Artistry AQUABRASION User manual

SKINCARE DEVICE

2
• Device Structure pg. 3
• Charging Information pg. 3
• SUCTION Mode pg. 4
• SERUM Mode pg. 5
• Cleaning Method pg. 6
• Weekly System Regimen pg. 7
• Safety & Caution pg. 8
• Technical Information pg. 9
• Certifications / Marks of Conformity pg. 10
• Distributor & Manufacturer Contact Information pg. 10
• Customer Service Information pg. 10
• Warranty pg. 10
Artistry Labs™ Aquabrasion is intended to be used as part of ARTISTRY LABS™ Retexturizing System with
ARTISTRY LABS™ Retexturizing Peel and ARTISTRY LABS™ Retexturizing Serum. See page 7 for complete
Treatment System instructions. This 28 Day Skincare System is recommended to be used every quarter.
NOTICE: Before using the device for the first time, it is essential to read the instructions and safety
information in this booklet to ensure proper use and to achieve your best results. We recommend saving these
instructions for future reference.
ENGLISH pg. 1
Notice
Language Reference
Components
• Device x 1
• Device Cradle x 1
• Water Tank Holder x 1
• SUCTION Nozzle Head x 2
(1 Large/1 Small Nozzle)
• SERUM Dome Attachment x 1
• USB-C Cable x 1
• User Manual x 1
• Cleaning Brush x 1
Device
Water Tank Holder
Cradle
SERUM Dome Attachment
User Manual
SUCTION Nozzle Head
USB-C Cable Cleaning Brush
Table of Contents
Device Information

3
Device Structure
Before Use: Charge the Device with USB-C Cable provided. Charging time can vary by country and outlet.
How To Charge
1. Ensure Tanks are empty. Securely place the Device upright in the
Cradle.
2. Use the USB-C Cable provided to charge the Device*
3. A red light will be displayed around the POWER Button while
charging. When the Device is fully charged, the light will turn
green.
4. When charging is complete, unplug. The Device will not operate
while plugged in.
* 5V adapter is required (not included).
Do not use a quick/fast USB adapter.
Charging Information
Low Battery Indicator
When the battery Power is less than 5%, the Device will beep several times and a red light will blink around the
POWER Button. The Device will not work. Follow the steps above to charge the Device.
Turning the Device On/O and Changing Modes/Levels
• To turn the Device on, press the POWER Button. A white light will indicate the Device is on.
• To select the appropriate Suction level, press the POWER Button again for Level 1;
press twice for Level 2; press three times for Level 3.
• To select SERUM Mode, press the SERUM Button once the Device is on.
• To turn the Device o, press and hold the POWER Button for 2 seconds.
NOTE: You may turn the Device o whenever necessary or desired.
SERUM Button
Charging Port
Water Drain Hole
Water Tank
Power Button
Water Supply Tube
Suction Nozzle
Waste Tank
Bottom Cap
Level Sensor
SERUM Dome Attachment

LEVEL DESCRIPTION
Level 1 Low Suction Blue
Yellow
Pink
Level 2 Medium Suction
Level 3 High Suction
INDICATOR LIGHT
4
Suction Nozzle Selection
There are two sizes of Suction Nozzles for dierent areas of your face.
• Small Nozzle: For smaller crevices like the nose area.
• Large Nozzle: For larger areas like the forehead, cheeks, and chin.
Changing the Suction Nozzle
Ensure the Device is o prior to changing the Suction Nozzles. To remove the Suction Nozzle from the Device,
gently pull outward. To replace the Nozzle, align the point on Nozzle with the triangle on Device and firmly push
it into place while sliding onto the ports.
NOTE: When changing Nozzles, it is easier to do when hands are dry.
Suction Levels
The Device has three Suction Levels to choose from depending on your skin tolerance. We suggest starting with
Level 1 and then increasing intensity depending on your comfort Suction Level. Turn the Device on and select
the appropriate Suction Level by using the POWER Button: Press once more for Level 1; press twice for Level 2;
and press three times for Level 3.
Filling the Water Tank
1. Remove the Bottom Cap.
2. Firmly grip the top half of the Device and pull the
Water Tank down with the other hand to remove
it from the Device.
3. Fill the Water Tank with water until it reaches the
MAX limit line.
*Do not overfill past the MAX limit line.
4. Push the Water Tank securely back into place.
5. Replace the Bottom Cap.
SUCTION Mode Developed to use aer ARTISTRY LABS™ Retexturizing Peel
Suction Treatment Instructions
1. Place the appropriate Suction Nozzle on the Device.
2. Fill the Water Tank with water.
3. Turn the Device on by pressing the POWER Button.
4. Choose the appropriate Suction Level by pressing the POWER Button again accordingly.
*The Device will take a few seconds to “ramp up” and get up to speed.
5. Gently sweep the Device across the face ensuring the Suction Nozzle is in good contact with the skin.
Follow the diagram below for directions for treatment.
6. Continue until the entire face has been treated.

5
NOTE:
• Avoid the eye area.
• Do not hover the Device in a single spot for more than 3 seconds.
• If the Device is tipped too much, the Device will shut o. Restart the Device and continue treatment.
• Stop if you feel excessive discomfort.
• You may experience slight redness of your skin during use. This is normal.
• Do not operate in Suction Mode without water in the Water Tank.
• Empty the Waste Tank and refill the clean Water Tank as many times as necessary throughout treatment.
The Waste Tank is not removable from the Device
• Do not shake, tip, or lay the Device down when the Waste Tank or Water Tank contains water.
• The Device will automatically turn o aer 5 minutes of use in Suction Mode to save power.
If needed, turn the Device back on and continue the treatment.
When Suction Treatment is Complete
1. Press the POWER Button for 2 seconds to turn the Device o.
2. Hold the device upright over the sink then slightly tilt to avoid spilling over your hands.
3. Remove the bottom cap from the Waste Tank to allow the wastewater to drain then replace the cap and
follow cleaning instructions.
4. Ensure the Device and Suction Nozzles are properly cleaned and dry.
SERUM Treatment Instructions
1. Attach the SERUM Dome Attachment to the Device by aligning the point on the Dome
Attachment with the triangle on the Device.
2. Push the Dome Attachment into place while sliding onto the ports.
3. Turn the Device on by pressing the POWER Button.
4. Press the SERUM Button. A red light will appear inside the Dome Attachment.
5. Starting at the top of the forehead, lightly touch the Dome on the face. The Device will
beep aer 3 seconds. 2-3 cm (1 inch) and repeat until the entire face is treated.
NOTE:
• Avoid the eye area.
• Do not shine the LED light into the eyes. If necessary, close eyes during treatment.
• SERUM Mode will last 10 minutes, but you may turn the Device o at any time.
When the SERUM Treatment is Complete
1. Press the POWER Button for 2 seconds to turn o the Device.
2. Grasp the Dome Attachment by the sides with two fingers and gently pull it outward
and rinse it to clean.
3. Return the Device to the Cradle and plug it in to charge.
SERUM Mode Developed to use aer ARTISTRY LABS™ Retexturizing Serum
Forehead Cheeks Chin Nose area *Use your free hand
to hold skin firm.
The large nozzle The small nozzle

6
Cleaning Method Please turn o the Device before cleaning.
Cleaning Mode aer Using the SUCTION Mode
1. Place the Large Suction Nozzle on the Device.
2. Fill the Water Tank with water until it reaches the MAX limit line.
3. Turn the Device on by pressing the POWER Button then press and
hold the SERUM Button for 2 seconds to start the Cleaning Mode.
4. Turn the Dome Attachment upside down and securely hold it on
top of the Large Suction Nozzle.
* Hold the Device upright. If the Device is tilted too much, it will
beep and shut o. If this occurs, hold the Device upright and turn
on to continue cleaning.
5. When the water in the Water Tank is exhausted, press and hold
the POWER Button for 2 seconds to turn the Device o.
6. Hold the device upright and remove the Bottom Cap to empty the
Waste Tank.
7. Separate the Water Tank and place it on the Cradle’s Water Tank Holder.
8. Remove the Large Suction Nozzle and gently rinse the Suction
Nozzles, Dome Attachment, and Bottom Cap with water.
9. Return the Device to the Cradle and allow all of the components
to completely dry.
How to clean the Waste Tank
1. Remove Bottom Cap and empty the Waste Tank.
2. Use the brush and dampen it to clean the Waste Tank walls
thoroughly and gently.
3. Return the Device to the Cradle and allow the Waste Tank to
completely dry.
NOTE:
• Avoid soap and excessive/aggressive wiping or brushing. It may
cause damage.
• Do not shake, tip, or lay the Device down when the Water Tank or
Waste Tank is filled with water. The Device should remain in the
upright position if either Tank still contains water.
• This is to protect the pump from water backflow if the Device is
tilted too much while the Waste Tank contains water.

7
ARTISTRY LABS™ Retexturizing System
This Treatment System consists of two dierent regimens: Peel Day and Non-Peel Day.
Follow this weekly regimen below for 4 weeks, ensure Peel is used on non-consecutive days:
DAY 1
PEEL DAY 2
NON-PEEL DAY DAY 3 NON-PEEL DAY DAY 4
PEEL
• Apply 2 pumps of Serum to the entire face using fingertips. Let fully absorb and completely dry.
• Apply 6-8 pumps of Peel with fingertips onto cleansed skin. Spread as a layer and leave on for 8 minutes.
• Thoroughly rinse face with water to remove Peel and pat dry.
• Use the Device + Suction Nozzle to remove skin debris and to extract pores. Pat skin dry.
• Apply 2 pumps of Serum to entire face using fingertips. Let fully absorb and completely dry.
• Follow with Device in SERUM mode + Dome Attachment.
AM:
• Apply 2 pumps of Serum to the entire face using fingertips. Let fully absorb and completely dry.
PM:
• Apply 2 pumps of Serum to entire face using fingertips. Let fully absorb and completely dry.
• Follow with Device in SERUM mode + Dome Attachment.
PEEL DAY INSTRUCTIONS:
DAY 5
NON-PEEL DAY DAY 6 NON-PEEL DAY DAY 7 NON-PEEL DAY
NON-PEEL DAY INSTRUCTIONS:
Skincare products and Device should avoid contact with eyes. If at any time persistent redness, burning, or stinging
occurs, discontinue use and/or rinse face. Follow AM and PM steps with a moisturizer.
Order of Use with your daily Skincare Regimen:
• Daytime Regimen: Cleanser, Toner, Retexturizing Serum, Moisturizer and/or SPF.
• Nighttime Regimen with Peel: Cleanser, Retexturizing Peel, Device + Suction Nozzle, Toner, Retexturizing
Serum, Device in SERUM Mode + Dome Attachment, Moisturizer.
• Nighttime Regimen without Peel: Cleanser, Toner, Retexturizing Serum, Device in SERUM Mode + Dome
Attachment, Moisturizer.
Weekly System Regimen
AM:
PM:

8
The manufacturer and distributors (pg.. 10) are not responsible for Device failure or damages as a result of not
following the use instructions and warnings set in this manual
Safety Statement
1. Do not use the Device if you
• have a facial implant (e.g. metal, silicone)
• have eczema, dermatitis, or other skin ailments
• are pregnant or breastfeeding
2. Consult a doctor:
• if you had recent facial surgery
• if you are under medical treatment
3. Do not use the Device on the following areas:
• Injured, inflamed, or irritated skin
• Where surgery was performed
• Eyes and areas around the eyes
• Where hair removal treatment has recently been performed (less than 24 hours)
• Areas with pain perception or sensory disabilities
Caution Statements
1. To avoid potential fire hazards, electric shock or injury, or damage to the Device.
• Do not expose the Device to extreme temperatures (higher than 45°C (113°F) or lower than 0°C (32°F)),
heat sources, direct sunlight, or flammable materials.
• Do not clean with flammable substances such as alcohol, benzene, or thinner.
• Do not use the Device if it emits smoke, odor, or unusual noise.
• Do not place the Device in a microwave or high-pressure container.
• Do not modify or repair the Device.
• Do not drop, throw, or apply heavy impact to the Device.
• Do not submerge the Device in water and avoid contact with a large amount of water.
• Do not charge the Device in a damp place.
• Use dry hands with charging cable/electrical outlet.
• Keep the Device out of the reach of children (under 12 years of age).
2. For optimal Device performance:
• Power o when not in use.
• Charge the Device by connecting the included USB cable to the 5V adapter to charge.
Do not use a quick/fast USB Adapter.
• Turn the Device o before charging.
• Fully charge the battery at least every 4 weeks when not in use. This will help maintain the battery lifespan.
• Turn the Device o prior to changing the suctions nozzles/dome. A malfunction may occur if the Device is
le on while changing the attachments.
• Do not turn the Device upside down.
• Do not use detergent or boiling water to cleanse the Suctions Nozzles / Dome Attachment as it may cause
discoloration or corrosion.
• Do not expose the Device or Components to direct sunlight for an extended period of time as it may cause
discoloration or aect product performance.
Safety & Caution

9
Product Name: ARTISTRY LABS™ AQUABRASION
Model Number: BD0030EBCOE
Rated Voltage/current: 3.7 V/ 1.4 A
Contains: Li-polymer 900 mAh Rechargeable Battery
USB-C cord included
Local Charger – not included
Charging indicator – present
Device size parameters (mm):
Body: 231.5(H) *52(W) *45(L)
Cradle: 108(H) *116.5(W) *76(L)
Device weight: 232.5g(main body), 85.2g(cradle)
Materials used:
Device Body Plastic: P.C+ABS white
Waster and Water Tank material : ECOZEN® †
Cradle material : ABS white
Nozzle Tips: Silicone
Cap lens: P.C
Operating temperature: 5°C ~ 25°C (41°F ~ 77°F)
Storage conditions: away from direct sunlight, in a dry place, out of children’s reach
Storage temperature: at -20°C ~ 25°C (-4°F ~ 77°F)
Battery: Model name XK603048
Battery Manufacturer : DONGGUAN LEAN POWER NEW ENERGY TECHNOLOGY CO., LTD.
No.198, Jin Chuan Road 2, Xie Gang Town, Dongguan, Guangdong, China.
Manufacture Date: Marked separately on battery
A/S center: 031-701-0951
Technical Information
†Ecozen is a registered trademark of SK Chemicals Co., Ltd.

10
Customer Service contact information:
USA: 1-800-253-6500
Canada: 1-800-265-5470
Hong Kong: (852) 2969 6300
Singapore: 65 65509911
DEVICE CERTIFICATIONS/MARKS OF CONFORMITY:
EC DECLARATION OF CONFORMITY
This electronic equipment is in conformity with relevant European harmonization legislation on consumer and
environmental safety
This Device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this Device may not cause harmful interference, and (2) this Device must accept any interference received,
including interference that may cause undesired operation.
WASTE AND ENVIRONMENT
This electronic equipment must be disposed separately from household waste at its life end.
Please dispose at your local recycling system.
Manufactured by DOCTORS TECH CO., LTD.
U-Techvalley B-9/F, 25, Misagangbyeonjungang-ro 7beonan-gil, Hanam-si, Gyeonggi-do, Republic of Korea 12939
DIST. BY AMWAY CORP., ADA, MI 49355 • DIST. BY/PAR AMWAY CORP., ADA, MI 49355 USA/É.-U. • DIST. BY AMWAY
Hong KONG LTD.
Country of Origin: Korea
A2300231
Warranty Information: Scan QR Code
© 2023 Alticor Inc. L174495ENA