Article NERA Bed User manual

Assembly Instructions
NERA
Bed
VERSION 1.2

ASSEMBLY INSTRUCTIONS
Read these instructions carefully and keep for future
reference. Refer to parts inventory for guidance, and
ensure you have all pieces before starting.
When assembling, place all parts on a soft, clean, and flat
surface such as a carpet to prevent scratches.
If you’re having diculty, our friendly Customer Care
team is always here to help. Call us at 1.888.746.3455
during business hours, email [email protected] or chat
live at article.com.
NERA Bed Page 2 of 16
PARTS INVENTORY CONT.
ID DESCRIPTION QTY
LEG 2
CENTER BEAM 1
CENTER LEG BRACKET
PREINSTALLED 2
FLOATING CENTER LEG 2
SLAT CLIP 28
SLAT 28
SLAT CENTER BRACKET 14
PARTS INVENTORY
ID DESCRIPTION QTY
HEADBOARD 1
FOOTBOARD 1
CENTER BEAM BRACKET 2
LEFT SIDE RAIL 1
RIGHT SIDE RAIL 1
LEFT CORNER PIECE 1
RIGHT CORNER PIECE 1
1+ hours
5
TIME
# OF PEOPLE
DIFFICULTY
REQUIRED TOOL
Phillips screwdriver

HARDWARE / TOOLS INVENTORY
ID DESCRIPTION QTY
TEFLON PAD 2
ALLEN KEY 1
M6 ×12MM BOLT 4
LONG COMPRESSION
FITTING ANCHOR 4
SHORT COMPRESSION
FITTING ANCHOR 10
HARDWARE / TOOLS INVENTORY CONT.
ID DESCRIPTION QTY
M8 ×8.5MM SCREW 8
M6 ×20MM BOLT
4 PREINSTALLED ON CENTER LEGS 12
M8 ×15MM BOLT 4
M7.5 ×7MM SCREW 6
NERA Bed Page 3 of 16
Structural integrity is warranted only if all
fasteners are properly installed & tightened,
and the bed is moved only per instructions.
DO NOT DRAG BED, ALWAYS LIFT WITH
AT LEAST TWO PEOPLE BEFORE MOVING

Page 4 of 16
1A
NERA Bed
×2
First remove plastic backing
from teflon pads (O). Stick on
bottom side of headboard (A)
approx. 1/4” in from the edges.
!

Page 5 of 16
1B
NERA Bed
×4
Use the 4 shortest
bolts (Q) provided.
!
!
Ensure center beam brackets (C)
are level when installed.
!

Page 6 of 16
2
NERA Bed
×6
Holes on compression fitting anchors
must be facing inwards on headboard (A).
Ensure rubber seal on anchors are tight.
!

Page 7 of 16
×4
Holes on short compression fitting anchors (S)
must be facing down on footboard (B).
Ensure rubber seal on anchors are tight.
!
3
NERA Bed

Page 8 of 16
4
THIS SIDE UP
THIS SIDE UP
×4
NERA Bed
Holes on short compression fitting anchors (S)
must be facing down on side rails (D/E).
Ensure rubber seal on anchors are tight.
!

Page 9 of 16
5
NERA Bed
THIS SIDE UP
THIS SIDE HEADBOARD
THIS SIDE UP
THIS SIDE HEADBOARD
×4
Note placement of holes on each
corner piece, left vs. right.
!

Page 10 of 16
6
NERA Bed
!
×8

Page 11 of 16
7A
THIS SIDE UP
THIS SIDE UP
×4
Labels on side rails indicate orientation.
THIS SIDE UP
!
NERA Bed
Ensure side rails (D/E) are parallel with
footboard (B) when tightening bolts (V).
!

Page 12 of 16
7B
THIS SIDE UP
THIS SIDE UP
×4
NERA Bed
×6

Page 13 of 16
8
NERA Bed
Unscrew bolts (U) from center leg
brackets (J) and floating center legs (K)
before attaching to center beam (I).
Attach floating center legs (K) where labels are
situated on center beam (I). Ensure that legs
are straight, perpendicular to center beam.
!
!
CENTER LEG
CENTER LEG
CENTER LEG
CENTER LEG
CENTER LEG
CENTER LEG
CENTER LEG
CENTER LEG
CENTER LEG
×4

Page 14 of 16
THIS SIDE UP
THIS SIDE UP
THIS SIDE HEADBOARD
THIS SIDE UP
THIS SIDE HEADBOARD
9
Insert pins on center beam brackets
into center beam when installing.
!
×2
NERA Bed
Adjust levelers on floating center legs
to allow for a 3-5mm clearance.
!

Page 15 of 16
NERA Bed
10A
10B
THIS SIDE UP
THIS SIDE HEADBOARD
THIS SIDE UP
THIS SIDE HEADBOARD
×28
×28

Page 16 of 16
11
THIS SIDE UP
NERA Bed
DO NOT DRAG BED, ALWAYS LIFT WITH
AT LEAST TWO PEOPLE BEFORE MOVING
×28 ×14
First, firmly insert pins on
slat clips into side rails.
!
Second, firmly insert pins on slat
center brackets into center beam.
!