Artic AR-DB16F User manual

FIBER ACCESS TERMINAL CLOSURE
AR-DB16F
INSTALLATION
MANUAL

1. General Introduction
Thisboxisusedasaterminationpointforthefeedercabletoconnectwiththedropcablein
FTTxcommunicationnetworksystem.
Itintegratesfibersplicing,splitting,distribution,storageandcableconnectioninoneunit.
Meanwhile,itprovidessolidprotectionandmanagementfortheFTTxnetworkbuilding.
2. Specification
3. Structure
3.1Closureandaccessories（Picture1）
Dimension（mm）
Weight（kg）
Cableports
Splicetrayquantity
287×172×102
4.5~5
1inputcableportforun-
cutcablefromdiameter
from10~17.5mm.
16outputcableportsfor
cablediameter2.0*3.0
1
Max.capacity(Singlefiber)
Sealingtype
Singlesplicetray
capacity(Singlefiber)+Adapt
orsModule
Adaptercapacity
16
Mechanical
1
16+4
PICTURE 1
2
INSTALLATION MANUAL FIBER ACCESS TERMINAL CLOSURE AR-DB16F

3.2Standardparts
S/N
1
2
3
4
5
6
Description
Wallmountingkit
Expansionanchorbolt
KEY
Nylontie
Fusionsleeve
0.3mcoiltube
Quantity
1
4
1
10
Accordingto
thefibercores
1
Note
Forwallmounting
Partsofthewallmountingkit
Fixingcable
Cablesplicing
Protectthefiber
3.3Optionalparts
S/N
25
Description
Polemountingkit
Quantity
1
Note
Forpolemounting
1. Stripthecable
2. Opentheclosure
3. Installtheun-cutcable
4. Protecttheun-cutcable
5. Introducethecutcableintothesplicetray

6. Spliceandstorefibers
7. Fixingcables
4. Installation flow chart
3
INSTALLATION MANUAL FIBER ACCESS TERMINAL CLOSURE AR-DB16F

8. Closeandsealtheclosure

9. Installthefiberclosure
5. Working procedure
5.1Checkup
5.1.1(1)Checktheitemnumberandaccessoriesoffiberclosure.(2)Checkthefiber
specification.(3)Checkthepartsquantity.(4)Checktheinstrument.（Picture2）.
1. Transversecuttingknifeforcableoutersecuritylayer.
2.  Thelongitudinalopencableknife.
3.  Steelcorecutclamp.
4.  Crossscrewdriver.
5.  Scissors.
6.  Cuttingclamp.
3
2
1
6
4
5
PICTURE 2
4
INSTALLATION MANUAL FIBER ACCESS TERMINAL CLOSURE AR-DB16F

5.2 Theproceduretostripthecablefiber
5.2.1Markthecutpointonthecableaccordingtothedifferentlengthrequirements.
5.2.2Stripthecableouterlayer.
5.2.3Therequirementforstrippingtheun-cutcable.（1）Thelengthshouldbenolessthan
2000mm；（2）Cutthesteelcoreatthelengthof50mmofthecablecutpoint.（Picture3-1).
5.3Opentheclosure
5.3.1Usethetooltoprybuckles.（Picture4）
5.3.2Openthelid,takeouttheaccessories.（Picture5）
Note:Besurenottodamagefiber.Don'tuseanydamagedcable.
PICTURE 3-1
PICTURE 3-2
≥2000mm
50mm
≥1000mm
50mm
5
INSTALLATION MANUAL FIBER ACCESS TERMINAL CLOSURE AR-DB16F

5.4 Un-cutcableandbranchcableworkingprocedure
5.4.1.Removetheplasticnutsandtakeoutthecablesealingcomponentsasbelowpictures.
(Picture6/7/8).
PICTURE 4
PICTURE 6 PICTURE 7 PICTURE 8
PICTURE 5
6INSTALLATION MANUAL FIBER ACCESS TERMINAL CLOSURE AR-DB16F

PICTURE 9-1 PICTURE 9-2
PICTURE 10 PICTURE 11
5.4.2.Cutthegrommettopassthroughtheun-cutcable.(Aspicture9-1andpicture9-2）.
5.4.3.Splittheothertwocomponents,accordingtothesequencetoinstalltheun-cutcable
mountingcomponents.（Aspicture10）.
5.4.4.Afterthecablepassingthroughtheportsintothebox,tightenthehoseclamps,fixing
cable.（Aspicture11）.
7
INSTALLATION MANUAL FIBER ACCESS TERMINAL CLOSURE AR-DB16F

PICTURE 12
PICTURE 13
5.4.5.Fixbackthebriquettingoftheinputport.（Aspicture12）
5.4.6.Cablegetsthroughinturntheplasticnut,washer,grommet,washerasbelowpicture
(picture13),theninstalltotheclosureport.
5.5Clearupthecablerouting
5.5.1Protectthebarefiberbycoiltubeandclearupthecable.（Aspicture14）.
8
INSTALLATION MANUAL FIBER ACCESS TERMINAL CLOSURE AR-DB16F

PICTURE 14
PICTURE 15
5.6Introducethecutcableintothesplicetray
5.6.1Protectthebarefiberbycoiltubeandclearupthecable,thenintroduceintothesplice
tray.（Aspicture15）.
5.7Fibersplicingprocess
5.7.1Opensplicetray.（picture16）.
5.7.2Installtheadaptorontheadaptorholder.
5.7.3Windingandsplicethepigtail.
5.7.4InstallandwindthePLCsplitter.(Aspicture17）.
9
INSTALLATION MANUAL FIBER ACCESS TERMINAL CLOSURE AR-DB16F

PICTURE 16
PICTURE 17
5.8Softcableportworkingprocedure
5.8.1Forpre-terminatedcable,first,insertthedropcabletopassthroughtheboxintothe
cablehole,insertingrubberplugandtransparentfixture.Thenpullouttheappropriatelength
ofcable,toremainsuitabletoaddafastconnector.Closingthetransparentfixture.Andfinally,
pluggingtherubberplugandthefixturetogetherintotheboxintothecablehole.
5.9Closethefiberclosure
5.9.1ClosetheclosureandclosetheTwobuckles,alsotightenthebolts.
5.7.5Coverthesplicetraycoverandputbackthetoolonthetraycover.
10
INSTALLATION MANUAL FIBER ACCESS TERMINAL CLOSURE AR-DB16F