Avigilon NVR5-10GBASET-A1 User manual

Avigilon NVR5 10G Base-T Kit
Installation Guide
Installation Guide
NVR5-10GBASET-A1
For
NVR5 STD 16TB-64TB
NVR5 PRM 96TB-160TB
1

© 2022,Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILON are trademarks
of Avigilon Corporation. Intel is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other
countries. Other names or logos mentioned herein may be the trademarks of their respective owners. The
absence of the symbols ™ and ® in proximity to each trademark in this document or at all is not a disclaimer of
ownership of the related trademark.
This document has been compiled and published using product descriptions and specifications available at
the time of publication. The contents of this document and the specifications of the products discussed
herein are subject to change without notice. Avigilon Corporation reserves the right to make any such
changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the
completeness or accuracy of the information contained in this document; or (2) is responsible for your use of,
or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages
(including consequential damages) caused by reliance on the information presented herein.
Avigilon Corporation
avigilon.com
20220617
2

Table of Contents
Introduction 4
Confirm Package Contents 4
Recommended Tools 4
Installing the NVR5 10G Base-T Kit 5
Opening the Cover 6
Installing the 10G Base-T Card 8
Reattaching the Cover 9
Confirming the Installation 10
For More Information 11
3

Introduction
Avigilon provides an optional 10G Base-T Kit for the NVR5 Standard 16-64TB and Premium 96-160TB. This
kit provides you with high-speed Ethernet ports for faster connections to your security network of ACC
Servers and Clients.
Part Number Description
NVR5-10GBASET-A1 NVR5 Standard/Premium 10G Base-T Upgrade Kit
Confirm Package Contents
Confirm that the kit you are installing contains the following components:
o1 × 4-port 10G Base-T PCIe card
Recommended Tools
The following tools are not included in the kit package, but are needed to complete the installation:
lPhillips #2 screwdriver
lWrist-grounding strap connected to the ground
lESD Mat
Important: It is recommended that you always use an antistatic mat and antistatic strap while
working on components inside the system.
Introduction 4

Installing the NVR5 10G Base-T Kit
Note: If the NVR5 is an operating part of your security system, be aware that it must be shut down to
complete this procedure.
Before starting to install the kit:
1. Turn off the NVR5, including all attached peripherals. Press the power button on the front panel, and
wait for the light to stop blinking to indicate shutdown is complete.
WARNING — Opening or removing the system cover while the system is powered on may
expose you to a risk of electric shock.
2. Disconnect the NVR5 from the electrical outlet and disconnect the peripherals.
3. Remove all network, power and peripheral cables from the NVR5.
4. If applicable, remove the NVR5 from the rack.
Important: Whenever you need to lift the system, get others to assist you. To avoid injury, do
not attempt to lift the system by yourself.
Installing the NVR5 10G Base-T Kit 5

Opening the Cover
1. At the top of the NVR5, unlock the latch release then lift and rotate the latch towards the back of the
unit. The cover slides back and is released from the body.
Tip: Use a Phillips #2 screwdriver to remove the shipping screws before unlatching the cover
if you are removing the cover of an NVR5 for the first time.
2. Remove the air shroud by holding it at both ends and lifting it away from the system.
Opening the Cover 6

3. View the interior of the NVR5 and identify the locations where the components of the kit will be
installed.
The view below shows the details of an NVR5 with all of the covers and cards removed, and important
components labeled with numbers.
The components affected by the NVR5 10GBase-TUpgrade Kit are:
l6—Expansion card riser
The 10GBase-T card will be installed in one of the empty expansion slots to the left of this riser
(either slot 5 or 6 depending on your NVR5 model).
Opening the Cover 7

Installing the 10G Base-T Card
With the NVR5 open:
1. Unpack the 10GBase-T card.
2. Locate the slot in which the Base-T card will be installed and remove the PCI expansion slot cover
from the back panel of the NVR5:
lFor an NVR5 Premium system, the card will be installed in slot 5.
lFor an NVR5 Standard system, the card will be installed in slot 6.
3. Insert the card edge connector firmly into the appropriate expansion card slot until the card is fully
seated.
Installing the 10G Base-T Card 8

Reattaching the Cover
When all the components of the kit have been installed:
1. Reinstall the top of the cooling shroud:
a. Align the slot on the air shroud with the standoff in the system.
b. Lower the air shroud into the system until it is firmly seated.
2. Close and lock the NVR5 cover.
3. If the NVR5 was rack mounted and removed to install the kit, remount it into the rack.
4. Reconnect all the peripherals and cables.
Important: Ensure that both of the power supplies are connected to main power. The
upgraded NVR5 requires both power supplies to properly function.
5. Power on the NVR5.
Reattaching the Cover 9

Confirming the Installation
From an ACC Client running on a workstation with a network connection to the ACC site associated with the
NVR5:
1. Log in to ACC site.
2. Click in the menu bar and scroll down and click Site Setup.
3. In the Search panel, click to expand the site containing the NVR5 in which the 10G Base-T card is
installed.
4. Navigate to (or search for) the upgraded NVR5 and click .
5. Verify that the NVR5 has one additional 10GbE adapter with four ports available:
a. In the System Explorer, select the upgraded NVR5 server.
b. In the New Task menu , click Site Health.
c. Under the Network Adapters heading, there should be four new ports installed in PCIe slot 5 or
6 (depending on Premium or Standard). These new ports should have a Link Speed of 10Gbps.
Limited Warranty
Avigilon warranty terms for this product are provided at avigilon.com/warranty.
Confirming the Installation 10

For More Information
For additional product documentation and software and firmware upgrades, visit support.avigilon.com.
Technical Support
Contact Avigilon Technical Support at support.avigilon.com/s/contactsupport.
For More Information 11