net Weight: 12.5 Kgs
Packing size: 50.5x32.5x39cm
Control
DMX Channel: 19/31 Channel
Control Modes: DMX512/mater-Slave/Auto Run/Music
Pan/Tilt
Pan/Tilt: 540°or 360°in optional / 270°
Pan/Tilt Resolution: 8/16 bit
One full route of pan finished time is 2.4 seconds
Construction
Display: 180°reversible LCD colorful Display
Data In/Out socket: 3-pin & 5-pin XLR sockets
Power Socket: PowerCon in/out
Protection Rating: IP20
13
5.Shape
6. Trouble shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e
s o m e s ug g es tion s fo r eas y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Ch eck th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a g e on th e m a i n co nn e ct o r .
3. Ch eck th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link

12
28
40--59 Zone 2
60--79 Zone 3
80--99 Zone 4
100--119 Zone 1+2+3
120--139 Zone 1,2,3 rotate counterclockwise
140--159 Zone 1,2,3 rotate clockwise
160--179
change between zone 4 and zone 1+2+3
180-255 keep zone 4,zone 1,2,3 counterclockwise
29 0--255 flexible figure speed from fast to slow
30 0--255 flexible figure gradual change from fast to
slow
31
0-79 No function
80--99 Reset
100--255 No function
5
Features
Motorized liner zoom system, zoom range: 6°~45°
Outstanding color macro effect
Dimmer: 0~100% smooth dimming
Variable strobe effects
Fast, quiet operation and flicker free
4 zones different control
3. Lux Date
4. How To Control The Unit
Th e D M X512 is w id ely used in intellig ent ligh ti ng co n tr ol,with a DMX 512
controller.connect several lights together,dmx in and dmx out,

6
3 p in XLR co nn ectors : Pin 1: G ND , Pin 2: Nega tive s ig n a l (-), Pin 3: P o s itive s i gna l
(+)
Display:
MENU To select the programming functions
DOWN To go backward in the selected functions
uP To go forward in the selected functions
ENTER To confirm the selected functions
Set DMX Address Code
1 Press "Menu" to "Set DMX Address",and press"ENTER" keys to enter into
2 Show "Set DMX Address DMX Address:001",Press the "UP and DOWN"
keys to amended
3 Press "ENTER"keys to save and Exit,Press the"MENU"Keys does not save and
Exit
1.Address Set address code 001--512
2.Run Mode 1.DMX512
11
8
100--149 Mode 3
150--255 Mode 4
9 0--255 zoom
10 0--255 R
11 0--255 G
12 0--255 B
13 0--255 W
14 0--255 R
15 0--255 G
16 0--255 B
17 0--255 W
18 0--255 R
19 0--255 G
20 0--255 B
21 0--255 W
22 0--255 R
23 0--255 G
24 0--255 B
25 0--255 W
26 0--16 No function
17--255 Rainbow
27 0--49 No function
50--255 color auto run from fast to slow
28
0--19 No function
20--39 Zone 1

10
16
100--119 Zone 1+2+3
120--139 Zone 1,2,3 rotate counterclockwise
140--159 Zone 1,2,3 rotate clockwise
160--179 change between zone 4 and z
one 1+2+3
180-255 keep zone 4,zone 1,2,3 counterclockwise
17 0--255 flexible figure speed from fast to slow
18 0--255 flexible figure gradual change from fast to
slow
19
0-79 No function
80--99 Reset
100--255 No function
31 channels
channe
l
value Description
1 0--255 Pan
2 0--255 Pan fine-adjust
3 0--255 Tilt
4 0--255 Tily fine-adjust
5 0--255 Pan tilt speed
6
0--15 No function
16--214 strobe from slow to fast
215--255 random strobe
7 0--255 Dimming
8
0--49 Mode 1
50--99 Mode 2
7
2.AUTO
3.SOUND
3.Reverse
1.Pan 1.Yes reverse
2.Tilt
2.No forward
3.Display
4.Channel
1.31Channels
2.19Channels
5.Pan Degree
1.540
2.360
6.Mic Sense 001--100 sound control adjust
sensitiveness
7.Inform
7.Inform
1.CH Value display all channel values
2.Temp display led board temperature
3.Soft v3.0 software version number
8.Reset 1..Yes

8
2.No
9.Default
1.yes
2.No
10.Adjust
Pass Word UP+DOWN+UP+DOWN
RGBW 0-255 Change the value to
adjust brightness temperature
1.Pan Pan fine-adjust
2.Tilt Tilt fine-adjust
3.Focus Zoom fine-adjust
4.Red
Change the value,adjust the
white balance
5.Green
6.Blue
7.White
DMX channel´s functions and values (19/31DMX channels):
19 channels
channel value Description
1 0--255 Pan
2 0--255 Pan fine-adjust
9
3 0--255 Tilt
4 0--255 Tilt fine-adjust
5 0--255 Pan tilt speed
6
0--15 No function
16--214 strobe from slow to fast
215--255 random strobe
7 0--255 Dimming
8
0--49 Mode 1
50--99 Mode 2
100--149 Mode 3
150--255 Mode 4
9 0--255 zoom
10 0--255 R
11 0--255 G
12 0--255 B
13 0--255 W
14 0--16 No function
17--255 Rainbow
15 0--49 No function
50--255 color auto run from fast to slow
16
0--19 No function
20--39 Zone 1
40--59 Zone 2
60--79 Zone 3
80--99 Zone 4